Polylactones. 13. Transesterification of Poly(L-Lactide) with Poly(Glycoude), Poly(β-Propio-Lactone), and Poly[ε -Caprolactone)

Homogeneous blends of poly(L-lactide) (M _n = 30 000 to 40 000) and poly(β-propiolactone) or poly(ε-caprolactone) were prepared in solution. The solvent-free blends were subjected to transesterification catalyzed by means of methyl triflate, triflic acid, boron trifluoride, or tributyltin methoxide at 100 or 150°C. At 100°C, transesterification was barely detectable even after 96 h. When poly(β-propiolactone) was used as the reactant at 150°C, degradation was faster than transesterification regardless of the catalyst. The same negative result was obtained for heterogeneous blends of poly(L-lactide) and poly(glycolide). In the case of poly(ε-caprolactone), copolyesters with slightly blocky sequences were obtained with tributyltin methoxide as catalyst, whereas the acidic catalysts caused rapid degradation. The copolyesters were characterized by means of ¹H-NMR spectroscopy with regard to their molar composition, by means of ¹³C-NMR spectroscopy with regard to their sequences, and by means of differential scanning calorimetry with regard to crystallinity.     

Synergic effect in electrical conductivity using a combination of two fillers in PVDF hybrids composites

The objective of this work was to prepare novel conductive blends of poly(vinylidene fluoride) (PVDF) with polypyrrole (PPy) and to compare their performance with PVDF/multiwall carbon nanotube (MWCNT) composites and novel PVDF/PPy/MWCNT hybrid systems. All the compositions were prepared by melt mixing using a miniature mixer. The mixtures were characterized by Fourier transformed infrared (FTIR), wide angle X-ray diffraction (WAXD), thermogravimetric analyses (TGA), scanning and transmission electron microscopy (SEM and TEM, respectively) and volume electrical resistivity. For the binary PVDF/PPy and PVDF/MWCNT systems, percolation thresholds of 10 and 0.3 wt%, respectively, were found. In the hybrid systems, however, the percolation threshold for each filler was lower than in the binary systems, but the electrical conductivities were always much higher at all concentrations than the conductivities of the binary systems. Therefore, the addition of both fillers had a synergistic effect on the hybrid system conductivity, which was attributed to its morphology: the PPy increased the homogeneity of the MWCNT distribution and decreased the available free volume for the MWCNT; as a result the MWCNT rolled around the PPy particles bridging them through the PVDF matrix, increasing the quantum tunneling effect and thus, the electrical conductivity of the system.     

Various ways to strengthen the fiber‐matrix interface for enhanced composite performance

Surface treatment (ST) of carbon fibers (CF) leads to an enhancement in fiber‐matrix adhesion. However, it deteriorates the strength of a fiber which makes its reinforcing action less effective in a composite. These effects in opposite directions control the net strength of a composite, and hence, the treatment has to be judiciously applied, which would enhance the first factor and minimize the second one. Authors have recently reported on four effective techniques (using various doses) such as treatments with nanoparticles of Ytterbium fluoride (YbF₃)_, cold remote nitrogen–oxygen plasma (CRNOP), γ‐ray irradiation and nitric acid oxidation. Amongst these methods, nitric acid oxidation is studied in depth in the literature, and γ‐ray irradiation is sparingly studied. However, nano‐YbF₃ and CRNOP were first time reported in the literature by the authors. However, comparative aspects of all these methods were not addressed. In this paper, these aspects in details are discussed to lay down the right criteria for selection of a ST technique of CF to design the desired performance of a composite. The composites with polyetherimide and treated CF (including untreated) were developed and evaluated for various properties including tribological one. Treated CF based composites exhibited excellent mechanical and tribological properties (under harsh operative conditions with wear rates ≈ 1 × 10^?15 m³/Nm and μ ≈ 0.09). It was concluded that for strength and tribo‐performance, different treatments and doses are to be employed. Overall nanosized‐YbF₃ treatment of CF proved to be the most promising ST method. Copyright © 2013 John Wiley & Sons, Ltd.     

