Dislocation unpinning model of acoustic emission from alkali halide crystals

The present paper reports the dislocation unpinning model of acoustic emission (AE) from alkali halide crystals. Equations are derived for the strain dependence of the transient AE pulse rate, peak value of the AE pulse rate and the total number of AE pulse emitted. It is found that the AE pulse rate should be maximum for a particular strain of the crystals. The peak value of the AE pulse rate should depend on the volume and strain rate of the crystals, and also on the pinning time of dislocations. Since the pinning time of dislocations decreases with increasing strain rate, the AE pulse rate should be weakly dependent on the strain rate of the crystals. The total number of AE should increase linearly with deformation and then it should attain a saturation value for the large deformation. By measuring the strain dependence of the AE pulse rate at a fixed strain rate, the time constantτ _s for surface annihilation of dislocations and the pinning timeτ _p of the dislocations can be determined. A good agreement is found between the theoretical and experimental results related to the AE from alkali halide crystals.     

钴（Ⅱ）—丁二酮单肟烟酰腙—亚硝酸盐体系的伏安行为及其应用

在氨性介质中(pH=9.0),钴(Ⅱ)-丁二酮单肟烟酰腙(DMNH)-亚硝酸盐体系可产生灵敏度很高的催化波。从体系的伏安行为可知,吸附于汞电极上的是混配的配盐NH_4[Co(Ⅱ)(DMNH)·(NO_2)_2],在-1.0 V(相对SCE)处,Co(Ⅱ)被还原至Co(0),DMNH被还原成自由基,由于NO_2~-的存在,自由基可参与再生反应而形成催化波。羟氨的存在可使产生催化波的最佳pH值移至8.2.用此体系进行了生物样品中钴的测定,其检出限为1×10~(-10)mol/L。     

Mössbauer studies of the re-entrant spin-glass behaviour of Fe–Al alloys

Fe–Al alloys around the concentration of 30 at. % Al present re-entrant spin-glass behaviour at low temperatures. This behaviour is not completely understood and Mössbauer spectroscopy, combined with other experimental techniques, is useful to describe and explain this behaviour. Results show that the Mössbauer spectra coincide with the magnetic behaviour showed in literature and they can be explained as a magnetic cluster system whose magnetic clusters are getting smaller when the temperature is decreasing. When the temperature is reaching to the spin-glass transition at 92 K the spins in the paramagnetic matrix are moving slower and below this transition the spins are completely frozen.     

塑料闪烁体的辐照特性

利用⁶⁰Co放射源分别对3种塑料闪烁体(BC-408, EJ-200, BC-404)进行辐照损伤研究, 比较辐照前后的透射谱、发射谱及光产额的变化, 发现3种闪烁体在低剂量具有较好的抗辐照性能; 当照射剂量超过1.44×10⁴Gy时,透射谱明显变坏, 光输出减少很严重, 但发射谱却保持不变.     

Biomagnetic measurements utilising a superparamagnetic marker: a feasibility study

Summary A preliminary study is here reported on a new potential marker for biomagnetic measurements. The marker consists of superparamagnetic polymer microspheres which were detected in the presence of external steady magnetic fields by means of an r.f.-SQUID magnetometer. The particles were prepared in samples differing in the concentration value and immersed in a homogeneous magnetic field of variable intensity. A simple model was taken into account for the distribution of the microspheres in the samples, so that the theoretical values were compared to the marker field values measured by the biomagnetic sensor. The overall sensitivity of the experimental apparatus and the minimum concentration value of the marker were then estimated.     

一类非经典扩散方程整体解的存在唯一性及长时间行为

本文讨论非经典扩散方程第一初边值问题整体解的存在唯一性及长时间行为，建立了一系列新的结果，较好地改进许多已有的结论．     

ASYMPTOTIC BEHAVIOUR OF THE SOLUTIONS OF A CERTAIN FOURTH-ORDER DIFFERENTIAL EQUATION

The present paper establishes sufficient conditions for the uniformly bounded of any solution of (1.1) and which tend to zero as t → ∞.     

承受拉-扭组合载荷的薄壁圆筒屈服时产生塑性流动的条件

提出了在无外力作功的情况下，具有Bauschinger效应的弹塑性材料处于屈服状态产生自发的塑性流动时应满足的条件．这个条件不仅与材料的力学性能有关，而且还处决于材料的具体的载荷边界条件和变形．举例说明了承受拉一扭组合的薄壁圆筒中，采用组合强化模型时，产生塑性流动的具体条件．     

受压矩形截面柱在塑性阶段的缺陷敏感性分析

对加载到塑性阶段的矩形截面柱，本文研究了几何缺陷对屈曲的影响，在分析中考虑了弹性卸载的影响，求出了荷载、缺陷大小及分叉模态幅值之间的精确渐近关系式，结果表明在塑性阶段最大承载力对小缺陷非常敏感，但当缺陷大小达到某一值后，可能不存在最大载荷。     

非球面塑料透镜注射型芯工艺探讨

本文来自于作者的实践。介绍了加工方法及测量问题。重点叙述了加工中的一些关键,同时也提供了国内外在这方面的进展情况。