Microstructural and mechanical analysis of Cu and Au interconnect on various bond pads

Effects of High Temperature Storage (HTS) and bonding toward microstructure change of intermetallic compound (IMC) at the wire bonding interface of 3 types of bond pad (Al, AlSiCu and NiPdAu) were presented in this paper. Optical and electron microscope analyses revealed that the IMC growth rate of samples under 175 and 200 °C HTS increased in the order of Al > AlSiCu > NiPdAu. Besides, higher HTS and bonding temperatures also promoted higher IMC thickness. The compositional study showed that higher HTS and bonding temperature developed rapid interdiffusion in bonding interface. In the mechanical ball shear test, a decrease of the shear force of Al and AlSiCu bond pads after 500 h HTS was believed due to poorly developed IMC at bonding interface. On the other hand, shear force degradation at 1000 h was due to excessive growth of IMC that in turn causes the formation of defects. For NiPdAu bond pad, increasing trend of shear force with HTS duration at 175 °C implied a good reliability of the Cu wire bonding. The rapid microscopic inspection on Cu wired Al bond pad under HTS 175 °C showed the IMC development from the periphery to the center of the ball bond. However, after 500 h voids started to develop until the crack was observed at 1000 h.     

Siloxane polymers containing azo moieties synthesized by click chemistry for photo responsive and liquid crystalline applications

Three new types of siloxane‐based photoactive liquid crystalline polymers containing azo side groups were synthesized through the click chemistry route. The polymers having molecular weight range of 14,000–34,000 g mol^?1 were soluble in most of the polar solvents like chloroform, tetrahydrofuran, dimethylformamide, dimethyl sulfoxide, and dichloromethane. The photoresponsive trans–cis photoisomerization under UV radiation and cis–trans relaxation process in dark for the polymers were studied. The isomerization rate constants were found to be 0.01–0.04 sec^?1 and 1.16*10^?4–4.67*10^?4 sec^?1, respectively. It has been noted that the polymers showed high intensity absorption for n‐π* in chloroform. Both trans and cis forms of azide monomers having azo moiety exhibited molar extinction coefficient ( ? _max) in the range of 22,000–33,000 L mol^?1 cm^?1. The thermotropic behavior of the polymers was studied by polarizing optical microscope (POM) and differential scanning calorimetry (DSC) experiments. Polymer P1 showed liquid crystalline textures of nematic droplets, whereas P2 showed smectic focal conic texture and nematic droplets. Polymer P1 was also studied for photomechanical bending on exposure to UV radiation. The polymers showed initial degradation temperature in the range of 210–275°C. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Click chemistry‐based synthesis of azo polymers for second‐order nonlinear optics

Four linear polymers containing pendant azo moiety were synthesized through click chemistry for second‐order nonlinear optical study. The polymers were found soluble in most of the polar organic solvents such as tetrahydrofuran (THF), chloroform, and dimethyl formamide (DMF). The polymers showed thermal stability up to 300 °C and glass transition temperatures (T_g) in the range of 120–140 °C. The molecular weights (M_w) of these polymers (measured by gel permeation chromatography) were in the range 37,900–55,000 g/mol. The polymers were found to form optically transparent films by solution casting from THF solution. Order parameters were calculated from UV–vis absorption spectra. The morphology changes in the films after poling were characterized by atomic force microscopy. The angular dependence, temperature dependence, and time dependence of second harmonic generation (SHG) intensity were obtained by using 1064 nm Nd:YAG laser. The SHG intensity remained unchanged up to 95 °C. At room temperature, it remained stable up to 8 days after initial drop of about 14%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Improving charge transport in poly(3‐hexylthiophene) transistors via blending with an alkyl‐substituted phenylene–thiophene–thiophene–phenylene molecule

A prototypical semiconducting bicomponent system consisting of a conjugated polymer, that is, poly(3‐hexylthiophene) (P3HT), blended with a small thiophene containing conjugated molecule, that is, an alkyl‐substituted bisphenyl‐bithiophene [phenylene–thiophene–thiophene–phenylene (PTTP)], has been used as an electroactive active layer in field‐effect transistors (FETs). The self‐assembly of this bicomponent system at surfaces has been studied at different length scales, from the nanoscale to the macroscale, and compared with the behavior of monocomponent films of PTTP and P3HT. The correlation between morphology and electric properties of the semiconducting material is explored by fabricating prototypes of FETs varying the relative concentrations of the two‐component blend. The maximum charge carrier mobility value, achieved with a few percent of PTTP component, is not simply due to a uniform dispersion of the molecules in the polymer matrix, but rather to the generation of very long percolation paths, whose composition and electrical properties can be tuned with the PTTP concentration. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Bio‐based comb‐like copolymers derived from alkyl 10‐undecenoates and maleic anhydride

