基于超分子结构共掺杂纳米复合薄膜的制备与荧光特性

为改善功能分了的特性,提出一种基于金属纳米粒子-偶氮染料复合物共掺杂超分子结构功能材料的设计新方法.并依照此方法制备出复合材料,观测了其显微结构,测量了其紫外-可见光吸收,研究了该超分子结构复合体系的荧光特性.实验发现,由于金属银纳米粒子的掺杂,使得超分子结构复合体系中功能分子甲基橙在溶液态体系的荧光强度增强近5倍,而在两种不同结构(共混结构和包覆结构)的薄膜态超分子结构体系中,其荧光强度分别被猝灭15%和20%.研究结果表明,复合膜中采用超分子结构完全能够改善功能分子的特性.     

射频磁控溅射法制备薄膜电池电极的计算机模拟初步

计算机模拟仿真射频磁控溅射实验制备薄膜及离于电池电极,研究了在特定实验条件下薄膜的生长过程,并分析了影响薄膜生长的部分因素。     

中间层Re的加入对覆膜钡钨阴极性能的改善

研究了一种新型的覆膜钡钨阴极——双层膜(Os-W/Re膜)钡钨阴极.对这种新型阴极的发射性能进行了测试，重点对其老炼前后表面薄膜的微观形貌进行了分析，表明中间层Re膜的加入使覆膜钡钨阴极的性能得到了改善.通过对Os-W双元合金膜钡钨阴极和Os-W/Re双层膜钡钨阴极发射特性的比较，发现Os-W/Re双层膜阴极的直流发射性能好于Os-W合金膜阴极.对两种阴极激活后发射表面的X射线光电子能谱分析表明，Os-W/Re双层膜阴极激活后表面形成的三元合金膜是其发射特性优于Os-W合金膜阴极的主要原因.应用扫描电子显微镜分析比较两种阴极激活老炼后的表面状态，结果表明：Os-W合金膜阴极在老炼一段时间后，其表面薄膜出现开裂，这会导致阴极发射均匀性下降；而Os-W/Re双层膜阴极在同样老炼条件下，发射表面薄膜均匀并保持完整，从而确保覆膜钡钨阴极发射均匀性和工作可靠性. 关键词： 双层膜钡钨阴极 Os-W/Re膜 Os-W膜 薄膜开裂     

用干涉方法测量薄膜应力

基于基片弯曲法和牛顿环的基本原理,使用He-Ne激光器、扩束镜、凸透镜和带分光镜的移测显微镜,搭建了薄膜应力测量装置.采用直流溅射法制备了厚度为30~144 nm的银薄膜,衬底采用厚度为0.15 mm、直径为18 mm的圆形玻璃片.实验发现,薄膜厚度对银薄膜的内应力有显著的影响,在薄膜厚度很小时,随着薄膜厚度的增加,应力迅速增大,达到最大值后,随着厚度的继续增加,薄膜应力下降较快并趋于稳定值.     

Assessment of thermal expansion coefficient of methylsilsesquioxane thin film

For the methylsilsesquioxane film whose optical birefringence is almost zero, it was recently reported that its vertical thermal expansion coefficient (CTE) was approximately one order of magnitude larger than the lateral CTE. Though the birefringence is not an absolute predictor of anisotropic behavior, the discrepancy in both the CTEs was so remarkable that it was essential to investigate whether the anisotropy was intrinsic property or not. If the effect of Poisson's ratio is considered in the calculation of the vertical CTE and when elastic modulus measured by surface acoustic wave spectroscopy is used in the assessment of the lateral CTE, both the CTEs are coincident with each other. Therefore, it can be concluded that the discrepancy in the CTEs can be attributed to a higher in‐plane polymer chain orientation but it can also arise from the misleadingly assumed modulus and Poisson's ratio. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3109–3120, 2006     

Photo-Absorption and photochemical decomposition of copper and alkaline-earth ß-diketonates as source gases of high-Tc superconducting films

For low-temperature deposition of oxide films relating to Bi-Sr-Ca-Cu-O superconductors, photo-absorption and -decomposition properties were examined with respect to copper and alkaline-earth ß-diketonates. It was confirmed that all ß-diketonates examined were promising as source materials for photochemical vapour deposition (photo-CVD) using a low-pressure mercury lamp, in view of their large light absorption coefficients at wavelength 254 nm. The light irradiation was effective for the formation of highly crystalline oxide films at temperatures below 600 °C. By combining two sources, Ca₂CuO₃ and SrCuO₂ films were prepared. Photo-CVD of c-axis oriented Bi₂Sr₂CuO_x film was achieved by the irradiation of ternary sources of Bi(C₆H₅)₃ and strontium and copper ß-diketonates at 500 °C.     

高温超导薄膜微波非线性研究的进展

文章介绍了高温超导薄膜微波非线性的主要特征，阐述了高温超导薄膜微波非线性产生的原因和相关的研究现状，指出了高温超导薄膜非线性研究中遇到的困难和尚未解决的问题．     

A Scanning Electron Microscopy study of water in soil

Cold stage Scanning Electron Microscopy (SEM) with a rapid cooling technique makes it possible to investigate the water phase within unsaturated porous media. It is thought that this technique preserves the main features of the micromorphology of the water menisci as it exists in the liquid phase in soils. Saddle-shaped elements, as well as pendular rings of water, were observed with concave and convex curvatures of the water-air interface. The hydraulic conductivity of an unsaturated soil may be inferred from SEM photographs. Observations of isolated water menisci indicate the existence of an immobile water domain. The surface geometry of the water menisci was analyzed quantitatively and surface tension and capillary pressure were determined.     

On the deformation and fracture of porous materials

The constitutive behavior of porous materials (including the yield loci, the void growth rate, the macro stress-strain relation and the strain to localization instability) is examined based on the lower bound approach proposed by the present authors. These results are then compared with the experimental and the finite element results as well as those predicted by Gurson's equations. Emphasis is placed on approaching the real behavior from the upper and the lower bound analysis. Calculation is also made on the influence of void nucleation on the critical strain to instability and a modified strain-controlled nucleation criterion is proposed. Finally the instability and fracture of AISI4340 steel in plane strain tension is examined and comparison is made between theoretical and experimental results.     

c轴定向氮化铝薄膜的制备

利用电子回旋共振 (ECR)微波增强化学气相沉积法 (PECVD)并使用氮气 (N2 ) ,氩气 (Ar)和AlCl3蒸气作为气源在直径为 6 .35cm的 (10 0 )单晶硅片表面制备了c轴定向氮化铝 (AlN)薄膜 ,并使用X射线衍射仪及其X射线特征能谱和扫描电镜 (SEM)分析了薄膜特征 ,研究了微波功率、基板温度和N2 流量对薄膜c轴定向的影响 ,得到了c轴偏差角小于 5°的高质量大面积AlN薄膜。