Synthesis and polymerization of a new nitrogen‐containing bis‐ortho‐diynylarene monomer

This study focuses on the preparation, characterization, and optical properties of new bis(3,4‐diphenylethynylphenyl)phenylamine. This is the first nitrogen‐containing bis‐ortho‐diynylarene (BODA) monomer having a nitrogen atom as the spacer group. BODA monomers are usually prepared from common bisphenols, thereby providing great synthetic versatility and the opportunity to develop a wide array of novel polyarylene thermosets by varying the aromatic spacer group. The new bis(3,4‐bisphenylethynylphenyl)phenylamine was synthesized in five steps. This compound emits an intense blue color (λ = 438 nm) upon irradiation by UV light and may be suitable for use as an emitting layer in electroluminescent devices. Bis‐(3,4‐bisphenylethynylphenyl)phenylamine and its polymer have photoluminescence quantum yields 34 and 38%, respectively, and long excited‐state lifetimes of 3.2 and 3.6 ns, respectively. The structure of the monomer and its polymer were characterized using spectroscopic techniques including Ultraviolet–visible Spectrophotometer, Photoluminescence Spectrophotometer, Fourier Transform infrared spectroscopy, and Gel Permeation Chromatography. The polymerizations were studied by Differential Scanning Calorimeter. The amount of weight loss and the thermostability of the nitrogen‐containing polymer were determined from thermogravimetric analysis. The electrical conductivity of neat HCl‐doped BODA‐derived polymer film was measured according to the standard four‐point probe technique. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6988–6996, 2006     

A coincidence transmission electron microscope with digital waveform measuring system for analytical microscopy

We have been developing a new analytical transmission electron microscope (TEM), called a coincidence TEM, which in principle enables elemental mapping images to be observed at a high signal‐to‐noise (S/N) ratio under very low dose radiation conditions. In this paper, we report the development of a coincidence TEM with a digital waveform measuring system for obtaining a coincidence elemental mapping image. In this system, analog signals detected by a Si(Li) detector and a multianode, position‐sensitive photomultiplier (PSPM) are continuously converted into 12‐bit digital waveform data at a rate of 100 MHz, and transferred to a PC. From the transferred digital waveform data, information on X‐ray photon energy, electron incident position, and detection times of both X rays and electrons are calculated by digital waveform measurement, which lead to the observation of a successful coincidence elemental mapping image. Copyright © 2005 John Wiley & Sons, Ltd.     

A procedure for measuring the flexibility of single wood-pulp fibres

A way of determining the flexibility of wood-pulp fibres is developed, which involves i) a precise measurement of the topology of single-fibres by using a confocal laser scanning microscope and ii) the measurement of the elastic modulus of the fibres by using a single-fibre fatigue cell. Reported in this paper are the initial results of tests carried out on black spruce fibres, which have been subjected to three different levels of mechanical refining energy, namely ∼1100, 2300, and 3500 kWh/t. It is found that the fibre flexibility rises significantly between the first and second energy levels, but it does not change to the same degree between the second and third ones. The described procedure of measuring the flexibility of fibres may be used to establish the appropriate refiner energy necessary for the production of a specific grade of paper. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 115–128, January–February, 2006.     

Analytical Designing of Two-Aspherical-Mirror Anastigmats Permitting Practical Misalignments in a Soft-X-Ray Optics

A new analytical method of designing two-aspherical-mirror anastigmats was developed and applied to searching solution groups of soft X-ray microscopes of a large misalignment tolerance. The two-mirror anastigmat configurations were expressed by a practical variable related to pupil obstruction limiting the system throughput. Axial coma and other aberrations caused by a slight decenter of the system were then formulated to represent sensitivity to misalignment. These formulations enabled a global survey of solution groups as demonstrated by a designing example of soft X-ray microscopes with a magnification m = −1/50, which resulted in four solutions more insensitive to misalignment than a standard Schwarzschild optics in the soft X-ray region. Some solutions were also found to have much larger fields of view suitable for high resolution imaging as confirmed by computer ray tracing.     

