Characterisation of tram noise emission and contribution of the noise sources

The recent expansion of French tram networks and the related local residential complaints mean that a better knowledge of the situations leading to negative reactions from the local inhabitants is required. Hence a research project has been conducted to evaluate and describe noise and vibration emission of trams as well as the perception by the local residents. This paper investigates tram noise emission on common straight track sections, involving two vehicle scales. First the acoustic power and the mean vertical directivity of the total tramset is assessed using an arc of microphones. Then the localisation and the analysis of the main noise sources are performed by means of a cross array during the tram pass-by. Two tram types representing two generations of French rolling stock, both running on two sites with distinct track characteristics, have been investigated considering the effect of speed, tram type, and track type on the noise source contributions and spectral features. Most sources are located in the lower part of the trams, mainly related to rolling noise, with a strong dependence on speed and track type. The tram type dependency, although globally of second importance, influences greatly the noise spectral distribution and behaviour. The HVAC was the only roof-mounted source which could be detected; its contribution towards building storeys becomes significant in configurations of low rolling noise. A tram noise emission model based on the various noise sources has been developed.     

利用“神光-Ⅱ”激光装置多路光束叠加直接驱动下的冲击波平面性及稳定性

利用“神光-Ⅱ”的3路基频光输出及小透镜列阵束匀滑技术,通过优化设计和合理地选择光路组合,实现了多路叠加斜入射的驱动激光, 在靶材料中产生一个650~750μm范围内平面性良好的冲击波,有效地提高了“神光-Ⅱ”输出光束的利用率。同时,利用斜面靶进行的冲击稳定性实验表明,在靶面功率密度分别为3.26×1014及2.56×1014W/cm2时,冲击波至少在28.38~55.82和22.13~35.07μm的Al样品厚度内是稳定传播的。     

Copper-cobalt-nickel oxide nanowire arrays on copper foams as self-standing anode materials for lithium ion batteries

Numerous scientists are in the pursuit of energy storage materials with high energy and high power density by assembly of electrochemically active materials into conductive scaffolds, owing to the emerging need for next-generation energy storage devices. In this architectures, the active materials bonded to the conductive scaffold can provide a robust and free-standing structure, which is crucial to the fabrication of materials with high gravimetric capacity. Thus, hierarchical copper-cobalt-nickel ternary oxide (CuCoNi-oxide) nanowire arrays grown from copper foam were successfully fabricated as free-standing anode materials for lithium ion batteries (LIBs). CuCoNi-oxide nanowire arrays could provide more active sites owing to the hyperbranched structure, leading to a better specific capacity of 1191 mAh/g, cycle performance of 73% retention in comparison to CuO nanowire structure, which exhibited a specific capacity of 1029 mAh/g and capacity retention of 43%, respectively.     

稀疏矢量阵信号栅瓣及对称伪峰干扰抑制

稀疏矢量阵进行宽带信号处理时,强目标的栅瓣及对称伪峰会干扰弱目标的检测,提出了一种基于理论干扰预测的加权抑制方法。方法利用矢量阵波束形成先获得强目标的波达方向(Direction Of Arrival,DOA)信息以及目标所在方位各频率的幅度谱信息,再利用理论计算公式获得强目标的栅瓣和对称伪峰角度上对应的各频率点的幅度谱强度信息,通过在方位、频率维度加权的方式对强目标的栅瓣和伪峰干扰进行抑制,来改善在强干扰下的弱目标检测能力。方法也适用于多目标情况,对各个目标依次使用,减少多目标时栅瓣和对称伪峰对方位历程的影响,净化了时间方位历程图。对所提方法给出了理论推导过程并进行了仿真和实验验证,实验结果验证可行。结果表明,新方法可以有效地抑制强目标的栅瓣和对称伪峰干扰,提高弱目标的检测能力,此外,净化后的时间方位历程图更利于弱目标检测和目标数量的估计。     

存在通道幅相与互耦两种误差的均匀圆环阵流形曲线拟合方法

针对实际装配后均匀圆环阵的阵列流形向量偏离理论值的问题,提出一种利用单声源从不同方位入射阵列时的阵列幅度相位响应拟合阵列流形模型的算法。考虑阵列存在通道幅度相位一致性偏差和阵元间互耦作用,导出阵列幅度相位响应与流形误差参数的关系式,利用互耦矩阵在模态域可与阵列流形分离的特性,将关于误差参数的关系式降次为线性方程组,再联合多个方位对误差参数做最小二乘估计。对于只存在其中一种误差的特例情况,给出了对应高精度、低复杂度的估计方法。最后,利用数值仿真对所提方法的拟合精度进行评估,拟合后的阵列流形误差距离缩减至10^-2量级,水池实验数据也验证了算法在实际应用中的可行性。     

