New figuring model based on surface slope profile for grazing‐incidence reflective optics

Surface slope profile is widely used in the metrology of grazing‐incidence reflective optics instead of surface height profile. Nevertheless, the theoretical and experimental model currently used in deterministic optical figuring processes is based on surface height, not on surface slope. This means that the raw slope profile data from metrology need to be converted to height profile to perform the current height‐based figuring processes. The inevitable measurement noise in the raw slope data will introduce significant cumulative error in the resultant height profiles. As a consequence, this conversion will degrade the determinism of the figuring processes, and will have an impact on the ultimate surface figuring results. To overcome this problem, an innovative figuring model is proposed, which directly uses the raw slope profile data instead of the usual height data as input for the deterministic process. In this paper, first the influence of the measurement noise on the resultant height profile is analyzed, and then a new model is presented; finally a demonstration experiment is carried out using a one‐dimensional ion beam figuring process to demonstrate the validity of our approach.     

Generating Metallic Amorphous Core–Shell Nanoparticles by a Solid‐State Amorphization Process

Metallic crystalline/amorphous core–shell nanoparticles consisting of a crystalline Pd core (c‐Pd) surrounded by an amorphous Fe₂₅Sc₇₅ shell (a‐FeSc) are prepared by inert‐gas condensation. A phase transformation of the c‐Pd by a solid‐state diffusion process resulting in an amorphous core (a‐PdSc) surrounded by an amorphous FeSc shell is observed if the core–shell structure is irradiated at ambient temperature with 300 keV electrons. The amorphization process seems to involve the diffusion of irradiation‐induced defects and is presumably driven by the large negative heat of mixing of Pd and Sc, as well as by the excess enthalpy of the interfaces between the c‐Pd regions and the surrounding a‐FeSc. The structural transformation reported here opens a new way to producing metallic amorphous core–shell nanoparticles of different chemical compositions and probably novel properties.     

时滞速度反馈作用下弹性梁的主共振分析

采用时滞速度反馈控制策略对轴力作用下的弹性梁进行振动控制.根据Newton第二定律建立压电耦合弹性梁的非线性振动控制模型,运用直接法得到时滞反馈作用下弹性梁主共振的一阶近似解,得出系统响应与控制参数的关系.结果表明,主共振的响应存在多解和跳跃现象,调节控制增益和时滞值可以有效抑制大幅振动.     

JRQ and JPA irradiated and annealed reactor pressure vessel steels studied by positron annihilation

The paper is focused on a comprehensive study of JRQ and JPA reactor pressure vessel steels from the positron annihilation lifetime spectroscopy (PALS) point of view. Based on our more than 20 years’ experience with characterization of irradiated reactor steels, we confirmed that defects after irradiation start to grow and/or merge into bigger clusters. Experimental results shown that JPA steel is more sensitive to the creation of irradiation-induced defects than JRQ steel. It is most probably due to high copper content (0.29?wt.% in JPA) and copper precipitation has a major impact on neutron-induced defect creation at the beginning of the irradiation. Based on current PALS results, no large vacancy clusters were formed during irradiation, which could cause dangerous embrittlement concerning operation safety of nuclear power plant. The combined PALS, small angle neutron scattering and atomic probe tomography studies support the model for JRQ and JPA steels describing the structure of irradiation-induced clusters as agglomerations of vacancy clusters (consisting of 2–6 vacancies each) and are separated from each other by a distribution of atoms.     

偏振分光光学天线前向散射杂光仿真测试与抑制

利用口径150mm、视场±0.17°、接收波长974nm的光学天线望远系统原理样机,搭建了试验装置并进行了实测,测量结果显示光学天线在0.35°附近及1°附近出现了两个原路回波杂光峰值.通过对两个杂光峰值的仿真分析,提出了在主镜内部增加二次斜光阑及临时挡光环的措施,消除望远系统前向散射杂光.通过分析主次镜焦距分配对光学天线望远系统杂光的影响,指出在设计中缩小主镜焦距可降低系统原路回波杂光,这对光学天线消回波杂光设计具有指导意义.     

部分相干光在大气湍流中的到达角起伏

研究了部分相干高斯谢尔光束在大气湍流中的到达角起伏.主要采用湍流内外尺度的修正Von Karmon谱模型及广义惠更斯-菲涅尔原理和交叉谱密度函数推导出了部分相干光在大气湍流中的到达角起伏表达式.对比分析了湍流内外尺度、湍流强度、传输距离、源相干参数以及波长等参数对部分相干光在大气湍流水平路径上传输时的到达角起伏的影响.结果表明:随着传输距离的增加,到达角起伏越来越小;随着大气湍流内外尺度和源相干参数的增加,到达角起伏也越来越大;与部分相干光相比,完全相干光的到达角起伏受湍流影响很小;随着波长和湍流强度的减小,到达角起伏越来越小.     

