溶胶-凝胶-硫化法制备硅橡胶吸附萃取搅拌棒

采用溶胶-凝胶-硫化法,以甲基乙烯基硅橡胶和乙烯基封端硅橡胶为原料制备了厚壁硅橡胶吸附萃取搅拌棒(stir bar for sorptive extraction,SBSE)。采用分段硫化和多阶程序升温老化防止涂层脱落和龟裂,一次涂渍涂层厚度约150~250μm,280℃下无流失,使用寿命可达150次。利用所制备涂层,结合自制热解析系统(thermal desorption system,TDS),建立了SBSE-TDS-CGC-FID测定水样中6种多环芳烃(polyaromatichydrocarbons,PAHs)的方法。方法的线性范围为0.3~1000μg/L,检出限为0.002~0.011μg/L,相对标准偏差在0.92%~6.14%之间。该方法能够满足欧盟2005/69/EC指令对多环芳烃低于10 mg/kg的检测要求。     

Fe3O4@C Nanotubes Grown on Carbon Fabric as a Free-Standing Anode for High-Performance Li-Ion Batteries

Recently, Li-ion batteries (LIBs) have attracted extensive attention owing to their wide applications in portable and flexible electronic devices. Such a huge market for LIBs has caused an ever-increasing demand for excellent mechanical flexibility, outstanding cycling life, and electrodes with superior rate capability. Herein, an anode of self-supported Fe₃O₄@C nanotubes grown on carbon fabric cloth (CFC) is designed rationally and fabricated through an in situ etching and deposition route combined with an annealing process. These carbon-coated nanotube structured Fe₃O₄ arrays with large surface area and enough void space can not only moderate the volume variation during repeated Li⁺ insertion/extraction, but also facilitate Li⁺/electrons transportation and electrolyte penetration. This novel structure endows the Fe₃O₄@C nanotube arrays stable cycle performance (a large reversible capacity of 900 mA h g⁻¹ up to 100 cycles at 0.5 A g⁻¹) and outstanding rate capability (reversible capacities of 1030, 985, 908, and 755 mA h g⁻¹ at 0.15, 0.3, 0.75, and 1.5 A g⁻¹, respectively). Fe₃O₄@C nanotube arrays still achieve a capacity of 665 mA h g⁻¹ after 50 cycles at 0.1 A g⁻¹ in Fe₃O₄@C//LiCoO₂ full cells.     

Different approaches toward an automatic structural alignment of drug molecules: Applications to sterol mimics,thrombin and thermolysin inhibitors

Summary A relative comparison of the binding properties of different drug molecules requires their mutual superposition with respect to various alignment criteria. In order to validate the results of different alignment methods, the crystallographically observed binding geometries of ligands in the pocket of a common protein receptor have been used. The alignment function in the program SEAL that calculates the mutual superposition of molecules has been optimized with respect to these references. Across the reference data set, alignments could be produced that show mean rms deviations of approximately 1 Å compared to the experimental situation. For structures with obvious skeletal similarities a multiple-flexible fit, linking common pharmacophoric groups by virtual springs, has been incorporated into the molecular mechanics program MOMO. In order to combine conformational searching with comparative alignments, the optimized SEAL approach has been applied to sets of conformers generated by MIMUMBA, a program for conformational analysis. Multiple-flexible fits have been calculated for inhibitors of ergosterol biosynthesis. Sets of different thrombin and thermolysin inhibitors have been conformationally analyzed and subsequently aligned by a combined MIMUMBA/SEAL approach. Since for these examples crystallographic data on their mutual alignment are available, an objective assessment of the computed results could be performed. Among the generated conformers, one geometry could be selected for the thrombin and thermolysin inhibitors that approached reasonably well the experimentally observed alignment.     

