固相反应制备无氯CuY催化剂及其催化氧化羰基化—固相反应温度和铜负载量的影响

以乙酰丙酮铜Cu(acac)₂为铜源、 NH₄Y分子筛为载体, 采用固相反应制备了无氯CuY催化剂, 考察了在甲醇氧化羰基化合成碳酸二甲酯过程中固相反应温度和Cu负载量对CuY催化剂催化性能的影响, 分析了CuY催化剂物相结构、 可还原性Cu物种和织构性质对催化性能的影响. 结果表明, 随着固相反应温度的升高, 与NH₄Y中N\begin{array}{c}{H}_4^{+}\end{array}发生离子交换的Cu²⁺交换度和活性中心Cu⁺含量先增大后降低, CuY催化剂活性也呈现出相同的变化趋势; 负载量(质量分数)低于10%时, 受分子筛残留B酸位影响, 碳酸二甲酯的选择性较低, 而负载量高于12%时, CuY催化剂中出现了CuO物种, 且粒子逐渐长大, 覆盖部分活性中心, 甚至堵塞孔道, 使催化剂活性降低. 当固相反应温度为250 ℃, Cu负载量为12%时, 活性中心Cu⁺含量最高, 催化剂表现出最佳的催化活性, 碳酸二甲酯基于甲醇的时空收率为267.3 mg·g^-1·h^-1, 甲醇转化率为6.9%, 碳酸二甲酯(DMC)的选择性为69.2%.     

分子动力学模拟冲击波加载下CL-20/BTF共晶的分解

本文采用Reax FF-lg分子反应性力场研究了六硝基六氮杂异伍兹烷(CL-20)和苯并三氧化呋咱(BTF)形成的共晶在冲击波加载下的反应情况。结果发现:冲击波速度为Us=9 km·s-1时,含能分子快速分解。冲击加载在不同方向上时,分解速率不同,冲击波沿X轴方向时分解最快。反应早期主要是N-NO2键的断裂,生成NO2。较大分子质量的团簇会出现在反应前期,随着反应的进行团簇数量增加。整个模拟过程中,主要产物N2的数目有较大波动,28 ps达最大值。冲击波速度对反应后期的影响较小。     

Ceramic Filter Balls Loaded with α-Fe2O3 and Their Application to NH3-N Wastewater Treatment

Hydrolysis reaction of Fe(NO₃)₃ at a high temperature in the presence of urea as the homogeneous precipitant was studied. With the prepared ceramic filter balls loaded with α-Fe₂O₃ after high temperature calcination, the loading of α-Fe₂O₃ on the porous ceramic filter balls from Fe(NO₃)₃ solutions of different concentrations and mechanical stability of the loaded α-Fe₂O₃ were studied. The product was characterized using XRD and SEM. Adsorption experiments were conducted to evaluate the performance of the product in adsorbing NH₃-N. It turned out that the specific surface area of the ceramic filter balls loaded with α-Fe₂O₃ had increased to 36.5387 m²/g from original 4.6127 m²/g. When the concentration of Fe(NO₃)₃ was 0.40 mol/L, the loading of α-Fe₂O₃ on the ceramic filter balls accounted for 8.4% of the total mass of the adsorbent and α-Fe₂O₃ was adsorbed on the filter balls very well. The adsorption isotherm of NH₃-N on the ceramic filter ball adsorbent loaded with α-Fe₂O₃ was of Langmuir type. The saturated adsorption capacity was 3.33 mg/L, and the adsorption constant K was 0.1873. NH₃-N was adsorbed by α-Fe₂O₃ more easily, which was a kind of specific adsorption.     

Proton and methanol transport behavior of SPEEK/TPA/MCM-41 composite membranes for fuel cell application

This paper reports proton and methanol transport behavior of composite membranes prepared for use in the direct methanol fuel cell (DMFC). The composite membranes were prepared by embedding various proportions (10–30 wt.%) of inorganic proton conducting material (tungstophosphoric acid (TPA)/MCM-41) into sulfonated poly(ether ether ketone) (SPEEK) polymer matrix. The results indicate that the proton conductivity of the membranes increases with increasing loading of solid proton conducting material. The highest conductivity value of 2.75 mS/cm was obtained for the SPEEK composite membrane containing 30 wt.% solid proton conducting material (50 wt.% TPA in MCM-41). The methanol permeability and crossover flux were also found to increase with increasing loading of the solid proton conducting material. Lowest permeability value of 5.7 × 10⁻⁹ cm² s⁻¹ was obtained for composite membrane with 10 wt.% of the solid proton conducting material (40 wt.% TPA in MCM-41). However, all the composite membranes showed higher selectivity (ratio between the proton conductivity and the methanol permeability) compared to the pure SPEEK membrane. In addition, the membranes are thermally stable up to 160 °C. Thus, these membranes have potential to be considered for use in direct methanol fuel cell.     

