Buck变换器的输出短路火花放电能量及输出本质安全判据

为得出Buck变换器的输出本质安全判据, 基于安全火花试验装置, 对其输出短路火花放电特性进行了试验研究, 发现其放电过程可分为介质击穿、火花产生、火花维持和火花熄灭四个阶段.基于得出的火花放电特性, 对其输出短路火花放电能量进行了深入分析, 指出对于给定电感的Buck变换器, 当负载电阻 R_L小于给定电感对应的临界电阻R_LC时, 火花放电能量是关于R_L的凹函数; 而在R_L > R_LC时, 是关于R_L的凸函数.考虑到实际的参数取值范围, 进一步指出: R_L < R_LC时的火花放电能量随R_L的增加而增大, 且在R_L=R_LC时达到最大值; 而在R_L > R_LC时, 则随着R_L的增加, 先增大后减小, 在增加到特征电阻R_{L, DCM}时达到最大值. 得出了变换器在全动态范围内的最危险工况: 变换器在输入电压最高及负载电阻等于R_{L, DCM} 时工作于DCM, 此时, 短路火花放电能量达到最大值.基于能量等效, 提出了可模拟变换器输出短路放电特性的等效简单电容电路及输出本质安全判据, 仿真和试验结果验证了理论分析及所提出判据的正确性和可行性. 关键词： Buck变换器 本质安全 短路火花放电能量 输出本质安全判据     

两种带电尘埃颗粒的等离子体鞘层玻姆判据

采用流体方程和尘埃充电自洽模型研究了鞘边含有两种尘埃颗粒的等离子体玻姆判据. 通过拟牛顿法数值模拟了鞘边两种尘埃颗粒的存在对尘埃自身充电以及离子马赫数的影响. 两种尘埃颗粒中含量较少的尘埃颗粒数密度的增加, 导致两种尘埃颗粒表面悬浮势一个降低, 一个升高. 含量较少的尘埃颗粒的数密度越多和半径越小, 都会导致离子马赫数增大. 另外鞘边无论何种尘埃颗粒的速度增加, 鞘边离子马赫数都将减小. 关键词： 等离子体鞘层 尘埃颗粒 玻姆判据     

Multi-sample cluster analysis using Akaike's Information Criterion

Summary Multi-sample cluster analysis, the problem of grouping samples, is studied from an information-theoretic viewpoint via Akaike's Information Criterion (AIC). This criterion combines the maximum value of the likelihood with the number of parameters used in achieving that value. The multi-sample cluster problem is defined, and AIC is developed for this problem. The form of AIC is derived in both the multivariate analysis of variance (MANOVA) model and in the multivariate model with varying mean vectors and variance-covariance matrices. Numerical examples are presented for AIC and another criterion calledw-square. The results demonstrate the utility of AIC in identifying the best clustering alternatives. This research was supported by Office of Naval Research Contract N00014-80-C-0408, Task NR042-443 and Army Research Office Contract DAAG 29-82-K-0155, at the University of Illinois at Chicago.     

Notch fatigue of Cu_(50)Zr_(50) metallic glasses under cyclic loading: molecular dynamics simulations

Molecular dynamics simulation is performed to simulate the tension–compression fatigue of notched metallic glasses(MGs), and the notch effect of MGs is explored. The notches will accelerate the accumulation of shear transition zones, leading to faster shear banding around the notches' root causing it to undergo severe plastic deformation. Furthermore, a qualitative investigation of the notched MGs demonstrates that fatigue life gradually becomes shorter with the increase in sharpness until it reaches a critical scale. The fatigue performance of blunt notches is stronger than that of sharp notches. Making the notches blunter can improve the fatigue life of MGs.     

中立型方程x(t)+cx(t-ㄒ)+ax(t)+bx(t-ㄒ)=0零解渐近稳定的代数判据

本文建立了方程ｘ（ｔ）＋ｃｔ（ｔ－ｔ）＋ａｘ（ｔ）＋ｂｘ（ｔ－ｔ）＝０零解渐近稳定的充要条件,给出了其零解渐近稳定的代数判据,同时纠正了文［２］中出现的错误．     

Warm tachyon inflation and swampland criteria

In this study, the scenario of a two-component warm tachyon inflation is considered, where the tachyon field plays the role of the inflaton by driving the inflation. During inflation, the tachyon scalar field interacts with the other component of the Universe, which is assumed to be photon gas, i.e., radiation. The interacting term contains a dissipation coefficient, and the study is modeled based on two different and familiar choices of the coefficient that were studied in the literature. By employing the latest observational data, the acceptable ranges for the free parameters of the model are obtained. For any choice within the estimated ranges, there is an acceptable concordance between the theoretical predictions and observations. Although the model is established based on several assumptions, it is crucial to verify their validity for the obtained values of the free parameters of the model. It is found that the model is not self-consistent for all values of the ranges, and for some cases, the assumptions are violated. Therefore, to achieve both self-consistency and agreement with the data, the parameters of the model must be constrained. Subsequently, we consider the recently proposed swampland conjecture, which imposes two conditions on the inflationary models. These criteria rule out some inflationary models; however, warm inflation is among those that successfully satisfy the swampland criteria. We conduct a precise investigation, which indicates that the proposed warm tachyon inflation cannot satisfy the swampland criteria for some cases. In fact, for the first case of the dissipation coefficient, in which, there is dependency only on the scalar field, the model agrees with observational data. However, it is in direct tension with the swampland criteria. Nevertheless, for the second case, wherein the dissipation coefficient has a dependency on both the scalar field and temperature, the model exhibits acceptable agreement with observational data, and suitably satisfies the swampland criteria.     

Anti-Controlling Codimension-2 Bifurcation of Discrete Dynamical Systems in 1 : 2 Resonance北大核心CSCD

从分岔反控制的角度设计了一套非线性反馈控制策略,来实现离散动力系统1∶2共振情形下余维二分岔的各种分岔解。首先,针对传统分岔准则在确定高余维分岔点时存在的局限性,建立了一个1∶2共振情形下的余维二分岔的新显式准则,基于这个显式准则通过设计线性控制增益来确保此类余维二分岔的存在性。然后,推导了1∶2共振的中心流形,并基于范式方法通过设计非线性控制增益,分析了1∶2共振情形下余维二分岔解的类型和稳定性。最后,以一个Arneodo-Coullet-Tresser映射为例,在指定的参数点处通过控制实现了具有1∶2共振分岔特性的各种分岔解,进一步验证了理论分析。     

用概率断裂力学方法预测管状接头的疲劳寿命

本文研究了Ｔ型管状接头在面内和面外弯曲循环载荷作用下的疲劳强度问题，通过将材料常数和初始裂纹尺寸作为随机变量，采用ＭｏｎＣａｒｌｏ模拟方法对疲劳寿命进行了统计分析．同时，对计算结果进行了线性回归，并与实验结果作了比较。     

Which stresses affect the glide of screw dislocations in bcc metals?

By direct application of stress in molecular statics calculations we identify the stress components that affect the glide of 1/2?111? screw dislocations in bcc tungsten. These results prove that the hydrostatic stress and the normal stress parallel to the dislocation line do not play any role in the dislocation glide. Therefore, the Peierls stress of the dislocation cannot depend directly on the remaining two normal stresses that are perpendicular to the dislocation but, instead, on their combination that causes an equibiaxial tension-compression (and thus shear) in the plane perpendicular to the dislocation line. The Peierls stress of 1/2?111? screw dislocations then depends only on the orientation of the plane in which the shear stress parallel to the Burgers vector is applied and on the magnitude and orientation of the shear stress perpendicular to the slip direction.