Surface cavities produced by high‐dose nitrogen ion implantation into silicon

Nitrogen ion implantation (24 keV, 4.6 × 10¹⁷ cm^?2) into (100) a p‐type silicon wafer material and a subsequent electron beam annealing at 1100 °C for 15 s under high vacuum conditions leads to the formation of an uneven surface in the implanted region caused by nitrogen bubbles beneath the surface. Annealing at 1200 °C for 300 s results in surface cavities with a mean diameter of 350 nm and a surface coverage of 3–4% and an average depth of ～60 nm. Nuclear reaction analysis reveals that the nitrogen concentration in the as‐implanted state exceeds 57 at%, the value of stoichiometric Si₃N₄. Annealing at 1100 °C for 15 s slightly reduces the nitrogen peak concentration, whereas annealing at 1200 °C for 300 s induces a significant alteration to the shape of the nitrogen depth profile coupled with the lowering of the concentration close to the stoichiometry of Si₃N₄. The results present a new method of producing sub‐micrometre cavities embedded in a thin silicon nitride film on wafer silicon which may lead to novel micro‐electronic and biotechnology applications. Copyright © 2007 John Wiley & Sons, Ltd.     

双光束流动注射光度法测定生活用水中氯离子

将流动注射分析技术应用到双光束分光光度法中，对其理论和实验技术进行了研究，采用自行组装的流动注射系统进行了生活用水中氯离子的测定，获得满意结果。     

Decomposition of halogenated hydrocarbons using intense, penetrating bremsstrahlung

Radiolytic decomposition of chlorinated hydrocarbons and other toxic compounds has been experimentally measured using ionizing radiation produced by electron accelerator and nuclear isotope sources. Decomposition products have been identified. A portable, commercially available electron accelerator was set up at a Superfund site where vapor extraction wells were removing trichloroethylene (TCE) from a spill into the unsaturated soil. The extraction vapor was passed through the accelerator beam to decompose the TCE. On site radiolytic decomposition of TCE vapor using an accelerator is shown to be significantly less expensive than filtration of TCE vapor using activated charcoal.     

Design of a combined ozone/electron beam process for waste water and economic feasibility of the process

A design of a combined ozone/electron beam irradiation process for treating a 50 m³/h waste water stream from a molasses processing is discussed. Moreover, a cost evaluation of such a process in comparison to a conventional ozonation/biology treatment process has been performed to assess the potential of the irradiation process for technical use. Although the result of this comparison is not bad for the irradiation process an implementation into a full scale plant would not seem to be the thing to do in the present case.     

甲烷在Ni表面及La薄膜上激活解离化学吸附

利用分子束技术改变甲烷的平动能E_k来研究E_k及其法向分量E_n对甲烷在Ni表面及La薄膜上激活解离吸附的影响。对CH_4/Ni及CH_4/La系统, 当甲烷的平动能E_k分别低于58.5 kJ·mol~(-1)及52.3 kJ·mol~(-1)时, 没观察到甲烷的解离吸附。当甲烷的平动能超过此阈值时, 即对CH_4/Ni系统, 当Ek=58.5增至63.8 kJ·mol~(-1)时, 初始沾着几率s_0由0至0.54线性增加; 对CH_4/La系统, 当E_k=52.3增至63.8 kJ·mol~(-1)时, S_0由0至0.49线性增加。这些结果表明, 两个系统的化学吸附是不经过前趋态的直接化学吸附。最后求出CH_4/Ni, CH_4/La系统的表观活化能分别为46.8 kJ·mol~(-1)和38.1 kJ·mol~(-1)。     

Electron beam irradiated textile cellulose fibres.: ESR studies and derivatisation with glycidyl methacrylate (GMA)

Powdered samples of cotton, flax and viscose from textile fibres were subjected to electron beam irradiation (20-400 KGy). ESR signals were observed after irradiation. The intensity of the signals depended on the administered dose and exhibited an exponential decay with time. The ESR spectra, whose pattern depended drastically on the crystallinity of the samples, indicated the simultaneous presence of at least three carbon-centred radical species. When the whole irradiated textile fibres were quenched in a solution of glycidyl methacrylate (GMA) a significant increase of the weight was observed, the increase being strongly dependent on the administered dose and on the time interval elapsed between irradiation and quenching. Spectroscopic characterisation evidenced that GMA acted as cellulose radicals scavenger on the unsubstituted carbon of the double bond and was covalently linked to the fibre through a new C-C bond while maintaining unaltered the ester and the epoxide groups, available for further derivatisations. Because irradiation of the whole textile fibres in the range 20-200 KGy does not result in significant degradation of the material, GMA quenching of fibres irradiated in this dose range may represent an attractive route to their functionalisation.     