Hydroquinone oxidation catalyzed by pyridine–Cu(II) complexes attached to polyorganosiloxane. II. Elucidation of factors related to catalytic activity

The oxidation of hydroquinone catalyzed by pyridine-Cu(II) complexes attached to polyorganosiloxane was investigated in the mixed solvent of methanol/water (vol. ratio 2/1). The catalytic oxidation followed Michaelis-Menten-like kinetics. The large k₂ term related to a turnover number indicated that the present polymeric catalysts have a remarkable effect on the activation process. The methylene number between the side-chain acid amido and pyridyl groups of the polymeric ligand was shown to be closely related to the appearance of hydrophobic effects in both the substrate-binding and the activation processes as deduced from the Michaelis constant and the thermodynamic and activation parameters. The binding parameters for 4-methoxyphenol with pyridyl-functionalized polyorganosiloxanes supported that the flexible backbone is also effective in the oxidation of hydroquinone. The Cu(II) complexes with pyridyl-functionalized polyorganosiloxane would have the structures distorted from square planar formation, which would promote the reduction of Cu(II) to Cu(I), as concluded from ESR spectroscopy and electrochemical measurement. © 1994 John Wiley & Sons, Inc.     

Development of a carbon‐nanoparticle‐coated stirrer for stir bar sorptive extraction by a simple carbon deposition in flame

Stir bar sorptive extraction is an environmentally friendly microextraction technique based on a stir bar with various sorbents. A commercial stirrer is a good support, but it has not been used in stir bar sorptive extraction due to difficult modification. A stirrer was modified with carbon nanoparticles by a simple carbon deposition process in flame and characterized by scanning electron microscopy and energy‐dispersive X‐ray spectrometry. A three‐dimensional porous coating was formed with carbon nanoparticles. In combination with high‐performance liquid chromatography, the stir bar was evaluated using five polycyclic aromatic hydrocarbons as model analytes. Conditions including extraction time and temperature, ionic strength, and desorption solvent were investigated by a factor‐by‐factor optimization method. The established method exhibited good linearity (0.01–10 μg/L) and low limits of quantification (0.01 μg/L). It was applied to detect model analytes in environmental water samples. No analyte was detected in river water, and five analytes were quantified in rain water. The recoveries of five analytes in two samples with spiked at 2 μg/L were in the range of 92.2–106% and 93.4–108%, respectively. The results indicated that the carbon nanoparticle‐coated stirrer was an efficient stir bar for extraction analysis of some polycyclic aromatic hydrocarbons.     

Sol–gel coating of poly(ethylene glycol)‐grafted multiwalled carbon nanotubes for stir bar sorptive extraction and its application to the analysis of polycyclic aromatic hydrocarbons in water

Poly(ethylene glycol) grafted onto carboxyl‐terminated multi‐walled carbon nanotubes were prepared by the sol–gel technique as a stationary phase for stir bars. The analytical methodology included stir bar sorptive extraction with micellar desorption followed by liquid chromatography. Polycyclic aromatic hydrocarbons were used as the model compounds to evaluate the extraction performance. The extraction efficiency, for the determination of polycyclic aromatic hydrocarbons from water samples, was optimized based on a chemometrics approach. The effect of the experimental parameters on the extraction response was investigated and the optimum extraction conditions were selected. Under the optimum conditions, the proposed method showed a good linearity within the different ranges for different analytes (e.g. 0.05–500 ng/mL for phenanthrene), a square of the correlation coefficient was higher than 0.999, and an appropriate limit of detection in the range of 0.013–0.072 ng/mL. The recoveries in all cases were above 94%, with relative standard deviations below 2.4%.     

Combination of sorption properties of polydimethylsiloxane and solid‐phase extraction sorbents in a single composite material for the passive sampling of polar and apolar pesticides in water

Passive sampling techniques have been developed as an alternative method for in situ integrative monitoring of trace levels of neutral pesticides in environmental waters. The objective of this work was to develop a new receiving phase for pesticides with a wide range of polarities in a single step. We describe the development of three new composite silicone rubbers, combining polydimethylsiloxane mechanical and sorption properties with solid‐phase extraction sorbents, prepared as a receiving phase for passive sampling. A composite silicone rubber composed of polydimethylsiloxane/poly(divinylbenzene‐co‐N‐vinylpyrrolidone) was selected by batch experiments for its high sorption properties for pesticides with octanol‐water partition coefficients ranging from 2.3 to 5.5. We named this composite material “Polar/Apolar Composite Silicone Rubber”. A structural study by scanning electron microscopy confirmed the homogeneous dispersion of the sorbent particles and the encapsulation of particles within the polydimethylsiloxane matrix. We also demonstrate that this composite material is resistant to common solvents used for the back‐extraction of analytes and has a maximal resistance temperature of 350°C. Therefore, the characteristics of the “Polar/Apolar Composite Silicone Rubber” meet most of the criteria for use as a receiving phase for the passive sampling of pesticides.     

