中空纤维催化膜反应器中环戊二烯的选择加氢反应

将聚乙烯吡咯烷酮（ＰＶＰ）负载钯催化剂（ＰＶＰ－Ｐｄ）镶嵌到三种醋酸纤维（ＣＡ）中空膜（ＣＡ－Ｉ，ＣＡ－Ⅱ，ＣＡ－Ⅲ）内制各中空纤维催化膜，并进一步制成催化膜反应器，在４０℃和０．１ＭＰａ的反应条件下，在催化膜反应器中进行了环戊二烯的选择加氢反应，考察了具有不同氢气渗透率的醋酸纤维丝组成的三种膜反应器对反应的转化率及选择性的影响，并在此基础上考察了各种反应参数对反应的影响，ＣＡ中空纤维催化膜对环戊     

Moisture effects on the glass transition and the low temperature relaxations in semiaromatic polyamides

The influence of moisture absorption on the primary (glass) transition (T_a or T_g) and the low temperature relaxations of semiaromatic amorphous polyamides synthesized by isomeric aliphatic diamine and metha or para oriented phthalicdiacids has been investigated by means of differential scanning calorimeter (DSC) and dynamic mechanical thermal analyser (DMTA). The glass transition of semiaromatic polyamides was lowered due to the water absorption, and the β and the γ relaxations were as well. From the observed T_g and the difference in the heat capacity, the calculated T_g depression per 1 wt % water content was 12.3 K and the result was in good agreement with the experimental data. The depression of the glass transition may be expressed by the same manner as the plasticization of nylon 6 by water. The depressed β relaxation observed in the specimen containing a few percent of moisture was splitted into two transitions due to the reduction of water content, of which one was the elevation of the T_β and another was the simultaneous appearance of the T_γ, and then the single T_γ solely was observed for the completely dried specimen. The T_γ seemed to be merged into or not to be observed by the large and broad T_β transition when the sample was governed by a few percent of water, then it was emerged from the T_β due to water desorption. Thus, the T_β is believed to arise from the intermolecular hydrogen bonding between water molecules or between water and amide groups in wet polyamides. In addition, the γ relaxation originated from the peptide groups is attributable to the inter- and intramolecular hydrogen bonding between amide groups. © 1997 John Wiley & Sons, Inc. J Polyn Sci B: Polym Phys 35: 807–815, 1997     

Gas transport properties of soluble poly(phenylene sulfone imide)s

Gas transport of helium, hydrogen, carbon dioxide, oxygen, argon, nitrogen, and methane in three soluble poly(phenylene sulfone imide)s based on 2,2-bis(3,4-decarboxyphenyl) hexafluoropropane dianhydride (6FDA) has been investigated. The effects of increasing length of well-defined oligo(phenylene sulfone) units on the gas permeabilities and diffusivities were determined and correlated with chain packing of the polymers. Activation energies of diffusion and permeation were calculated from temperature-dependent time-lag measurements. The influences of the central group in the diamine moiety of 6FDA-based polyimides on physical and gas transport properties are discussed. The incorporation of a long oligo(phenylene sulfone) segment in the polymer backbone decreases gas permeability and permselectivity simultaneously. The decreases in permeability coefficients can be mainly related to decreases in diffusion coefficients. Changing the central group of diamine moiety from  S to  SO₂ leads to a 45–50% decrease in CO₂ and O₂ permeabilities without appreciable increase in the selectivities. This is considered to be due to the formation of charge transfer complexes. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1855–1868, 1997     

Synthesis and characteristics of the poly(carboxybetaine)s and the corresponding cationic polymers

Two types of carboxybetaines and their corresponding cationic monomers and polymers are synthesized in this study. Comparing the chemical shifts of the methylene groups in the cationic monomers and carboxybetaines in both ¹H- and ¹³C-NMR spectra reveal that the respective methylene groups are clearly distinguished from their chemical shifts in ¹H- and ¹³C-NMR spectra. The solubilities, moisture regain properties, and solution properties of the poly(carboxybetaine)s and cationic polymers are investigated in relation to their molecular structures. Because the cationic polymers were ionized in an aqueous solution, the cationic polymers were more soluble than the poly(carboxybetaine). For the various functional groups of poly(carboxybetaine)s and cationic polymers, the order of tendency for moisture regain is  COO >  CONH . Results obtained from the reduced viscosity for cationic poly(TMMPAMS) are reversed from that for zwitterionic poly(DMAEAPL). © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3527–3536, 1997     

