无机胶体法制备Pt/C催化剂及其性能表征

采用无机胶体法制备用于质子交换膜燃料电池(PEMFC)的Pt/C催化剂。研究了影响PtO₂胶体生成和稳定性的因素(溶液的pH值、浓度和温度条件等)以及不同还原剂浓度对Pt/C催化剂性能的影响。透射电子显微镜测试结果表明，采用经优化的工艺条件所制备的Pt/C催化剂平均粒径为3 nm，且分散性好、粒度均匀。X-射线衍射分析表明，催化剂中Pt(111)晶面的相对含量较高，有利于加速氧还原反应。单体PEMFC的电压/电流密度曲线测试表明，所制备的Pt/C催化剂具有良好的电化学性能。     

NdOx作为助催化剂对PtRu/C电催化氧化甲醇活性的影响

采用沉积-还原法制备了PtRu-NdOx/C催化剂, 借助TEM、EDS和XRD等测试手段对其进行了微结构和组成的表征. 结果表明, 催化剂中Pt与Ru以合金形式存在, 而Nd的氧化物则以无定形形态存在. 催化剂粒子的平均粒径在2 nm左右, 晶胞参数为0.3896 nm, Nd氧化物的加入对PtRu合金的晶体结构影响不明显. 采用循环伏安法和计时电流法, 比较了PtRu-NdOx/C催化剂和PtRu /C催化剂对甲醇氧化的电催化活性, 结果表明, 加入Nd的氧化物作为助催化剂能明显提高PtRu /C催化剂对甲醇氧化的电催化性能.     

直接甲醇燃料电池阴极电催化剂的研究进展

直接甲醇燃料电池(DMFC)功率密度高，燃料甲醇价格低廉、储存和携带方便，特别适合作为电动车和小型电子设备的电源，是目前燃料电池研究领域的一个热点。本文介绍了40年来DMFC阴极电催化剂的发展历史及现状，并针对目前严重影响DMFC性能的“甲醇透过”问题，阐述了研制耐甲醇阴极电催化剂的重要性，讨论了今后DMFC阴极电催化剂的发展趋势。     

吸热碳氢燃料裂解镧改性混合型催化剂的研究

制备了吸热型碳氢燃料NNJ-150和镧离子交换改性的USY、ZSM-5分子重申及混合分子筛，考察了NNJ-150在USHY、HZSM-5和两者混合物以及镧改性单分子筛和混合分子筛催化剂上的裂解反应。结果表明，ZSM-5分子筛中添加镧，对NNJ-150的单分子裂解反应有明显影响；混合分子两种分子筛之间存在协同作用，低温（500℃）下，LaUSY LaZSM-5（75：25）混合分子筛对低碳烯烃的选择性较高（41.48％），催化剂寿命较长（35min以上），能有效提高吸热型碳氢燃料NNJ-150的吸热能效。     

Cellulose-precursor synthesis of nanocrystalline Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>2−δ</Subscript> for SOFC anodes

Developments of intermediate-temperature solid oxide fuel cells (IT SOFCs) require novel anode materials with a high electrochemical activity at 800–1070 K. The polarization of cermet anodes, made of nickel, ceria and yttria-stabilized zirconia (YSZ) and applied onto a YSZ solid electrolyte, can be significantly reduced by catalytically active ceria additions, the relative role of which increases with decreasing temperature. Further improvement is observed when using Ce_0.8Gd_0.2O_2– (CGO) having a high oxygen ionic conductivity instead of undoped ceria, owing to enlargement of the electrochemical reaction zone. Nanocrystalline CGO powders with grain sizes of 8–35 nm were thus synthesized via the cellulose-precursor technique and introduced into Ni–CGO–YSZ cermets, and tested in contact with a (La_0.9Sr_0.1)_0.98Ga_0.8Mg_0.2O_3– (LSGM) electrolyte at 873–1073 K. The results showed that the anode performance can be enhanced by additional surface activation, in particular by impregnation with a Ce-containing solution, and also by incorporation of YSZ, which probably acts as a cermet-stabilizing component. The overpotential of the surface-modified Ni–CGO (25 wt%–75 wt%) anode in a 10% H₂/90% N₂ atmosphere was approximately 110 mV at 1073 K with a current density of 200 mA/cm².Presented at the OSSEP Workshop Ionic and Mixed Conductors: Methods and Processes, Aveiro, Portugal, 10–12 April 2003     

四氢呋喃-水-乙醇三元溶液体系制备高合金化Pt-Ru/CMK-3催化剂

提出了在四氢呋喃(THF)、H2O和乙醇三元体系中用一般的化学还原法在室温下制备高合金化Pt-Ru/CMK-3催化剂的新方法. 与在纯水中制得的商品化ETEK催化剂相比, 其Pt-Ru粒子的合金化程度高、平均粒径较小且相对结晶度低, 因此, 该催化剂对甲醇氧化的电催化活性远高于在纯水中制得的Pt-Ru催化剂. 高合金化程度的原因是H2PtCl6和RuCl3在THF、H2O和乙醇三元溶液体系中的起始还原电位相近. 此外, CMK-3以其规整的二维有序孔道结构, 为直接甲醇燃烧电池(DMFC)中电子和物质的传输提供了方便的路径, 其巨大的比表面积也为Pt-Ru 纳米粒子的均匀分散提供了良好的载体.     

