Stability of longitudinally corrugated cylindrical shells under uniform surface pressure

The buckling problem for longitudinally corrugated cylindrical shells under external pressure is solved. The solution makes practically exact allowance for the geometry and buckling modes of the shell. The inaccuracy of the results is due to the assumption that the subcritical state is momentless. Shells consisting of cylindrical panels of smaller radius and noncircular shells with sinusoidal corrugations are analyzed for stability. The practical applicability of such shells is demonstrated __________ Translated from Prikladnaya Mekhanika, Vol. 43, No. 11, pp. 66–79, October 2007.     

Supersonic flow past a wedge on a flat plate. Laminar boundary layer separation and reattachment

Supersonic laminar flow past a two-dimensional “flat-plate/wedge“ configuration is numerically investigated. The pressures at the boundary layer separation and reattachment points are calculated over wide Mach and Reynolds number ranges. The minimum angles of the wedge surface inclination at which a return flow occurs are determined. The results are presented in the form of generalized Mach-number-dependences of the theoretical pressure on the wedge surface initiating boundary layer separation and the pressure at the boundary layer reattachment point.     

Liquid single- and gas—liquid two-phase flows of magnetic fluid in the presence of a high non-uniform parallel magnetic field

The effect of a non-uniform parallel high magnetic field on flow control characteristics is investigated experimentally for a magnetic fluid single-phase flow and an air—magnetic fluid two-phase flow in a vertical channel. It is found that as the magnetic field strength is increased, the friction factor of the single-phase flow increases significantly. For the two-phase flow, the friction pressure loss and the head pressure loss, which is smaller than the friction loss, are negligibly small compared with the magnetic pressure loss. In the case where air is injected 27.9d upstream from the maximum magnetic field, the air flow is blocked by the magnetic force in the entrance of the magnetic field, which leads to increases in both local void fraction and pressure drop there. In the case where air is injected 1.43d downstream from the maximum magnetic field, the air flow is accelerated, resulting in a decrease in void fraction and an increase in pressure rise. In the latter case and under the present range of experimental conditions, the magnetic pumping head reaches 0.02 MPa at the highest, and the maximum circulation flow rate reaches twice as high as non-magnetically driven flow rate.     

Phase structure change and ER effect in liquid crystalline polymer/dimethylsiloxane blends

The mechanism of the electrorheological (ER) effect in two types of liquid crystalline polymer (LCP)/dimethylsiloxane (DMS) blends was investigated by rheological measurements and by structure observation under electric field and shear flow. The results show that the phase structures of these immiscible blends can be categorized into slipping (low viscosity) and non-slipping (high viscosity) states. In the non-slipping state, higher viscosity LCP domains connect the electrodes. In the slipping state, on the other hand, LCP domains do not connect the electrodes and the shear is mainly confined in the lower viscosity DMS domains. The ER effect (electrically induced viscosity increase) originates from the electrically induced slipping to non-slipping transition. In one of the blends, the ER effect occurs only at high shear rate, since this blend is in non-slipping state even under no field if the shear rate is low. Received: 29 April 1997 Accepted: 3 November 1997     

岩石（煤）的碎胀与压实特性研究

本文通过自行设计的一套岩石（煤）的松散和压实试验方案及相应的实验设备，对兖州矿区岩（煤）样进行了较为系统的碎胀与压实特性研究，测定了岩石（煤）的碎胀系数、碎胀曲线、压实曲线和侧压曲线．     

软粘土卸载特性计算模型研究

本文从三个方面对软粘土的卸载特性进行了理论研究。采用太沙基一维固结理论，编制了内嵌固结计算的修正剑桥模型程序．对软粘土卸载强度进行了分析。推导了基于修正剑桥模型的孔压表达式并编制了相应的程序对软粘土的卸载孔压特性进行了研究，结果显示，在伸长条件下．孔压先由零逐渐发展到负的最大值．然后又逐渐减小至零。突破零位后，发展成为正孔压并最后达到正的最大值。围压越大，产生的负孔压的极值越大，最终的正孔压越小。将传统边界面模型的线弹性卸载过程改进为弹塑性．建立了软粘土的边界面广义弹塑性模型，从而使边界面模型可用于分析软粘土卸载过程中的塑性变形问题。理论分析结果与试验进行了比较验证，证明理论研究方法是可行的。     