Analytical,structural and electrical characterization of SiGe layers by electron microbeam techniques

k-ratios of Ge-L and Si-K measured at different beam energies allow to evaluate simultaneously composition and thickness of SiGe layers on a Si substrate. A simple technique applying backscattered electrons also enables estimation of composition of bulk SiGe and of composition and thickness of relatively thick (200 nm) SiGe layers on Si. Electron channeling patterns of pseudomorphic SiGe/Si structures and of pure Si substrate show no significant differences whereas in relaxed structures a smearing of the pattern with increasing density of misfit dislocations is observed. Under particular conditions the technique of the electron beam induced current permits imaging of recombination-active misfit dislocations with a spatial resolution around 0.2 m. Moreover, a repulsion of holes due to the valence-band offset in a n-Si/SiGe heterostructure was detected.     

The two-dimensional Coulomb gas on a sphere: Exact results

At the special value of the reduced inverse temperature=2, the equilibrium statistical mechanics of a two-dimensional Coulomb gas confined to the surface of a sphere is an exactly solvable problem, just as it was for the Coulomb gas in a plane. The thermodynamic quantities and all the correlation functions can be calculated. Use is made of an isomorphism between the classical Coulomb gas and the free Fermi field theory associated with the Dirac operator on the sphere.Laboratory associated with the Centre National de la Recherche Scientifique.     

Mechanical properties of fiber reinforced styrene-butadiene rubbers using surface-modified UHMWPE fibers under EB irradiation

Aiming to develop a high performance fiber reinforced rubber of SBR, a special technique using electron beam (EB) irradiation-induced graft-polymerization was applied to ultra-high molecular-weight polyethylene (UHMWPE) fibers. Although UHMWPE is chemically inert, N-vinyl formamide (NVF) could be graft-polymerized onto the UHMWPE fiber surface with this special technique. A maximum grafting percentage of 23.6% was achieved. The composite of SBR and grafted UHMWPE fibers with maximum grafting indicated a linear increase in the initial modulus and strength with the fiber content. At the fiber content of 10%, the initial modulus was improved about five times with respect to that of the pure SBR, while the strength was done about twice. At this moment, only a small reduction could be observed in the strain compared with that of pure SBR. The fiber reinforced rubber with a good performance was obtained in the system of SBR and grafted UHMWPE fibers.     

Microstructural and physicochemical study of the buried Fe/AlGaAs(100) interface by transmission electron microscopy and x‐ray emission spectroscopy

Among the magnetic metal/semiconductor contacts, the Fe/GaAs system has been widely studied owing to its potential applications in electronic devices. In contrast, there are not many studies concerning the Fe/Al_xGa_1?xAs contact, and in particular there are no reports concerning the changes induced in the interfacial zone by the presence of Al. In this work, thin polycrystalline iron films were deposited by ion beam sputtering at room temperature on a 300 nm thick Al_0.25Ga_0.75As layer grown by molecular beam epitaxy onto GaAs(001). X‐ray diffraction analysis showed that the iron films are polycrystalline, and indications of a (002) texture of the film were observed. The fine scale analysis of the interface was achieved by high‐resolution transmission electron microscopy (HRTEM) observations, the results of which are compared with the physicochemical information obtained from electron‐induced x‐ray emission spectroscopy, by analysing the Al 3p valence states at the Fe/Al_xGa_1?xAs interface. The HRTEM experiments on cross‐section samples indicate that the interfacial zone between iron and AlGaAs is limited to <1.5 nm in thickness. X‐ray emission spectroscopy showed the presence of Al atoms in an FeAl‐like environment at the interface, and the existence of wrong bonds and point defects. The estimated width of the perturbed interface (2.0 ± 0.5 nm) is in agreement with the HRTEM results. Copyright © 2003 John Wiley & Sons, Ltd.