On the optimization of higher eigenvaluesSur l'optimisation de valeurs propres supérieures

A new approach is proposed for the study of the classical Lagrange problem on the optimal form of a column with clamped ends and a fixed volume. It is proved that there exists a column with the maximal possible value of the kth eigenvalue and that such a column is unique. A method for the numerical solution is proposed. The method is based on the analysis of the critical points of a non-linear functional related to the Lagrange problem. To cite this article: Y.V. Egorov, C. R. Mecanique 332 (2004).     

Écoulement turbulent dans une cavité rotor–stator fermée de grand rapport d'aspect

A direct numerical simulation is combined with laboratory study to describe the turbulent flow in an annular high speed rotor–stator cavity. Comparisons are made for a turbulent flow characterized by a Reynolds number $\mathit{Re}=\Omega R_2^2/\nu =9.5\times {10}^4$ in a shrouded cavity of large aspect ratio $G=(R_2?R_1)/h=18.32$, where $R_1$ and $R_2$ are the inner and outer radii of the rotating disk, and h is the inter-disk space. A close agreement is found between the computed results and the experimental data for the mean and turbulent fields.? To cite this article: S. Poncet, A. Randriamampianina, C. R. Mecanique 333 (2005).     

Modélisation et simulation numérique du changement de phase liquide–vapeur en cavitéModeling and numerical simulation of liquid–vapor phase change in an enclosed cavity

A model for the simulation of boiling flow with phase change in a closed cavity is presented. A front-tracking method is used to deal with the liquid–vapor interface. The liquid phase is incompressible while the vapor phase is weakly compressible and obeys to the perfect gas law. This model can deal with large density ratio (${\rho }_l/{\rho }_v?1000$) flows while accounting for the saturation curve. Computations are performed on a 1D validation case, idealizing a pressure cooker. Results are compared with a low Mach number approximation. To cite this article: V. Daru et al., C. R. Mecanique 334 (2006).     

Identification of the convective instability in a multi-component solution by 3D simulations

Three-dimensional calculations have been done to simulate the onset of convective motion in ternary nondilute solution under phase transition conditions. The process is considered for Rayleigh number in the range $[1\times {10}^3,1.4\times {10}^4]$, where subcritical convective motion with hexagonal flow pattern is identified. The results are in good agreement with the linear and finite amplitude theory of hydrodynamics instability. To cite this article: V.V. Kolmychkov et al., C. R. Mecanique 333 (2005).     

Détermination de la réponse asymptotique d'une structure anélastique sous chargement thermomécanique cycliqueDetermination of the asymptotic response of a structure under cyclic thermomechanical loading

A method for the solution of cyclic thermomechanical nonlinear problems is presented: it is a Direct Cyclic Method which is an alternative approach to classical methods. It consists in directly seeking the asymptotic response of an inelastic structure subjected to a periodic thermomechanical loading without following the loading path. It is based on the Large Time Increment Method, the periodicity of the limit state and the Fourier transform. To cite this article: M.H. Maitournam et al., C. R. Mecanique 330 (2002) 703–708.     

A dissipation-based control method for the multi-scale modelling of quasi-brittle materials

Multi-scale models based on computational homogenisation are nowadays developed for the simulation of complex material behaviour. The use of homogenisation techniques on finite-sized representative volume elements in the presence of quasi-brittle damage may lead to the presence of snap-backs in the macroscopic material response. A methodology to simulate this type of response in the multi-scale technique is proposed, based on the control of the dissipation at the mesoscopic scale. To cite this article: T.J. Massart et al., C. R. Mecanique 333 (2005).     

Motion of a porous sphere in a spherical container

The creeping motion of a porous sphere at the instant it passes the center of a spherical container has been investigated. The Brinkman's model for the flow inside the porous sphere and the Stokes equation for the flow in the spherical container were used to study the motion. The stream function (and thus the velocity) and pressure (both for the flow inside the porous sphere and inside the spherical container) are calculated. The drag force experienced by the porous spherical particle and wall correction factor is determined. To cite this article: D. Srinivasacharya, C. R. Mecanique 333 (2005).     