Mass spectrometric analysis of ceramic components for solid oxide fuel cells

For the determination of trace impurities in ceramic components of solid oxide fuel cells (SOFCs), some mass spectrometric methods have been applied such as spark source mass spectrometry (SSMS), laser ionization mass spectrometry (LIMS), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and inductively coupled plasma mass spectrometry (ICP-MS). Due to a lack of suitable standard reference materials for quantifying of analytical results on La _x Sr _y MnO₃ cathode material a matrix-matched synthetic standard-high purity initial compounds doped with trace elements-was prepared in order to determine the relative sensitivity coefficients in SSMS and LA-ICP-MS. Radiofrequency glow discharge mass spectrometry (rf-GDMS) was developed for trace analysis and depth profiling of thick non-conducting layers. Surface analytical techniques, such as secondary ion mass spectrometry (SIMS) and sputtered neutral mass spectrometry (SNMS), were used to determine the element distribution on surfaces (homogeneity) and the surface contaminants of SOFC ceramic layers.Dedicated to Professor Dr. rer. nat. Hubertus Nickel on the occasion of his 65th birthday     

Pre-irradiation induced grafting of styrene into crosslinked and non-crosslinked polytetrafluoroethylene films for polymer electrolyte fuel cell applications. II: Characterization of the styrene grafted films

Crosslinked and non-crosslinked polytetrafluoroethylene films (RX-PTFE and V-PTFE films, respectively) were irradiated by γ-ray and then grafted with styrene in liquid phase. Microscope FT-IR spectroscopy, TGA, solid state ¹³C CP/MAS and high resolution HS/MAS NMR spectroscopy, wide-angle X-ray diffraction (WAXD) study were used to get the structural information of the styrene grafted RX-PTFE and V-PTFE films. From microscope FT-IR spectra of the grafted RX-PTFE films, the “grafting front mechanism” was proved. TGA analysis showed that the grafted films have a small degradation step and two main degradation steps. In the ¹³C CP/MAS NMR spectra of the non-grafted films, there are no signal due to the absence of the hydrogen atom. While in the spectra of the grafted films, there are signals attributed to the polystyrene grafts. In the ¹³C HS/MAS NMR spectra of the grafted films, the relative intensity of the peaks attributed to the polystyrene grafts increased while the relative intensity of the peak attributed to PTFE matrix decreased with the increase in the DOG. From WAXD patterns, the intensity of the crystalline peak decrease with the increase in the DOG. The grafted films were sulfonated by chlorosulfonic acid and the results of highest IEC value exceeded 3.0. Those results will be reported in the near future.     

BaCe0.8Ho0.2O3-a陶瓷的性质与应用

Ceramic BaCe0.8Ho0.2O3-α with orthorhombic perovskite structure was prepared by conventional solid state reaction, and its conductivity and ionic transport number were measured by ac impedance spectroscopy and gas concentration cell methods in the temperature range of 600-1000 ℃ in wet hydrogen and wet air, respectively. Using the ceramics as solid electrolyte and porous platinum as electrodes, the hydrogen-air fuel cell was constructed, and the cell performance at temperature from 600-1000 ℃ was examined. The results indicate that the specimen was a pure protonic conductor with the protonic transport number of 1 at temperature from 600-900 ℃ in wet hydrogen, a mixed conductor of proton and electron with the protonic transport number of 0.99 at 1000 ℃. The electronic conduction could be neglected in this case, thus the total conductivity in wet hydrogen was approximately regarded as protonic conductivity. In wet air, the specimen was a mixed conductor of proton, oxide ion and electron hole. The protonic transport numbers were 0.01-0.09, and the oxide-ionic transport numbers were 0.27-0.32. The oxide ionic conductivity was increased with the increase of temperature, but the protonic conductivity displayed a maximum at 900 ℃, due to the combined increase in mobility and depletion of the carriers. The fuel cell could work stably. At 1000 ℃, the maximum short-circuit current density and power output density were 346 mA/cm^2 and 80 mW/cm^2, respectively.     

Energetics of magnesium, strontium, and barium doped lanthanum gallate perovskites

LaGaO₃ perovskites doped with Sr or Ba at the La site and Mg at the Ga site were prepared by solid-state reaction or sol-gel method and characterized. Enthalpies of formation from constituent oxides at 298 K were determined by high-temperature oxide melt solution calorimetry. Energetic trends are discussed in terms of defect chemistry. As oxygen deficiency increases, formation enthalpies define three trends, LaGa_1−yMg_yO_3−δ (LGM), La_1−xSr_xGa_1−yMg_yO_3−δ (LSGM), and La_1−xBa_xGa_1−yMg_yO_3−δ (LBGM). They become less exothermic with increasing doping, suggesting a dominant destabilization effect from oxygen vacancies. The endothermic enthalpy of vacancy formation is 275±37, 166±18 and 138±12 kJ/mol of V_O^·· for LGM, LBGM and LSGM, respectively. Tolerance factor and ion size mismatch also affect enthalpies. In terms of energetics, Sr is the best dopant for the La site and Mg for the Ga site, supporting earlier studies, including oxygen ion conductivity and computer modeling.