Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

广义复合隐迭代格式逼近非扩张映像公共不动点

提出并使用如下广义复合隐迭代格式逼近非扩张映像族{Ti}Ni=1公共不动点:{xn=αnxn-1 (1-αn)Tnyn,yn=rnxn snxn-1 tnTnxn wnTnxn-1,rn sn tn wn=1,{αn},{rn},{sn},{tn},{wn}∈[0,1],这里Tn=TnmodN.该文提出的广义复合隐迭代格式包含了目前多种迭代格式,因此,所得强弱收敛定理推广及发展了Mann,Ishikawa,XuandOri,等许多作者的结果.     

Transfer matrix approach of vibration isolation analysis of periodic composite structure

The transmission properties of elastic waves propagating in a three-dimensional composite structure embedded periodically with spherical inclusions are analyzed by the transfer matrix method in this paper. Firstly, the periodic composite structures are divided into many layers, the transfer matrix of monolayer structure is deduced by the wave equations, and the transfer matrix of the entire structure is obtained in the case of boundary conditions of displacement and stress continuity between layers. Then, the effective impedance of the structure is analyzed to calculate its reflectivity and transmissivity of vibration isolation. Finally, numerical simulation is carried out; the experiment results validate the accuracy and feasibility of the method adopted in the paper and some useful conclusions are obtained. Project (No. 50075029) supported by the National Natural Science Foundation of China.     

Nanoparticle composites: FePt with wide-band-gap semiconductor

We present a simple way to synthesize FePt and ZnO (wide-band-gap semiconductor) nanoparticle composites. The FePt nanoparticles were fabricated using the method reported by Sun et al. By controlling the heating rate, 3 nm FePt nanoparticles were synthesized. Well-dispersed FePt and ZnO nanoparticle composites were prepared by further adding zinc acetate and oleyl amine into the 3 nm FePt nanoparticle dispersion. By controlling the molar ratio of the FePt and zinc acetate, FePt and ZnO nanoparticle composites with different FePt particle fractions were obtained. The intensity of photo luminescence spectra of the nanoparticle composites increases very much with decreasing FePt particle fraction, whereas the peak position shifts a little. After annealing at 550 °C for half an hour, the nanoparticle composites become magnetically hard or semi-hard with coercivity much dependent on the FePt particle volume fraction. The coercivity of the composites increases with annealing temperature. The composites hold the promise of applications in new generation recording and/or optical devices.     

Influence of silicon on the microstructure and mechanical properties of Zr-Si-N composite films

A series of Zr-Si-N composite films with different Si contents were synthesized in an Ar and N₂ mixture atmosphere by the bi-target reactive magnetron sputtering method. These films’ composition, microstructure and mechanical properties were characterized by energy dispersive spectroscopy, X-ray diffraction, scanning electron microscopy, atomic force microscopy and nanoindentation. Experimental results revealed that after the addition of silicon, Si₃N₄ interfacial phase formed on the surface of ZrN grains and prevented them from growing up. Zr-Si-N composite films were strengthened at low Si content with the hardness and elastic modulus reaching their maximum values of 29.8 and 352 GPa at 6.2 at% Si, respectively. With a further increase of Si content, the crystalline Zr-Si-N films gradually transformed into amorphous, accompanied with a remarkable fall of films’ mechanical properties. This limited enhancement of mechanical properties in the Zr-Si-N films may be due to the low wettability of Si₃N₄ on the surface of ZrN grains.     

ZnSe/SiO2复合薄膜光学常数与荧光光谱的研究

采用溶胶-凝胶工艺与原位生长技术，制备了ZnSe/SiO₂复合薄膜.X射线衍射分 析表明薄膜中ZnSe晶体呈立方闪锌矿结构.X射线荧光分析结果显示薄膜中Zn与Se摩尔比为1 ∶1.01—1∶1.19.利用场发射扫描电子显微镜观察了复合薄膜的表面形貌，结果表明复合薄 膜表面既存在尺寸约为400nm的ZnSe晶粒，也存在尺寸小于100nm的ZnSe晶粒.利用椭偏仪测 量了薄膜椭偏角Ψ，Δ与波长λ的关系，采用Maxwell-Garnett有效介质理论对薄膜的光学 常数、厚度、气孔率、ZnS 关键词： 2复合薄膜')" href="#">ZnSe/SiO₂复合薄膜 光学性质 椭偏光度法 荧光光谱     

Co-Orthogonal Codes

We define, construct and sketch possible applications of a new class of non-linear codes: co-orthogonal codes, with possible applications in cryptography and parallel processing. We also describe a fast and general method for generating (non-linear) codes with prescribed dot-products with the help of multi-linear polynomials.     

Electrolytical production of Ni + Mo + Si composite coatings with enhanced content of Si

Ni + Mo + Si composite coatings were prepared by co-deposition of nickel with molybdenum and silicon powders from a nickel solution in which Mo and Si particles were suspended by stirring. The layers have been deposited on a carbon steel substrate (St3S) under galvanostatic conditions. The content of Si in deposited layers was about 2-5 wt.% depending on deposition current density and the value of electric charge. For comparison Ni + Mo composite coatings were obtained under analogous current conditions. Composite coatings of enhanced Si content (15 wt.%) were deposited from an electrolyte in which 40 g/dm³ of Si covered with electroless plated nickel was dispersed. Deposition current density was equal 0.1 A/cm² and the value of electric charge Q = 500 C/cm². The thickness of the coatings was about 100-300 μm depending on their kind, electric charge and the deposition current density. Surface and cross-section morphology were investigated by scanning electron microscope (SEM). All deposited coatings are characterized by great, developed surface area. No internal stresses causing their cracking were observed. Chemical composition of the layers was determined by X-ray fluorescence spectroscopy (XRF) method and quantitative X-ray analysis (QXRD). It was stated, that the content of molybdenum and silicon in Ni + Mo + Si coatings depends on deposition current density and the amount of the powder in bath. The results of structural investigation of the obtained layers by the X-ray diffraction (XRD) method show, that they consist in crystalline Mo or Mo and Si phases built into Ni matrix. Moreover, Ni + Mo + Si composite coatings were modified by thermal treatment. It has been found that the thermal treatment of Ni + Mo + Si composite coatings caused that the new phases (NiSi, Mo₂Ni₃Si and Ni₆Mo₆C_1.06) were obtained.     

含氰基的酚醛树脂及其碳纤维复合材料

含氰基的酚醛树脂，具有优异的耐高温性能和高温下的机械强度，在３１５℃下性能变化甚小；不着火，发烟量低，有良好的加工成型性能。热固化过程中氰基成三嗪环而交联，没有小分子脱出，是一类具有广泛发展前景的新型热固性树脂。     

A STUDY OF J-INTEGRAL OF THE ORTHOTROPIC COMPOSITE MATERIAL

ＡＳＴＵＤＹＯＦＪ－ＩＮＴＥＧＲＡＬＯＦＴＨＥＯＲＴＨＯＴＲＯＰＩＣＣＯＭＰＯＳＩＴＥＭＡＴＥＲＩＡＬＷａｎｇＡｉ－ｑｉｎ（王蔼勤）；ＦｅｎｇＢａｏ－ｌｉａｎ（冯宝莲）；ＹａｎｇＷｅｉ－ｙａｎｇ（杨维阳）（ＴａｉｙｕａｎＨｅａｖｙＭａｃｈｉｎｅｒｙ．...