Deformation and annealing behaviour of a low carbon high Mn TWIP steel microalloyed with Ti

ABSTRACT

A low carbon high Mn, Ti microalloyed dual phase TWIP steel has been processed through cold rolling and annealing. X-ray diffraction reveals the maximum austenite (≈92%) in HRACST sample whereas, the 50CD sample shows 29% ferrite. The microstructure of HRAC and HRACST samples reveal austenite grains with annealing twins and deformation induced ferrite (DIF). The higher amount of DIF along with deformation twins form during cold deformation. Annealing at 500°C shows recovery, whereas at 700°C shows partial recrystallisation and at 900°C reveals almost full recrystallisation. TEM microstructures of the 900°C for 30?min samples reveal annealing twins with TiC particle. Strong Brass {110}<112> and Goss{110}<001> texture components are observed in HRAC, HRACST and 50CD samples. Goss Twin (GT) {113}<332> and Copper Twin (Cu-T) {552}<115> components are observed in 50CD sample. Addition of Ti results in an average grain size of 20?μm. Maximum YS (1176?MPa) and UTS (1283?MPa) values with the lowest ductility of 11% have been obtained for the 50CD sample which is related to the formation of extensive deformation twin and a higher fraction of DIF. 700°C-30?min and 700°C-60?min samples show an increase in ductility (23% and 34%, respectively) with a marginal decrease in tensile strength (1054?MPa). Annealing at 900°C shows ductility restoration up to 60% with higher tensile strength compared to HRACST sample. Ductile fracture of HRAC and HRACST samples transform to brittle fracture in the 50CD sample. Annealing at 900°C for 30?min shows ductile fracture with some (Fe, Mn)S and TiC particles.     

(n,n)-(2n, 0)碳纳米管异质结的扭转力学特性

相近直径的锯齿型和扶手椅型碳纳米管可以共轴组合形成5-7碳环交替出现的柱形对称异质结. 本文利用分子动力学方法研究了直径相近且等长锯齿型和扶手椅型碳纳米管形成的(n, n)-(2n, 0)结在扭转过程中的扭矩和轴向应力随扭转角度的变化规律以及应力传递过程. 研究发现, (n, n)-(2n, 0)结扭转应变在达弹性限度内不会产生轴向应力, 该效应对基于碳纳米管扭转特性的纳米振荡器件的设计具有重要意义.     

热处理对CH薄膜表面粗糙度及力学性能的影响

利用低压等离子体化学气相沉积法制备厚度约为7 m的辉光放电聚合物薄膜,将制备的薄膜样品放入通有氩气保护的热处理炉中加热至300 ℃,分别进行6,10,24 h的保温热处理。通过白光干涉仪观察分析了不同保温时间下辉光放电聚合物薄膜的表面粗糙度; 利用傅里叶变换红外吸收光谱分析了300 ℃条件下不同保温时间对薄膜结构的影响; 采用纳米压痕仪表征了不同保温时间热处理后,薄膜硬度及模量的变化。结果表明:随着保温时间的增加,薄膜的表面均方根粗糙度由12 nm降至4.43 nm。薄膜结构中甲基的相对含量减少,双键的相对含量增加,碳链变长,同时薄膜网络结构的交联化程度增强。硬度和模量随着保温时间的增加先减小后增大。     

Preparation,Morphology and Properties of Poly(Trimethylene Terephthalate)/Thermoplastic Polyester Elastomer Blends

Poly(trimethylene terephthalate)(PTT)/thermoplastic polyester elastomer (TPEE) blends were prepared and their miscibility, crystallization and melting behaviors, phase morphology, dynamic mechanical behavior, rheology behavior, spherulites morphology, and mechanical properties were investigated by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), parallel-plate rotational rheometry, polarized optical microscopy (POM), wide angle X-ray diffraction (WAXD), universal tensile tester and impact tester, respectively. The results suggested that PTT and TPEE were partially miscible in the amorphous state, the TPEE rich phase was dispersed uniformly in the solid matrix with a size smaller than 2 μm, and the glass transition temperatures of the blends decreased with increasing TPEE content. The TPEE component had a good effect on toughening the PTT without depressing the tensile strength. The blends had improved melt viscosities for processing. When the blends crystallized from the melt state, the onset crystallization temperature decreased, but they had a faster crystallization rate at low temperatures. All the blends’ melts exhibited a predominantly viscous behavior rather than an elastic behavior, but the melt elasticity increased with increasing TPEE content. When the blends crystallized from the melt, the PTT component could form spherulites but their morphology was imperfect with a small size. The blends had larger storage moduli at low temperatures than that of pure PTT.     