Random-field model for the elasticity tensor of anisotropic random media

This Note deals with the construction of a non-Gaussian positive definite matrix-valued random field whose mathematical properties allow the fourth-order elasticity tensor of random non homogeneous anisotropic three dimensional elastic media to be modelled. If the usual parametric probabilistic approach was used, then 21 mutually dependent random fields should be modelled and identified by using experimental data. Such an approach would be very difficult because the systems of the marginal probability distributions of these random fields have to be identified due to the fact that, for a boundary value problem, the displacement field of the random medium is a non-linear mapping of the random elasticity tensor. The theory presented in this paper allows such a probabilistic model of the fourth-order elasticity tensor field to be constructed and depends only of four scalar parameters: three spatial correlation lengths and one parameter allowing the level of the random fluctuations to be controlled. To cite this article: C. Soize, C. R. Mecanique 332 (2004).

Résumé

On présente la construction d'un champ aléatoire à valeurs dans les matrices définies positives dont les propriétés mathématiques permettent de modéliser le tenseur d'élasticité du quatrième ordre des mileux élastiques anisotropes tridimensionnels aléatoires. Si l'approche probabiliste paramétrique usuelle était utilisée, alors il serait nécessaire de modéliser et d'identifier à l'aide de données expérimentales 21 champs aléatoires mutuellement dépendants. Une telle approche serait très difficile de part le fait que le système de lois marginales de ces champs aléatoires doit être identifié parce que, pour un problème aux limites, le champ de déplacement est une transformation non linéaire du tenseur d'élasticité. La théorie présentée dans ce papier permet de construire une modélisation probabiliste du champ de tenseur d'élasticité qui ne dépend que de quatre paramètres scalaires : trois échelles de corrélation spatiale et un paramètre permettant de contrôler le niveau des fluctuations aléatoires. Pour citer cet article : C. Soize, C. R. Mecanique 332 (2004).     

Second-order estimates for the large-deformation response of particle-reinforced rubbersEstimations homogénéisées pour le comportement mécanique des caoutchoucs renforcés en grandes déformations

This paper presents the application of a recently proposed ‘second-order’ homogenization method (J. Mech. Phys. Solids 50 (2002) 737–757) to the estimation of the effective behavior of hyperelastic composites subjected to finite deformations. The main feature of the method is the use of ‘generalized’ secant moduli that depend not only on the phases averages of the fields, but also on the phase covariance tensors. The use of the method is illustrated in the context of particle-, or fiber-reinforced elastomers and estimates analogous to the well-known Hashin–Shtrikman estimates for linear-elastic composites are generated. The new estimates improve on earlier estimates (J. Mech. Phys. Solids 48 (2000) 1389–1411) neglecting the use of fluctuations. In particular, the new estimates, unlike the earlier ones, are capable of recovering the exact incompressibility constraint when the matrix is also taken to be incompressible. To cite this article: O. Lopez-Pamies, P. Ponte Castañeda, C. R. Mecanique 331 (2003).     

Optimal design of functionally graded plates with thermo-elastic plastic behaviourConfiguration optimale des plaques fonctionnellement graduées à plasticité thermo-élastique

The thermo-elastic plastic behaviour of functionally graded plates under extremal thermal loading at different boundary conditions is considered. The plates consist of two phases – ZrO₂ ceramics and Ti₆Al₄V alloy. The layers are distributed exponentially through the thickness. The mechanical and thermal properties of both materials strongly depend on temperature. The stress–strain behaviour is investigated by the FEM. To predict the stable state of the structures of interest, several failure criteria are applied. Two cost functions are introduced to optimize the design of the plate. The main results are discussed and graphically illustrated. To cite this article: L. Parashkevova et al., C. R. Mecanique 332 (2004).