LES of turbulent heat transfer: proper convection numerical schemes for temperature transport

Large eddy simulations of two basic configurations (decay of isotropic turbulence, and the academic plane channel flow) with heat transfer have been performed comparing several convection numerical schemes, in order to discuss their ability to evaluate temperature fluctuations properly. Results are compared with the available incompressible heat transfer direct numerical simulation data. It is shown that the use of regularizing schemes (such as high order upwind type schemes) for the temperature transport equation in combination with centered schemes for momentum transport equation gives better results than the use of centred schemes for both equations. Copyright © 2004 John Wiley & Sons, Ltd.     

Mesoscopic details of crack tip deformation field by application of differential interference contrast method

An experimental method is developed to examine the near tip deformation at the mesoscopic scale level. The differential interference contrast (DIC) method is used by application of the Nomarski prism in polarized microscope for measuring the out of surface deformation. The method is very sensitive to small height changes detected by different interference color. Discussed are results for the crack tip deformation field.     

Structural developments in synthetic rubbers during uniaxial deformation by in situ synchrotron X‐ray diffraction

The molecular orientation and strain‐induced crystallization of synthetic rubbers—polyisoprene rubber, polybutadiene rubber, and butyl rubber [poly(isobutylene isoprene)]—during uniaxial deformation were studied with in situ synchrotron wide‐angle X‐ray diffraction. The high intensity of the synchrotron X‐rays and the new data analysis method made it possible to estimate the mass fractions of the strain‐induced crystals and amorphous chain segments in both the oriented and unoriented states. Contrary to the conventional concept, the majority of the molecules (50–75%) remained in an unoriented amorphous state at high strains. Each synthetic rubber showed a different behavior of strain‐induced crystallization and molecular orientation during extension and retraction. Our results confirmed the occurence of strain‐induced networks in the synthetic rubbers due to the inhomogeneity of the crosslink distribution. The strain‐induced networks containing microfibrillar crystals and oriented amorphous tie chains were responsible for the ultimate mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 956–964, 2004     

Toughness mechanism in polypropylene composites: Polypropylene toughened with elastomer and calcium carbonate

Polypropylene (PP) was modified with elastomer or CaCO₃ particles of two different sizes (1 μm and 50 nm) in various volume fractions. The dispersion morphology and mechanical properties of the two systems were investigated as functions of the particle size and volume fraction of the modifier. The brittle‐to‐tough transition occurred when the matrix ligament thickness was less than the critical ligament thickness, which was about 0.1 μm for the PP used here, being independent of the type of modifier. At the same matrix ligament thickness, the improvement of the toughness was obviously higher with the elastomer rather than with CaCO₃, but adding CaCO₃ increased the modulus of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1656–1662, 2004     

On the influence of the surfactant''s polar group on the local and terminal velocities of bubbles

The local and the terminal velocities, the size and the degree of bubbles’ shape deformations were determined as a function of distance from the position of the bubble formation (capillary orifice) in solutions of n-octyltrimethylammonium bromide, n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside and n-octanoic acid.

These surface-active compounds have different polar groups but an identical hydrocarbon chain (C8) in the molecule. The motion of the bubbles was monitored and recorded using a stroboscopic illumination, a CCD camera, and a JVC professional video. The recorded bubble images were analyzed by the image analysis software. The bubbles accelerated rapidly and their shape was deformed immediately after detachment from the capillary. The extent of the bubbles’ shape deformation (ratio of horizontal and vertical diameters) was 1.5 in distilled water and dropped rapidly down to a level of ca. 1.05–1.03 with increasing surfactant concentration. After the acceleration period the bubbles either attained a constant value of the terminal velocity (distilled water and high concentrations of the solutions), or a maximum in the velocity profiles was observed (low concentrations). The values of the terminal velocity diminished drastically with increasing concentration, from the value of 35 cm/s in water down to about 15 cm/s, while the bubble diameter decreased by ca. 10% only. The surfactant adsorption at the surface of the bubbles was evaluated and the minimum adsorption coverages required to immobilize the bubbles’ surface were determined. It was found that this minimum adsorption coverage was ca. 4% for n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside, n-octanoic acid and 25% for n-octyltrimethylammonium bromide. The difference in the adsorption coverage together with the surfactants’ surface activities indicate that it is mainly the adsorption kinetics of the surfactants that governs the fluidity of interfaces of the rising bubbles.     

Large deviations and the generalized processor sharing scheduling for a two-queue system

We establish the optimal asymptotic decay rate of per-session queue length tail distributions for a two-queue system where a single constant rate server serves the two queues using the Generalized Processor Sharing (GPS) scheduling discipline. The result is obtained using the sample-path large deviation principle and has implications in call admission control for high-speed communication networks. This revised version was published online in June 2006 with corrections to the Cover Date.     

Adaptive remeshing for ductile fracture prediction in metal formingRemaillage adaptatif pour la prévision de la rupture ductile en mise en forme

The analysis of mechanical structures using the Finite Element Method in the framework of large elastoplastic strain, needs frequent remeshing of the deformed domain during computation. Indeed, the remeshing is due to the large geometrical distortion of finite elements and the adaptation to the physical behavior of the solution. This paper gives the necessary steps to remesh a mechanical structure during large elastoplastic deformations with damage. An important part of this process is constituted by geometrical and physical error estimates. The proposed method is integrated in a computational environment using the ABAQUS/Explicit solver and the BL2D-V2 adaptive mesher. To cite this article: H. Borouchaki et al., C. R. Mecanique 330 (2002) 709–716.     

Ergodic theory and the Strong Law of Large Numbers on Riesz spaces

In [W.-C. Kuo, C.C.A. Labuschagne, B.A. Watson, Discrete-time stochastic processes on Riesz spaces, Indag. Math. (N.S.) 15 (3) (2004) 435-451], we introduced the concepts of conditional expectations, martingales and stopping times on Riesz spaces. Here we formulate and prove order theoretic analogues of the Birkhoff, Hopf and Wiener ergodic theorems and the Strong Law of Large Numbers on Riesz spaces (vector lattices).     

Convergence Rates in the Law of Large Numbers under Sublinear Expectations

In this note, we study convergence rates in the law of large numbers for independent and identically distributed random variables under sublinear expectations. We obtain a strong L^p-convergence version and a strongly quasi sure convergence version of the law of large numbers.     

Review and complements on mixed-hybrid finite element methods for fluid flows

Mixed and hybrid finite element methods for the resolution of a wide range of linear and nonlinear boundary value problems (linear elasticity, Stokes problem, Navier–Stokes equations, Boussinesq equations, etc.) have known a great development in the last few years. These methods allow simultaneous computation of the original variable and its gradient, both of them being equally accurate. Moreover, they have local conservation properties (conservation of the mass and the momentum) as in the finite volume methods.The purpose of this paper is to give a review on some mixed finite elements developed recently for the resolution of Stokes and Navier–Stokes equations, and the linear elasticity problem. Further developments for a quasi-Newtonian flow obeying the power law are presented.