PLLA microspheres were aminolyzed in hexanediamine/propanol solution to introduce free amino groups on their surface, which were further transferred into aldehyde groups by a treatment of glutaraldehyde. Chitosan‐graft‐lactose was then covalently coupled via Schiff base formation. Morphological variation and chitosan‐graft‐lactose immobilization were characterized. In vitro culture of rabbit auricular chondrocytes demonstrated that the PLLA microcarriers could effectively support the cell attachment and particularly induce cell aggregation on their surface. The formed cell aggregates/microcarriers composite showed higher viability and extracellular matrix production. Thus, the PLLA microcarriers can be potentially used as an injectable delivery system for cartilage repair.
Radially oriented Nd-Fe-B rings are prepared by backward extrusion of fine grained melt-spun powder. Melt-spun powder with the nominal composition of Nd30.5Febal.Co6.0Ga0.6Al0.2B0.9 (wt%) is used as starting material. The effects of process variables, such as deformation temperature (Td), strain rate (ε) and height reduction (Δh%), on the magnetic properties of the rings are investigated. A scanning electron microscope (SEM) equipped with an energy spectrum device is used to study the metallograph and microfracture of the extruded rings. The Br and (BH)max reach the optimum values at Td=800℃, ε =0.01 mm/s, and Δh% =70%. It is found by SEM observations that the particle boundaries, which seemingly correspond to the interfaces of the starting melt-spun powders, emerge after the corrosion of metallography specimens. This is helpful for studying the effects of powder-powder interface on the local deformation and deformation homogeneity in the rings. For different spatial positions of the extruded rings, there are characteristic metallographies and microfractures. The upper end of the rings has the least deformation and worst texture, and therefore the worst magnetic properties. The magnetic properties in the radial direction increase slightly along the axis from the bottom to the middle, then steeply decrease at the upper end of the ring. The deformation and the formation-of-texturing processes are discussed. The deformation and the texturing formation of melt-spun Nd-Fe-B alloys probably involve grain boundary sliding and grain rotation, the solution-precipitation process and preferential growth of Nd2Fe14B nanograins along the easy growth a-axis. 相似文献
Using a radio-frequency reactive magnetron sputtering technique, a series of the single-phased Ag20 films are deposited in a mixture of oxygen and argon gas with a flow ratio of 2:3 by changing substrate temperature (Ts). Effects of the Ts on the microstructure and optical properties of the films are investigated by using X-ray diffractometry, scanning electron microscopy and spectrophotometry. The single-phased Ag20 films deposited at values of Ts below 200℃ are (111) preferentially oriented, which may be due to the smallest free energy of the (111) crystalline face. The film crystallization becomes poor as the value of Ts increases from 100℃ to 225℃. In particular, the Ag20 film deposited at Ts=225℃ loses the (111) preferential orientation. Correspondingly, the film surface morphology obviously evolves from a uniform and compact surface structure to a loose and gullied surface structure. With the increase of Ts value, the transmissivity and the reflectivity of the films in the transparent region are gradually reduced, while the absorptivity gradually increases, which may be attributed to an evolution of the crystalline structure and the surface morphology of the films. 相似文献
Highly textured Ni nanowire arrays were fabricated into anodic aluminum oxide(AAO) templates by pulse DC electrodeposition.The applied voltage and pH value of electrolytes were found strongly affecting the microstructure and magnetic properties of Ni nanowire arrays.Low applied potential and pH value both prefer to form polycrystalline fcc Ni nanowires.Increasing the applied potential or pH value favors the Ni [220] texture and even eventually forms the [220] oriented single crystal Ni wires,while exorbitan... 相似文献
Microstructures are usually fabricated on the surface of optical sheets to improve the optical characteristics. In this study, a new fabrication process with UV (ultraviolet) laser direct writing method is developed to embed microstructures inside the glass. Then the optical properties of glass such as reflection and refraction indexes can be modified. Single- and multi-layer microstructures are designed and embedded inside glass substrate to modify the optical characteristics. Both luminance and uniformity can be controlled with the embedded microstructures. Thus, the glass with inside pattern can be used as a light guide plate to increase optical performance. First, an optical commercial software, FRED, is applied to design the microstructure configuration. Then, UV laser direct writing with output power 2.5-2.6 W, repetition rate 30 kHz, wave length: 355 nm, and pulse duration 15 ns is used to fabricate the microstructures inside the glass. The effect of dot pattern in the glass such as the dot pitch, the layer gap, and the number of layer on the optical performance is discussed. Machining capacity of UV laser ranges from micron to submicrometer; hence with this ultrafast laser pulse, objectives of various dimensions such as dot, line width, and layers can be easily embedded in the glass by one simple process. In addition, the embedded microstructures can be made with less contamination. Finally, the optical performance of the glasses with various configurations is measured using a Spectra Colorometer (Photo Research PR650) and compared with the simulated results. 相似文献