水斗非定常自由水膜流三维贴体数值模拟

本研究采用水斗三维非正交贴体坐标系进行了非定常自由水膜流动的数值解析。对不规则水斗内表面采用三维非正交贴体坐标系下离散点进行拟合,推导了曲面离散点的法向矢量和曲面微元面高斯曲率、平均曲率等几何特征量的计算公式,进而导出流体粒子在运动方向上曲率计算式。在水斗三维贴体坐标系中,还推导了流体粒子在水斗曲面上的运动控制方程。最后对某水轮机水斗内表面非定常自由水膜流进行了数值模拟,得到其非定常水膜流态分布。     

AGE method simulations of a turbulent far‐wake compared to spectral DNS

Turbulent flow simulation methods based on finite differences are attractive for their simplicity, flexibility and efficiency, but not always for accuracy or stability. This paper demonstrates that a good compromise is possible with the advected grid explicit (AGE) method. Starting from the same initial field as a previous spectral DNS, AGE method simulations of a planar turbulent wake were carried out as DNS, and then at three levels of reduced resolution. The latter cases were in a sense large‐eddy simulations (LES), although no specific sub‐grid‐scale model was used. Results for the two DNS methods, including variances and power spectra, were very similar, but the AGE simulation required much less computational effort. Small‐scale information was lost in the reduced resolution runs, but large‐scale mean and instantaneous properties were reproduced quite well, with further large reductions in computational effort. Quality of results becomes more sensitive to the value chosen for one of the AGE method parameters as resolution is reduced, from which it is inferred that the numerical stability procedure controlled by the parameter is acting in part as a sub‐grid‐scale model. Copyright © 2002 John Wiley & Sons, Ltd.     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

曲轴箱窜气量检测仪的研制

介绍了车用压差式气体流量传感器的结构设计和电测电路，指出了传感器的使用范围，由实验测出了特性曲线．该仪器可检测车用发动机曲轴箱窜气量，适用于发动机不解体故障诊断．     

前缘弯掠斜流转子叶顶间隙流动特性数值分析

本文对前缘弯掠斜流转子叶顶间隙内的流动特性进行了数值分析。结果表明:叶顶间隙气流与主流发生卷吸而生成泄漏涡。泄漏涡作用的区域具有较低的压力分布。在叶片通道内,泄漏涡沿着与转子旋向相反的方向朝相邻叶片的压力面移动。大间隙时的泄漏涡比小间隙时强烈。低流量时泄漏涡的作用区域比高流量时大。在各种流量特性下,叶顶尾缘近吸力面区域都存在着二次间隙流。     

Numerical analysis of turbulent structure in compound meandering open channel by algebraic Reynolds stress model

The turbulent flow in a compound meandering channel with a rectangular cross section is one of the most complicated turbulent flows, because the flow behaviour is influenced by several kinds of forces, including centrifugal forces, pressure‐driven forces and shear stresses generated by momentum transfer between the main channel and the flood plain. Numerical analysis has been performed for the fully developed turbulent flow in a compound meandering open‐channel flow using an algebraic Reynolds stress model. The boundary‐fitted coordinate system is introduced as a method for coordinate transformation in order to set the boundary conditions along the complicated shape of the meandering open channel. The turbulence model consists of transport equations for turbulent energy and dissipation, in conjunction with an algebraic stress model based on the Reynolds stress transport equations. With reference to the pressure–strain term, we have made use of a modified pressure–strain term. The boundary condition of the fluctuating vertical velocity is set to zero not only for the free surface, but also for computational grid points next to the free surface, because experimental results have shown that the fluctuating vertical velocity approaches zero near the free surface. In order to examine the validity of the present numerical method and the turbulent model, the calculated results are compared with experimental data measured by laser Doppler anemometer. In addition, the compound meandering open channel is clarified somewhat based on the calculated results. As a result of the analysis, the present algebraic Reynolds stress model is shown to be able to reasonably predict the turbulent flow in a compound meandering open channel. Copyright © 2005 John Wiley & Sons, Ltd.     

可压稠密气固两相流动过程的模拟计算

基于稠密气体分子运动论和颗粒动理学,建立可压稠密气固两相流动模型。采用梯度模拟来考虑气相可压缩性对气相湍流的影响。模拟计算表明气固两相射流速度沿轴向和径向减小,颗粒浓度下降。气固两相射流具有高的颗粒温度,呈现强烈的气固两相湍流流动特性。     

Stable Ergodicity and Frame Flows

In this note we show that all diffeomorphisms close enough to the time-one map of the frame flow on certain negatively curved manifolds are ergodic. As a simple corollary we deduce that the frame flows are ergodic for all compact manifolds with curvature pinched sufficiently close to –1, thus providing results in the case of manifolds of dimension 7 or 8 which were missing from the results of Brin and Karcher.     

Rhythmic growth of ring‐banded spherulites in blends of liquid crystalline methoxy‐poly(aryl ether ketone) and poly(aryl ether ether ketone)

Rhythmic growth of ring‐banded spherulites in blends of liquid crystalline methoxy‐poly(aryl ether ketone) (M‐PAEK) and poly(aryl ether ether ketone) (PEEK) has been investigated by means of differential scanning calorimetry (DSC), polarized light microscopy (PLM), and scanning electron microscopy (SEM) techniques. The measurements reveal that the formation of the rhythmically grown ring‐banded spherulites in the M‐PAEK/PEEK blends is strongly dependent on the blend composition. In the M‐PAEK‐rich blends, upon cooling, an unusual ring‐banded spherulite is formed, which is ascribed to structural discontinuity caused by a rhythmic radial growth. For the 50:50 M‐PAEK/PEEK blend, ring‐banded spherulites and individual PEEK spherulites coexist in the system. In the blends with PEEK as the predominant component, M‐PAEK is rejected into the boundary of PEEK spherulites. The cooling rate and crystallization temperature have great effect on the phase behavior, especially the ring‐banded spherulite formation in the blends. In addition, the effects of M‐PAEK phase transition rate and phase separation rate on banded spherulite formation is discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3011–3024, 2007