不同LET碳离子束辐照拟南芥干种子的当代损伤效应

本研究以拟南芥（Columbia野生型）干种子为材料,利用兰州重离子研究装置（HIRFL）产生的碳离子束对材料进行辐射处理,统计其存活率、根长、下胚轴长及每果荚种子数,以探讨不同传能线密度（Linear Energy Transfer,LET）的碳离子束辐照对拟南芥当代损伤效应的影响。结果表明,在相同LET辐射条件下,随着辐射剂量的增大,拟南芥的存活率、根长、下胚轴长度、每果荚种子数都呈现下降趋势。在相同剂量不同LET辐射处理情况下,随着LET的增大,存活率、根长、下胚轴长、每果荚种子数都显著下降,可见高LET辐射严重抑制了拟南芥的生长和发育。研究表明,当LET为50 keV/μm时,碳离子束辐射拟南芥干种子对应的最佳诱变剂量为200 Gy,为后续开展碳离子束辐射的诱变效率研究奠定了前期基础。Aimed to study the biological effects of carbon ion beams with different linear energy transfer (LET) values provided by Heavy Ion Research Facility in Lanzhou (HIRFL), dry seeds of Arabidopsis thaliana (Columbia-WT) were irradiated and a series of biological effects of postembryonic development, such as survival rate, primary root length, hypocotyls length and number of seeds per silique, were investigated. The results showed that, under the radiation condition of the same LET value, the survival rate, root length, hypocotyls length and number of seeds per silique were decreased with the increasing dose. In addition, under the radiation conditions with different LET values, but same dose, the extent of the decline of the survival rate, root length, hypocotyls length and number of seeds per silique were reinforced with the increasing LET. It was also found that high LET radiations inhibited the subsequent growth and development of Arabidopsis thaliana severely. In brief, it was suggested that the optimum dose of carbon ion beam with 50 keV/μm value on Arabidopsis thaliana dry seeds was 200 Gy. This research complemented the preliminary theoretical foundation for the comparative study of the highest mutation efficiency of carbon ion beam irradiations at IMP, CAS(Institute of Modern Physics, Chinese Academy of Sciences).     

高压熔渗生长法制备金刚石聚晶中碳的转化机制研究

在6 GPa和1500 ℃的压力和温度范围内, 利用高压熔渗生长法制备了纯金刚石聚晶, 深入研究了高温高压下金刚石聚晶生长过程中碳的转化机制. 利用光学显微镜、X-射线衍射、场发射扫描电子显微镜检测, 发现在熔渗过程中金刚石层出现了石墨化现象, 在烧结过程中金刚石颗粒表面形貌发生了变化. 根据实验现象分析, 在制备过程中存在三种碳的转化机制: 1)金属熔渗阶段金刚石颗粒表面石墨化产生石墨; 2)产生的石墨在烧结阶段很快转变为填充空隙的金刚石碳; 3)金刚石直接溶解在金属溶液中, 以金刚石形式在颗粒间析出, 填充空隙. 本文研究碳的转化机制为在高温高压金属溶剂法合成金刚石的条件下(6 GPa和1500 ℃的压力和温度范围内)工业批量化制备无添加剂、无空隙的纯金刚石聚晶提供了重要的理论指导.     

含有AlGaAs插入层的InAs/GaAs三色量子点红外探测器

本文报道了采用分子束外延技术制备的三色InAs/GaAs量子点红外探测器. 器件采用nin型结构, 吸收区结构是在InGaAs量子阱中生长含有AlGaAs插入层的InAs量子点, 器件在77 K下的红外光电流谱有三个峰值: 6.3, 10.2和11 μm. 文中分析了它们的跃迁机制, 并且分别进行了指认. 因为有源区采用了不对称结构, 所以器件在外加偏压正负方向不同时, 光电流谱峰值的强度存在一些差异. 不论在正偏压或者负偏压下, 当偏压达到较高值, 再进一步增大偏压时, 都出现了对应于连续态的跃迁峰强度明显下降的现象, 这是由量子点基态与阱外连续态的波函数交叠随着偏压进一步增大而迅速减小导致的.     

气源分子束外延生长的InPBi薄膜材料中的深能级中心

利用深能级瞬态谱(DLTS)研究了气源分子束外延(GSMBE)生长的InP1-xBix材料中深能级中心的性质。在未有意掺杂的InP中测量到一个多数载流子深能级中心E1,E1的能级位置为Ec-0.38 e V,俘获截面为1.87×10~(-15)cm~2。在未有意掺杂的InP0.9751Bi0.0249中测量到一个少数载流子深能级中心H1,H1的能级位置为Ev+0.31 eV,俘获截面为2.87×10~(-17)cm~2。深中心E1应该起源于本征反位缺陷PIn,深中心H1可能来源于形成的Bi原子对或者更复杂的与Bi相关的团簇。明确这些缺陷的起源对于InPBi材料在器件应用方面具有重要的意义。