ε-CL-20/F_(2311) PBXs力学性能和结合能的分子动力学模拟

本文应用分子动力学(MD)模拟方法,研究高能量密度化合物六硝基六氮杂异伍兹烷(ε-CL-20)与常用高聚物粘结剂F2311所构成的CL-20/F2311高聚物粘结炸药(PBXs)的力学性能和结合能随温度和高聚物浓度而变化的规律.结果表明,添加高聚物于主体炸药中,使其弹性模量减小,表明刚性减小,弹性增大,机械力学性能大为改善;在一定范围内,随高聚物F2311在PBXs中浓度的增加,体系结合能从正值变为负值,而随温度升高,体系的结合能变化不是很明显.     

Broadband energy harvesting via magnetic coupling between two movable magnets

Harvesting energy from ambient mechanical vibrations by the piezoelectric effect has been proposed for powering microelectromechanical systems and replacing batteries that have a finite life span. A conventional piezoelectric energy harvester （PEH） is usually designed as a linear resonator, and suffers from a narrow operating bandwidth. To achieve broadband energy harvesting, in this paper we introduce a concept and describe the realization of a novel nonlinear PEH. The proposed PEH consists of a primary piezoelectric cantilever beam coupled to an auxiliary piezoelectric cantilever beam through two movable magnets. For predicting the nonlinear response from the proposed PEH, lumped parameter models are established for the two beams. Both simulation and experiment reveal that for the primary beam, the introduction of magnetic coupling can expand the operating bandwidth as well as improve the output voltage. For the auxiliary beam, the magnitude of the output voltage is slightly reduced, but additional output is observed at off-resonance frequencies. Therefore, broadband energy harvesting can be obtained from both the primary beam and the auxiliary beam.     

基于多物理场的TFC磁头热传导机理及其影响因素仿真研究

为了利用微尺度热效应的热致飞高控制(TFC)磁头技术实现磁头飞行高度的精确控制,分析了工作状态下TFC滑块在多物理场综合作用下所呈现出来的传热特性及其主要影响因素,考虑了磁头磁盘间超薄气膜的稀薄效应,建立滑块导热、空气轴承表面传热、气膜流动等模型,利用有限元法,对磁头热变形作用机理及热传导特性对滑块动力学特性影响进行了仿真研究,结果表明,建立的传热模型及对雷诺方程的修正适用于求解磁头磁盘界面气膜传热问题和磁头滑块的动力学问题;影响滑块热力学性能的因素主要可以归结为加热器高度、热生成率以及材料的传热系数;空气轴承力及工作表面热变形的双重作用决定了滑块飞行高度的改变.仿真结果为磁头滑块加热器的设计及空气轴承动力学特性分析提供了依据.     

完整有势力学系统的高阶Lagrange方程

首先提出力学系统高阶速度能定理,阐明了系统高阶速度能量的物理意义;然后提出力学系统有势的一般判据.在此基础上,引入高阶Lagrange函数,得出完整有势力学系统的高阶Lagrange方程,并得到系统高阶循环积分和高阶广义能量积分. 关键词： 高阶速度能定理 有势力学系统 高阶Lagrange方程 高阶Lagrange函数     

完整系统Appell方程的Lie-Mei对称性与守恒量

研究了完整系统Appell方程的Lie-Mei对称性与守恒量.在完整系统Appell方程的基础上,给出了Appell方程的Lie-Mei对称性的定义和判据,得到了Appell方程的Lie-Mei对称性导致的Hojman守恒量和Mei守恒量.举例说明结果的应用.     

光学微盘腔与三能级量子点系统中的模耦合研究

用一种全量子理论方法研究了波导、光学微盘腔与三能级量子点耦合系统的动力学过程,求出其耦合后的透射模和反射模的解析解. 由于微腔表面粗糙引起反向散射,在微腔内形成两简并回音壁耦合共振模,其耦合率为β;量子点的两激发态分别以耦合率g₁,g₂与回音壁耦合共振模产生耦合. 在实数空间里,得出透射光谱和反射光谱的数值解,这些三能级模型结果比二能级模型结果更接近真实光学微盘腔系统,能更好地显示耦合系统的动力学特性. 关键词： 模耦合 光学微盘腔 三能级量子点 全量子理论