Investigation of the Doughnut Effect in Cy3-Labeled Protein Microarrays using Scanning Near-Field Optical Microscope

We demonstrate the fluorescence mapping of protein microarrays by the technique of scanning near-field optical microscopy (SNOM) and confocal microscopy. Micron sized spots (300 μm) of human Immunoglobulin G (hIgG) protein with and without a Cy3 dye labeling have been fabricated on glass substrates by an immobilization method which makes use of calixcrown derivatives termed Prolinker. We have also tried to probe into the well-known “doughnut effect” observed in fluorescence images of proteins using the SNOM technique. The topographic and fluorescence SNOM images revealed that the number of proteins at the boundary of the spot were more than at the center in the case of the microarray spot which showed brighter luminescence at the edge than at the center in the confocal image.     

Observation of baker’s yeast strains used in biotransformation by atomic force microscopy

Different strains of baker’s yeast(Saccharomyces cerevisiae) were imaged with an atomic force microscope (AFM). The images of uncoated and nonfixed samples were reproducible with high-constrast and nanometer-resolution. Molecules from the polysaccharide surface of the cell wall were pictured and the distance of atoms was measured. The preparation of samples was easy, suggesting that AFM is a useful tool in this type of analyses.     

脱乙酰基对天然魔芋葡甘聚糖分子形貌的影响

通过原子力显微镜直接观察魔芋葡甘聚糖（KGM）分子的三维结构形貌，KGM水溶液铺展在经Ca^2 处理的云母片上，干燥固定后，可获得稳定，重复的图像，实验结果表明，稀溶液中KGM分子具有伸展的螺旋链状结构，单股的长度达200－400nm，厚度为1．0nm，宽度为35．0－35．2nm，脱乙酰后分子链卷曲成直径约40－50nm,厚3．5－5．0nm的弹性圆台状。     

Solid-state interactions and drug release of teicoplanin in binary combinations with peracetylated α-, β-, and γ-cyclodextrins

Triacetyl α-cyclodextrin, triacetyl β-cyclodextrin and triacetyl γ-cyclodextrin were tested as possible hydrophobic carriers to prolong the release of hydrophilic teicoplanin (TCP). Physical–chemical characterization of individual components, drug-carrier physical mixtures at 0.5, 0.67 and 0.75 mass fraction of carrier, and the respective interaction products by kneading or evaporative crystallization under microwave irradiation was carried out using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In vitro drug release in pH 7.4 phosphate buffer at 37 °C was determined by intrinsic dissolution rate (IDR) measurements on non disintegrating compressed discs. Solid-state interactions of TCP with triacetyl α-cyclodextrin by evaporative crystallization and kneading and with triacetyl β-cyclodextrin by evaporative crystallization (probably resulting in carrier amorphization) were demonstrated. The role of carrier hydrophobicity, carrier mass fraction and preparation method of solid drug-carrier combinations on solid-state drug-carrier interactions and slowing down of TCP release was assessed. Modulation of drug release can be achieved using TCP-triacetyl γ-cyclodextrin combinations at 0.5 mass fraction of carrier.     

Macroporous poly(methyl methacrylate) produced by phase separation during polymerisation in solution

Polymethyl methacrylate (PMMA) sponges were obtained by polymerization in a solution with monomer/ethanol ratios up to 20:80. The material obtained after the elimination of the solvent present a homogeneous distribution of dispersed pores up to a monomer/ethanol ratio lower than 40:60. For higher ethanol contents in the reacting mixture, the morphology of the sponge corresponds to a network of PMMA microparticles, leaving large empty spaces leading to highly porous structure. The monomer/ethanol ratio during polymerization has a large influence on the porosity, thermal, and mechanical properties of the material and, for large solvent contents, on the size of the polymer microparticles.