微波辅助合成石墨烯/氧化镍复合材料及其表征

本文通过微波辅助的方法,快速而有效地在热膨胀石墨烯(RG)的缺陷上原位合成氧化镍纳米颗粒,形成石墨烯/氧化镍复合材料(RG/NiO)。利用X-射线衍射(XRD),拉曼光谱(Raman),傅里叶变换红外(FTIR),扫描电镜(SEM),透射电镜(TEM),热重-差热(TGA-DSC)对所制备样品的结构、形貌和NiO含量在复合材料中的含量进行表征。结果表明,热膨胀石墨烯层数约7~8层,层间距约为0.35nm,缺陷多,在水热和微波处理后抗氧化性明显变差。复合材料中氧化镍颗粒平均粒径为25nm,均匀而密集地分散在石墨烯平面上,同时在复合材料中的含量为19.8%。     

Synthesis and performance of electroless Ni–P–TiCN composite coatings on Al substrate

Electroless Ni–P and Ni–P–TiCN composite coatings have been deposited successfully on Al substrates. Scanning electron microscopy (SEM) and energy dispersive X‐ray (EDX) techniques were applied to study the surface morphology and the chemical composition of the deposited films. Moreover, X‐ray diffraction (XRD) proved that Ni–P and Ni–P–TiCN deposits have amorphous structures. The properties of Ni–P–TiCN/Al composite films such as hardness, corrosion resistance and electrocatalytic activity were examined and compared with that of Ni–P/Al film. The results of hardness measurements reveal that the presence of TiCN particles with Ni–P matrix improves its hardness. Additionally, the performance against corrosion was examined using Tafel lines and electrochemical impedance spectroscopy techniques in both of 0.6 M NaCl and a mixture of 0.5 M H₂SO₄ with 2 ppm HF solutions. The results indicate that the incorporation of high dispersed TiCN particles into Ni–P matrix led to a positive shift of the corrosion potential and an increase in the corrosion resistance for all aluminum substrates after their coating with Ni–P–TiCN. In addition, Ni–P–TiCN/Al electrodes showed a higher electrochemical catalytic activity and stability toward methanol oxidation in 0.5 M NaOH solution compared with that of Ni–P/Al. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and characterization of fluorine functionalized graphene oxide dispersed quinoline-based polyimide composites having low-k and UV shielding properties

Polyimide nanocomposites having low-k and UV shielding properties have been developed using fluorine functionalized graphene oxide and bis(quinoline amine) based polyimide. The polyimide was synthesized using bis(quinoline amine) and pyromellitic dianhydride at appropriate experimental conditions, and its molecular structure was confirmed through various spectral analysis such as FTIR and NMR. The polyimide (PI) composites were prepared using bis(quinoline amine), pyromellitic dianhydride, and separately filled with 1, 5, 10 wt% of fluorinated graphene oxide (FGO) through in situ polymerization. The polymer composites were characterized using thermo gravimetric analysis (TGA), X-ray powder diffraction (XRD), and scanning electron microscopy (SEM). In addition, the water contact angle, dielectric behavior, and UV–Vis shielding behavior of FGO/PI composites were evaluated. The value of the water contact angle of the polyimide was increased with increment of FGO in the polyimide matrix. The highest water contact angle of polyimide composites observed 108° was obtained for 15 wt% FGO reinforced polyimide composite. The value of the dielectric constant for neat, 1, 5, and 15 wt% FGO reinforced polyimide composites was obtained as 4.5, 3.7, 2.6, and 2.0, respectively. It is also observed from by UV–Vis spectroscopy analysis that the FGO reinforced polyimide composites have good UV shielding behavior.     

Low percolation conductive graphite flakes-filled poly(urethane-imide) composites with high thermal stability via imidization self-foaming structure

In the study, the conductive graphite flakes filled poly(urethane-imide) composites (PUI/GFs) with high performance were constructed by the thermal imidization self-foaming reaction. It was found that the foaming action could promote the redistribution of GFs during curing process and the formation of stable linear conductive pathways. The percolation threshold of PUI/GFs composites was lowered from 1.26 wt% (2000 mesh GFs) or 0.86 wt% (1000 mesh GFs) to 0.79 wt% (500 mesh GFs), which were relatively low percolation thresholds for polymer/GFs composites so far. When the content of 500 mesh GFs was 4.0 wt%, the electrical conductivity of the composite was as high as 3.96 × 10^?1 S/m. Also, a poly(urethane-imide) (PUI) matrix with excellent thermal stability (T_d10%: 334.97 °C) and mechanical properties (elongation at break: 324.52%, tensile strength: 15.88 MPa) was obtained by introducing the rigid aromatic heterocycle into the polyurethane (PU) hard segments. Moreover, the zero temperature coefficient of resistivity for the composites was observed at the temperature range from 30 °C to 200 °C. Consequently, PUI/GFs composites may provide the novel strategy for considerable conductive materials with high thermal stability in electrical conductivity.