聚酰亚胺固相萃取搅拌棒的制备及其在环境水中酚类的分析应用

利用相转换法制备了聚酰亚胺吸附萃取搅拌棒,用5种有机酚作为评价标样,并与现有商品化吸附萃取搅拌棒进行比较。优化了萃取搅拌速度、溶液离子强度、萃取温度、萃取时间以及热解析温度和时间。在最佳实验条件下,100 mL 样品,30% NaCl,在25℃下,经活化5 min 后的聚酰亚胺吸附搅拌棒萃取30 min (800 r/ min),然后300℃热解析4 min,使目标物脱附,再进行色谱分析。目标物在大于两个数量级浓度范围内具有良好的线性(R≥0.9995),定量限(LOQ,S/ N=10)为0.028~0.123μg/ L,重复性为1.6%~9.7%。将SBSE 与气相色谱-质谱联用,对海水、自来水和污水中的酚类进行定性与定量分析,结果表明,聚酰亚胺吸附萃取搅拌棒具有良好的选择性,最高热解析温度350℃,在分析水中痕量极性化合物领域具有广阔应用前景。     

ICE Concentration Linked with Extractive Stirrer (ICECLES)

Trace and ultra-trace analysis can be difficult to achieve, especially for polar, more volatile, and/or thermally unstable analytes. A novel technique, coined ICE Concentration Linked with Extractive Stirrer (ICECLES), may help address this problem. The implementation of ICECLES described here combines stir bar sorptive extraction (SBSE) with freeze concentration (FC), where an aqueous solution is frozen during SBSE in order to concentrate analytes into a polydimethylsiloxane (PDMS) coated stir bar. Five test probe molecules with a range of log K_ows (2-butanol, benzyl alcohol, benzaldehyde, dimethyl trisulfide and bromobenzene) were prepared from aqueous solutions using ICECLES. Thermal desorption gas–chromatography mass–spectrometry was then used to quantify these analytes. Parameters affecting the performance of ICECLES (e.g., freeze rate) were evaluated, with extraction at lower speeds resulting in higher extraction efficiencies, whereas the freeze rate and initial analyte concentration only had a minor effect. ICECLES produced much higher extraction efficiencies than SBSE alone, with signal enhancements of up to 474× SBSE. ICECLES also provided excellent reproducibility and lower LODs than SBSE for all compounds tested. ICECLES performed well when used to analyze multiple triazine pesticides and breakdown products in environmental surface waters. Overall, the ICECLES technique was excellent at preparing aqueous samples for trace analysis and shows promise as a novel analytical sample preparation technology.     

Stir bar sorptive extraction with in situ derivatization and thermal desorption-gas chromatography-mass spectrometry for determination of chlorophenols in water and body fluid samples

A new method, stir bar sorptive extraction (SBSE) with in situ derivatization and thermal desorption (TD)-gas chromatography-mass spectrometry (GC-MS), which is used for the determination of trace amounts of chlorophenols, such as 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TrCP), 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP) and pentachlorophenol (PCP), in tap water, river water and human urine samples, is described. The derivatization conditions with acetic acid anhydride and the SBSE conditions such as extraction time are investigated. Then, the stir bar is subjected to TD followed by GC-MS. The detection limits of the chlorophenols in tap water, river water and human urine samples are 1-2, 1-2, and 10-20 pg ml⁻¹ (ppt), respectively. The calibration curves for the chlorophenols are linear and have correlation coefficients higher than 0.99. The average recoveries of the chlorophenols in all the samples are higher than 95% (R.S.D. < 10%) with correction using added surrogate standards, 2,4-dichlorophenol-d₅, 2,4,6-trichlorophenol-¹³C₆, 2,3,4,6-tetrachlorophenol-¹³C₆ and pentachlorophenol-¹³C₆. This simple, accurate, sensitive and selective analytical method may be applicable to the determination of trace amounts of chlorophenols in liquid samples.