In this article, 10‐undecenoic acid, based on castor oil, was used a raw material for the synthesis of alternating copolymers. ω‐Unsaturated fatty esters as alkyl 10‐undecenoates were prepared by the esterification reaction of 10‐undecenoic acid with alkyl alcohol. A series of comb‐like copolymers were synthesized by free radical polymerization from maleic anhydride and alkyl 10‐undecenoates copolymers with different length of alkyl side chains in a toluene solution. These copolymers were investigated by ¹H and ¹³C nuclear magnetic resonance, Fourier transform infrared spectroscopy, gel permeation chromatography, thermogravimetric analysis, differential scanning calorimetry (DSC). The copolymers were obtained in a low molecular weight in a range 3370–12,240 g mol⁻¹ and their structural characterization indicated the formation of alternating copolymers. DSC characterization revealed that these comb‐like copolymers showed amorphous to semicrystalline behavior by increasing the length of side chains. The bio‐based comb‐like copolymers allow for the development of new polymeric materials for several applications. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1039–1045     

Silicon‐containing trifunctional and tetrafunctional cyanate esters: Synthesis,cure kinetics,and network properties

The synthesis and physical properties of new silicon‐containing polyfunctional cyanate ester monomers methyl[tris(4‐cyanatophenyl)]silane and tetrakis(4‐cyanatophenyl)silane, as well as polycyanurate networks formed from these monomers are reported. The higher crosslinking functionality compared to di(cyanate ester) monomers enables much higher ultimate glass transition temperatures to be obtained as a result of thermal cyclotrimerization. The ability to reach complete conversion is greatly enhanced by cocure of the new monomers with di(cyanate ester) monomers such as 1,1‐bis(4‐cyanatophenyl)ethane. The presence of silicon in these polycyanurate networks imparts improved resistance to rapid oxidation at elevated temperatures, resulting in char yields as high as 70% under nitrogen and 56% in air in the best‐performing networks. The water uptake in the silicon‐containing networks examined is 4–6 wt % after 96 h of immersion at 85 °C, considerably higher than both carbon‐containing and/or di(cyanate ester) analogs. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 767–779     

Simple laser vision sensor calibration for surface profiling applications

Due to the relatively large structures in the Oil and Gas industry, original equipment manufacturers (OEMs) have been implementing custom-designed laser vision sensor (LVS) surface profiling systems as part of quality control in their manufacturing processes. The rough manufacturing environment and the continuous movement and misalignment of these custom-designed tools adversely affect the accuracy of laser-based vision surface profiling applications. Accordingly, Oil and Gas businesses have been raising the demand from the OEMs to implement practical and robust LVS calibration techniques prior to running any visual inspections. This effort introduces an LVS calibration technique representing a simplified version of two known calibration techniques, which are commonly implemented to obtain a calibrated LVS system for surface profiling applications. Both calibration techniques are implemented virtually and experimentally to scan simulated and three-dimensional (3D) printed features of known profiles, respectively. Scanned data is transformed from the camera frame to points in the world coordinate system and compared with the input profiles to validate the introduced calibration technique capability against the more complex approach and preliminarily assess the measurement technique for weld profiling applications. Moreover, the sensitivity to stand-off distances is analyzed to illustrate the practicality of the presented technique.     

Mechanistic aspects on molecular structure formation of polymeric networks from diisocyanates with amidine compounds

Polymeric networks are produced by step‐growth polyaddition and co‐polyaddition reactions of 1‐ethylimidazoline in combination with various diisocyanates. Five aromatic, two aliphatic diisocyanates and a polyurethane prepolymer are used as particular reactant in N,N‐dimethylformamide as solvent at room temperature. Obviously, 1‐ethylimidazoline can serve as trifunctional monomer, which enables a crosslinking reaction with diisocyanates. Molecular structure elements of the polymeric networks were studied by solid state 13C‐NMR spectroscopy revealing that detailed molecular structure formations are determined whether aromatic or aliphatic diisocyanates are used. Quantum chemical calculations were used as supporting method to elucidate the complex reaction cascades. Hence, it can be shown that beside 3:1 stoichiometric structures 2:1 based structures are formed as well. These structures are observed as kinetically controlled products only when aromatic diisocyanate monomers are used. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 977–985     

JEM-2100PLUS透射电子显微镜操作方法与技巧及常见故障排除

以JEM-2100PLUS透射电子显微镜为例，介绍了电镜的基本结构、操作面板和成像原理。使用透射电子显微镜的最终目的就是要得到高质量的照片，结合透射电镜的操作步骤，总结了如何拍摄高质量的照片以及常见故障排除方法。