Kinetics of microcrack blunting ahead of macrocrack approaching shear wave speed

The fracturing of glass and tearing of rubber both involve the separation of material but their crack growth behavior can be quite different, particularly with reference to the distance of separation of the adjacent planes of material and the speed at which they separate. Relatively speaking, the former and the latter are recognized, respectively, to be fast and slow under normal conditions. Moreover, the crack tip radius of curvature in glass can be very sharp while that in the rubber can be very blunt. These changes in the geometric features of the crack or defect, however, have not been incorporated into the modeling of running cracks because the mathematical treatment makes use of the Galilean transformation where the crack opening distance or the change in the radius of curvature of the crack does not enter into the solution. Change in crack speed is accounted for only via the modulus of elasticity and mass density. For this simple reason, many of the dynamic features of the running crack have remained unexplained although speculations are not lacking. To begin with, the process of energy dissipation due to separation is affected by the microstructure of the material that distinguishes polycrystalline from amorphous form. Energy extracted from macroscopic reaches of a solid will travel to the atomic or smaller regions at different speeds at a given instance. It is not clear how many of the succeeding size scales should be included within a given time interval for an accurate prediction of the macroscopic dynamic crack characteristics. The minimum requirement would therefore necessitate the simultaneous treatment of two scales at the same time. This means that the analysis should capture the change in the macroscopic and microscopic features of a defect as it propagates. The discussion for a dual scale model has been invoked only very recently for a stationary crack. The objective of this work is to extend this effort to a crack running at constant speed beyond that of Rayleigh wave. Developed is a dual scale moving crack model containing microscopic damage ahead of a macroscopic crack with a gradual transition. This transitory region is referred to as the mesoscopic zone where the tractions prevail on the damaged portion of the material ahead of the original crack known as the restraining stresses, the magnitude of which depends on the geometry, material and loading. This damaged or restraining zone is not assumed arbitrarily nor assumed to be intrinsically a constant in the cohesive stress approach; it is determined for each step of crack advancement. For the range of micronotch bluntness with 0 < β < 30° and 0.2 σ_∞/σ₀ 0.5, there prevails a nearly constant restraining zone size as the crack approaches the shear wave speed. Note that β is the half micronotch angle and the applied stress ratio is σ_∞/σ₀ with σ₀ being the maximum of the restraining stress. For σ_∞/σ₀ equal to or less than 0.5, the macrocrack opening displacement COD is nearly constant and starts to decrease more quickly as the crack approaches the shear wave speed. For the present dual scale model where the normalized crack speed v/c_s increases with decreasing with the one-half microcrack tip angle β. There prevails a limit of crack tip bluntness that corresponds to β 36° and v/c_s 0.15. That is a crack cannot be maintained at a constant speed if the bluntness is increased beyond this limiting value. Such a feature is manifestation of the dependency of the restraining stress on crack velocity and the applied stress or the energy pumped into the system to maintain the crack at a constant velocity. More specifically, the transitory character from macro to micro is being determined as part of the unknown solution. Using the energy density function dW/dV as the indicator, plots are made in terms of the macrodistance ahead of the original crack while the microdefect bluntness can vary depending on the tip geometry. Such a generality has not been considered previously. The macro-dW/dV behavior with distance remains as the inverse r relation yielding a perfect hyperbola for the homogeneous material. This behavior is the same as the stationary crack. The micro-dW/dV relations are expressed in terms of a single undetermined parameter. Its evaluation is beyond the scope of this investigation although the qualitative behavior is expected to be similar to that for the stationary crack. To reiterate, what has been achieved as an objective is a model that accounts for the thickness of a running crack since the surface of separation representing damage at the macroscopic and microscopic scale is different. The transitory behavior from micro to macro is described by the state of affairs in the mesoscopic zone.     

The Development of Appropriate Upscaling Procedures

Permeability upscaling should be carried out with careful attention to the nature of rock heterogeneities. While there are many large-scale features which must be taken into account, there are also important heterogeneities at the small-scale. Many sedimentary structures contain laminae at the mm–cm scale, and beds at the m-scale, which give rise to strong contrasts in permeability. We use a 2D model derived from a photo-panel of an aeolian outcrop, along with permeability measurements from a North Sea oil field, to demonstrate the effects of small-scale heterogeneity. This model is similar in size to a typical cell of a reservoir geological model. We take imaginary probe and core plug measurements from the model, average them, and compare these with the effective permeability for the model computed from a finite difference flow calculation. Although this procedure is standard practice, we show that it can lead to biased estimates of the permeabilities used in flow simulation. As an alternative we suggest using models of representative beds, and performing flow simulation to calculate effective permeabilities for both single-phase and two-phase flow.     

The effect of magnetic field on two-phase liquid metal flow

In this paper, the basic equations of two-phase liquid metal flow in a magnetic field are derived, and specifically, two-phase liquid metal MHD flow in a rectangular channel is studied, and the expressions of velocity distribution of liquid and gas phases and the ratioK ₀ of the pressure drop in two-phase MHD flow to that in single-phase are derived. Results of calculation show that the ratioK ₀ is smaller than unity and decreases with increasing void fraction and Hartmann number because the effective electrical conductivity in the two-phase case decreases. The Project is supported by the National Natural Science Foundation of China.     

本征正交分解技术在屋盖风压场重建与预测中的应用

给出利用本征正交分解(POD)对屋盖风压场进行重建和预测的研究结果.对一个双坡屋盖用同步多点压力扫描系统进行了风洞试验,根据POD技术采用前若干阶本征模态重建屋盖风压场.采用两种方案预测未布置测压点位置的风压时间序列.第一种方案中利用插值技术获得没有测压点位置的本征模态值.第二种方案对参考屋盖和需预测的新屋盖分别进行试验,结合由参考屋盖试验萃取的本征模态和由新屋盖试验的风压数据计算的主坐标,预测出新屋盖未知区域的风压时间序列.文中对风压场重建和预测的效果作了分析,而且比较了根据测量的风压数据和预测的风压数据所计算的屋盖风致响应.