About the Dominance of Mesopores in Physisorption in Amorphous Materials

Amorphous, porous materials represent by far the largest proportion of natural and men-made materials. Their pore networks consists of a wide range of pore sizes, including meso- and macropores. Within such a pore network, material moisture plays a crucial role in almost all transport processes. In the hygroscopic range, the pores are partially saturated and liquid water is only located at the pore fringe due to physisorption. Therefore, material parameters such as porosity or median pore diameter are inadequate to predict material moisture and moisture transport. To quantify the spatial distribution of material moisture, Hillerborg’s adsorption theory is used to predict the water layer thickness for different pore geometries. This is done for all pore sizes, including those in the lower nanometre range. Based on this approach, it is shown that the material moisture is almost completely located in mesopores, although the pore network is highly dominated by macropores. Thus, mesopores are mainly responsible for the moisture storage capacity, while macropores determine the moisture transport capacity, of an amorphous material. Finally, an electrical analogical circuit is used as a model to predict the diffusion coefficient based on the pore-size distribution, including physisorption.     

凝胶型苯乙烯系离子交换树脂的强度及抗渗透性的影响因素研究 (I)

本文就单体组成中不同引发剂，链转移剂，环二烯，烯丙基类化合物和氧气等对凝胶型苯乙烯系阳离子交换树脂的强度和抗渗透性的影响进行了系统研究。结果显示，采用0．30％的过氧化2－乙基己酸叔丁酯（OT）和0．01％的过氧化苯甲酸特丁酯（CP）代替过氧化二苯甲酰（BPO作引发剂，或者加入0．02％的链转移剂十二烷基硫醇，均能够在一定程度上改善共聚物珠粒的结构均匀性，提高其合成的离子交换树脂的磨后圆球率和抗渗透性能。     

Pulsed field gradient NMR on polybutylcyanoacrylate nanocapsules

The applicability of pulsed field gradient nuclear magnetic resonance spectroscopy to nanocapsule systems is demonstrated on dispersed poly-n-butylcyanoacrylate nanocapsules as a model system. Spectroscopic data are presented that allow for the structural characterization of the inner cavities, the observation of Brownian motion of the capsules and the detection of rapid molecular exchange through the capsule walls. An analytical formula is proposed that yields equilibrium populations and average residence times of a given tracer molecule, thus leading to crucial information regarding the permeability of the capsule walls. Based on these analytical methods, two varieties of nanocapsules are compared that derive from two different preparation procedures. It is found that thinner capsule walls obtained under acidic conditions of the organic phase during interfacial polymerization lead to correspondingly higher exchange rates of benzene as a tracer molecule.     

Synthesis and properties of a poly(diphenylacetylene) containing carbazolyl groups

1-(p-N-Carbazolylphenyl)-2-phenylacetylene (p-CzDPA) was polymerized by TaCl₅–co-catalyst systems (cocatalysts: n-Bu₁Sn, Et₃SiH, and 9BBN) to produce acetone-insoluble polymers in about 60-70% yields. Poly(p-CzDPA) was a yellowish-orange solid, most part of which was soluble in toluene, chloroform, etc., and its weight-average molecular weights were around 4×10⁵. This polymer formed a tough film by solution casting, and was thermally very stable (the onset temperature of weight loss in TGA in air 470°C). The oxygen per-meability coefficient of the polymer at 25°C was lower than two barrers. The present polymer showed photoconductivity and redox activity. © 1995 John Wiley & Sons, Inc.     

Effects of Permeation of Helium through the Walls of Fused Silica Capillary GC Columns

Hold-up times and peak widths have been measured in long fused silica GC capillary columns at high temperature with helium as the carrier gas. The results lead to the conclusion that the helium permeates through the column walls. The conventional Poiseuille theory of carrier gas flow has been extended to include this phenomenon. The resulting “loss modified Poiseuille” model, which uses literature values for the permeability of fused silica to helium, has been used to simulate the observed behavior. Good agreement between simulation and experiment validates the model. Simulations have been used to explore the effect of column permeability on hold-up times, peak widths, and velocity profiles over a broad range of column geometries.     

Laboratory Studies of Depressurization with a High Concentration of Surfactant in Low-Permeability Reservoirs

To solve the problem of high pressure of water injection in low permeability reservoirs, a high concentration of surfactant system was developed in this article. With the solubilization of oil in aqueous surfactant solution as a criterion, a formula was screened from anionic and nonionic-anionic surfactants, and the optimal depressurized system was obtained as follows, 13.3% surfactant HEX +2.23% n-propanol +4.47% n-butanol, the solubilization capability being up to 0.66 g/g. This system had good salt tolerance, and it exhibited water external microemulsion in the range of of 1 to 200 g/L NaCl. Core flooding results show that this high concentration of surfactant system formed water external microemulsion with the residual oil in the core, reducing the displacement pressure over 35%. Meanwhile, the effects of concentration and injection volume on depressurization were also investigated. It is indicated that a good depressurization effect was achieved after injecting 1 pore volume of the system with the salt concentration of 100 g/L.