连续碳纤维增强的聚芳醚酮在Ⅰ型循环载荷下的层间破坏

用双悬臂梁(DCB)试件研究了连续碳纤维增强的聚芳醚酮复合材料(CF/PEK-C),在Ⅰ型循环载荷作用下的层间裂纹扩展行为.循环载荷采用载荷控制模式,最小载荷与最大载荷之比为0.5.在疲劳试验中,仍然发现有“阻力曲线”现象存在.层间裂纹扩展速率用指数定律与相应的应变能释放速率联系起来,并对结果进行了讨论.     

Effect of cyclic loading on tensile properties of PC and PC/ABS

The effects of cyclic loading on tensile fracture properties of polycarbonate (PC) and the alloy of polycarbonate and acrylonitrile-butadiene-styrene (PC/ABS) are experimentally investigated in the paper. Two digital cameras are used to record simultaneously the tensile deformation of specimens and the large deformation and the necking process of these polymers are discussed. Two lateral contractions are not identical at the later tensile stages and the contraction ratios in each lateral direction are related with the tensile strains in axial direction on width and thickness surface. The curvature radiuses at the minimum section during necking process are shown. The volume increases during necking process and then decreases gradually. The yield stress and fracture stress of PC/ABS are lower than that of PC. The degradation of the fracture stress and fracture strain due to the application of cyclic loading is larger for PC than that for PC/ABS, and these can be used to explain qualitatively why PC has higher fatigue crack growth rate than PC/ABS.     

In vitro degradation of porous poly(l-lactide-co-glycolide)/β-tricalcium phosphate (PLGA/β-TCP) scaffolds under dynamic and static conditions

In vitro degradation of porous poly(l-lactide-co-glycolide)/β-tricalcium phosphate (PLGA/β-TCP) scaffolds was studied by incubating the samples in phosphate buffered saline (PBS) at 37 °C and pH 7.4 under dynamic loading with respect to static conditions for 12 weeks. Under dynamic conditions, acidity of PBS was alleviated by the better solution circulation, and water absorption of the scaffolds increased more than that under static conditions in the first 8 weeks. Changes in mass, height, diameter, relative molecular mass and its distribution also happened more remarkably under dynamic conditions. Moreover, obvious cracks and a larger amount of β-TCP particles were observed on the wall of the scaffolds after degradation for 12 weeks under dynamic loading. Compressive modulus and strength showed an increase from the beginning to the 10th week but were lower after then. Results showed that degradation of PLGA/β-TCP scaffolds under dynamic conditions exhibited a significantly faster rate than that under static conditions.     

Synthesis and Investigation of Soluble Polymer-supported Dendrimers

Poly（ethylene glycol） （PEG）-supported dendrimers have been synthesized using 2.4,6-trichloro-1,3,5-triazine （TCT） as dendrons and tris（hydroxymethyl）aminomethane as tinkers with high loading capacity, excellent solubility and thermal stability by divergent method. The new synthesized PEG-supported G2.0 dendrimer has 10 times as large functional group loading capacity as commercial PEG3400 with overall yield 44.0%.     

有序介孔碳CMK-3微波负载NiO及其电容性能研究

微波法负载具有简便、快速、均匀的优点. 本文尝试以乙二醇为还原剂, Ni(Ac)₂为Ni源, 通过微波辐射负载及低温空气煅烧在CMK-3上形成NiO. 对样品进行X射线衍射(XRD)、透射电子显微镜(TEM)、N₂吸脱附等结构表征及循环伏安(CV)等电化学性能测试. 结果显示, 微波法并经低温空气煅烧后有序介孔碳CMK-3的小角XRD峰强度变弱、比表面积下降、孔容减小, 但却使其比电容从229.3 F/g提高到295.9 F/g, 大于文献报导中介孔碳负载MnO₂, RuO₂•xH₂O后的比电容值. 由此说明微波法是有效的负载方法, 具有较好的应用前景.     

V2O5负载量对V2O5/Al2O3氧化活化正庚烷催化裂解反应的影响

采用X射线衍射, 低温氮气吸脱附, 氨气程序升温脱附和吡啶吸附红外光谱分析方法对不同活性组分负载量V2O5/Al2O3的性质进行了表征. 根据表面VOx单元密度, 推测V2O5负载量为20%-25% (w)对应着V2O5/Al2O3表面达单层覆盖状态; V2O5的负载使Al2O3表面Lewis酸量减少, 并出现Br?nsted酸, 对应着氧化态VOx单元中的V―OH; 随着负载量的增加, Brφnsted酸量增加至负载量为20%时达到最大值. 对V2O5/Al2O3中活性组分负载量对其氧化活化正庚烷催化裂解反应的影响进行了考察. 结果表明, 在V2O5负载量为20%-25%时,V2O5/Al2O3的引入对正庚烷在HZSM-5平衡剂上催化裂解反应的促进作用最明显, 此时VOx单元在V2O5/Al2O3表面形成单层覆盖状态, 可提供最大量的表面晶格氧, 因而对正庚烷具有最强的氧化活化作用; V2O5负载量继续增加形成体相的V2O5和AlVO4, 不利于晶格氧参与正庚烷的转化, 因而反应性能有所下降.