频率不变波束形成器抽头稀疏化设计的交替方向乘子法

针对具有空间响应变化函数约束的频率不变波束形成器设计问题,提出了采用交替方向乘子法实现抽头稀疏设计的优化算法。该算法利用交替方向乘子法能够将原始优化问题进行分裂处理的特点,通过引入替代变量和指示函数,使得表征波束形成器抽头稀疏度量的非凸L₀范数与阵列响应约束分离,进而将问题分裂到元素层级并给出近邻算子的解。对于指示函数的近邻算子求解,在分裂到元素层级后则退化为简单的双边约束问题,因而降低了优化求解的计算复杂度。仿真分析表明,提出的方法比现有的L₁范数方法在宽频带条件下的抽头稀疏度能够提升6%~13%,通带最大波动误差减小了约2 dB,并且优化消耗时间更短。实验结果进一步验证了所提方法在实现高抽头稀疏度波束形成的同时,对声信号造成的失真更小。因此,所提出的方法在降低传声器阵列波束形成器的实现复杂度以及保持阵列响应的频率不变性能方面更具有优势。     

浅海非均匀水平阵宽带声场信号无源孔径扩展

大孔径水平阵对于浅海低频水声物理实验研究和应用至关重要,然而受实际情况制约,通常使用的水平基阵孔径十分有限,通过孔径扩展处理来扩展基阵孔径是一条重要途径。传统的无源孔径扩展方法是建立在均匀线阵、匀速相对运动和相干窄带连续信号的基础上的,难以适用于非均匀阵以及非连续宽带声源的情况。针对这些问题,提出了非均匀阵宽带声场信号的无源孔径扩展方法。使用静止布设在海底的非均匀水平短阵接收运动声源重复发射的宽带声信号,先开展均匀空间插值,然后在阵元域和波束域进行宽带扩展孔径处理。仿真和实验结果表明,在水深约70 m的浅海波导环境中,纵向间隔27.5 m的2个阵元接收20~200 Hz宽带声场,其空间插值结果与真值的相关系数大于0.99,说明宽带声场插值方法的合理性。在水平非均匀、纵向孔径250 m的短阵接收声场无法分析简正波频散特征的情况下,仿真和实验数据经过宽带无源孔径扩展处理得到孔径大于1 km的均匀线阵的声场,能高分辨区分各阶简正波,证明所提方法是有效的。     

圆弧形面阵自适应波束形成快速计算方法

针对圆弧形面阵估计水下目标二维波达方向的问题,提出一种降维处理的自适应波束形成方法。利用圆弧形面阵模型简化阵列内插矩阵的计算,通过垂直和水平两阶段波束加权,降低自适应波束形成维数,从而实现快速估计声源二维波达方向的目的。仿真结果表明,所提改进方法的计算量较传统二维最小方差无失真波束形成方法降低约一个数量级,且在低快拍条件下具有更明显的噪声抑制优势。湖上实验数据处理结果验证,在复杂水声环境下,所提方法具有较好的目标分辨性能。     

Use of Extraction Disks for Trace Enrichment of Various Pesticides from River and Sea Water Samples

Abstract

C-18 Empore extraction disks were used for the isolation and trace enrichment of different groups of pesticides from river water and artificial sea water at concentration levels of 0.2, 5 and 20 μg/l [chlorotriazines, (atrazine and simazine), their dealkylated metabolites, (deethyl- and deisopropylatrazine), organophosphorus (parathion-ethyl), phenylurea (linuron), anilide (propanil), carbamate (aldicarb and carbofuran) and carbamate transformation products (aldicarb sulfoxide, aldicarb sulfone and 3-hydroxy-7-phenol carbofuran]. The extraction disks allowed high flow rates thus 51 samples could be processed within 2h. 30 min.

For most of the pesticides the recoveries, as determined by liquid chromatography with diode array detection (LC-DAD), varied from 74 up to 125% with coefficients of variations (CV) of 5-10%, whereas for the carbamate transformation products the recoveries were in the range of 30-35% having a CV of 17-21%. At spiking level of 0.2 μg/l the dealkylated triazine metabolites and the carbamate transformation products were not detected at all.     

A comparison of measured room acoustics metrics using a spherical microphone array and conventional methods

The traditional microphone configuration used to measure room impulse responses (IRs) according to ISO 3382:2009 is an omnidirectional and figure-8 microphone pair. IRs measurements were taken in a 2500-seat auditorium to determine how the results from a spherical microphone array (an mh acoustics Eigenmike-em32) compare to those from the traditional microphone setup (a Brüel & Kjær Type-4192 omnidirectional microphone and a Sennheiser MKH30 figure-8 microphone). Measurements were obtained at six receiver locations, with three repetitions each in order to first evaluate repeatability. The metrics considered in this study were: reverberation time (T30), early decay time (EDT), clarity index (C80), strength (G), lateral energy fraction (J_LF) and late lateral energy level (L_J). Before calculating these quantities, the IRs were filtered to equalize the frequency response of the microphones and sound source. For the spherical array measurements, the omnidirectional (monopole) and figure-8 (dipole) patterns were extracted using beamforming. In terms of repeatability, the average standard deviation of the three measurements at each receiver location averaged across all metrics, receivers, and octave bands was found to be 0.01 just noticeable differences (JNDs). The analysis comparing the measurements from the two microphone configurations yielded differences which were less than 1 JND for the majority of metrics, with a few exceptions of EDT and C80 slightly above 1 JND. Based on this case study, these results indicate that spherical microphone arrays can be used to obtain valid room IR measurements, which will allow for the development of new metrics utilizing the higher spatial resolution made possible with spherical arrays.