Dynamic mechanical thermal analysis transitions of partially and fully substituted cellulose fatty esters

The main transitions of cellulose fatty esters with different degrees of substitution (DSs) were investigated with dynamic mechanical thermal analysis. Two distinct main relaxations were observed in partially substituted cellulose esters (PSCEs). They were attributed to the glass‐transition temperature and to the chain local motion of the aliphatic substituents. The temperatures of both transitions decreased when DS or the number of carbon atoms (n) of the acyl substituent increased. Conversely, all the transitions of fully substituted cellulose esters occurred within a narrow temperature range, and they did not vary significantly with n. This phenomenon was explained by the formation of a crystalline phase of the fatty substituents. The presence of few residual OH groups in PSCEs was responsible for a large increase in the storage bending modulus, and it eliminated the effect of n on damping. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 281–288, 2003     

A study on anisotropy of L2 to L3 Coster-Kronig transition (f23) for Th and U elements

The Coster-Kronig transition, f₂₃, was determined using differential fluorescence cross sections of L_l X-ray for Th and U. The targets were irradiated an Am-241 radioisotope at the different incident angle. The L_l X-rays were counted with a Si (Li) detector at the different scattering angle varying from 60° to 90° at 10° intervals. For each angle, the Coster-Kronig transition probability, f₂₃, was found. An obtained Coster-Kronig transition probability value was fitted versus emission angle. According to present results we can say that the Coster-Kronig transition probability, f₂₃, shows isotropic distribution.     

Numerical calculations of temperature distribution of double layer metallic surface treated by laser beams

A mathematical model of laser beam treatment of double layer alloys (Ni/Fe, Al/Fe and Cr/Fe systems) describing the effect of laser beam on different physical and geometrical parameters of coated layer system has been adapted. The numerical solutions of the non-homogeneous heat-transport differential equation could estimate the temperature of the treated region.The suggested model allows investigation of the temperature distribution as a function of treated surface and laser parameters. The physical parameters of the treated materials were taken as functions of temperature due to the change in the temperature of the treated double layer materials.     

2‐connected 7‐coverings of 3‐connected graphs on surfaces

An m‐covering of a graph G is a spanning subgraph of G with maximum degree at most m. In this paper, we shall show that every 3‐connected graph on a surface with Euler genus k ≥ 2 with sufficiently large representativity has a 2‐connected 7‐covering with at most 6k ? 12 vertices of degree 7. We also construct, for every surface F² with Euler genus k ≥ 2, a 3‐connected graph G on F² with arbitrarily large representativity each of whose 2‐connected 7‐coverings contains at least 6k ? 12 vertices of degree 7. © 2003 Wiley Periodicals, Inc. J Graph Theory 43: 26–36, 2003     

Standardization of Methods for Characterizing the Surface Geometry of Solids

Since a comprehensive survey published in 1999 [1] much work was done in standardizing measuring methods to characterize the surface geometry of dispersed and/or porous solids and to certify reference materials. The present paper is an extension of a short communication [2]. It gives a survey on existing standards and reports on new drafts and proposals.     

Viscoelastic properties of nanostructured natural rubber/polystyrene interpenetrating polymer networks

The effects of the blend ratio and initiating system on the viscoelastic properties of nanostructured natural rubber/polystyrene‐based interpenetrating polymer networks (IPNs) were investigated in the temperature range of ?80 to 150 °C. The studies were carried out at different frequencies (100, 50, 10, 1, and 0.1 Hz), and their effects on the damping and storage and loss moduli were analyzed. In all cases, tan δ and the storage and loss moduli showed two distinct transitions corresponding to natural rubber and polystyrene phases, which indicated that the system was not miscible on the molecular level. However, a slight inward shift was observed in the IPNs, with respect to the glass‐transition temperatures (T_g's) of the virgin polymers, showing a certain degree of miscibility or intermixing between the two phases. When the frequency increased from 0.1 to 100 Hz, the T_g values showed a positive shift in all cases. In a comparison of the three initiating systems (dicumyl peroxide, benzoyl peroxide, and azobisisobutyronitrile), the dicumyl peroxide system showed the highest modulus. The morphology of the IPNs was analyzed with transmission electron microscopy. The micrographs indicated that the system was nanostructured. An attempt was made to relate the viscoelastic behavior to the morphology of the IPNs. Various models, such as the series, parallel, Halpin–Tsai, Kerner, Coran, Takayanagi, and Davies models, were used to model the viscoelastic data. The area under the linear loss modulus curve was larger than that obtained by group contribution analysis; this showed that the damping was influenced by the phase morphology, dual‐phase continuity, and crosslinking of the phases. Finally, the homogeneity of the system was further evaluated with Cole–Cole analysis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1680–1696, 2003     

Second order parabolic equations in Banach spaces with dynamic boundary conditions

In this paper, we exhibit a unified treatment of the mixed initial boundary value problem for second order (in time) parabolic linear differential equations in Banach spaces, whose boundary conditions are of a dynamical nature. Results regarding existence, uniqueness, continuous dependence (on initial data) and regularity of classical and strict solutions are established. Moreover, several examples are given as samples for possible applications.

     

Modeling of the Kinetics of Intramolecular Processes and Transient Spectra with Allowance for Nonradiative Transitions

It has been shown that the kinetics of intramolecular processes and time-resolved spectra with allowance for the quantum beats of the resonant states of isomers or isolated subsystems of levels of one isomeric form can be described with the use of a molecular model interpreting the effect of beats as a nonradiative transition. We have obtained an expression for the nonradiative transition probability, which is directly proportional to the beat frequency and depends oscillatorily on time, thus modeling the effect of beats. The parameter of the molecular system model is the beat frequency directly related to the parameter characterizing the intramolecular interisomeric interactions (the corresponding nondiagonal element of the energy matrix) rather than the value of the nonradiative transition probability. The character of the change in the level populations and, accordingly, in the band intensities in the spectra in the proposed model is in good agreement with the experiment, including the fine structure of the time dependences — oscillations of the line intensities. In analyzing the temporal experiment with a high resolution, it is necessary to take into account the instrument function leading to quantitative and qualitative changes in the time dependences. The traditional model of nonradiative transitions with a constant probability value has a very limited range of applicability — very high beat frequencies compared to the probability of optical transitions.     

用改进嵌入原子法计算Cu晶体的表面能

用改进嵌入原子法(MEAM)计算了Cu晶体12个晶面的表面能.结果表明，密排面(111)的表面能最小.其他晶面的表面能随其晶面与(111)晶面夹角的增加而增加，据此可以粗略地估计各晶面表面能的相对大小.给出的几何结构因子的确定方法及结果可以直接用于计算其他面心立方晶体的表面能及其他特性.在Cu,Ag等面心立方薄膜中出现(111)择优取向或织构的机理是表面能的最小化. 关键词： 改进嵌入原子法 铜 表面能 计算     

Microstructure and high-temperature wear resistance of a laser surface alloyed γ-TiAl with carbon

TiC reinforced composite coating on γ-TiAl alloy was successfully fabricated by laser surface alloying with carbon. The fine TiC reinforcing phase had a gradient distribution in the coating, and its growth morphology of TiC in laser surface alloyed coating was in unique faceted platelet-like. The composite coating exhibited high hardness and excellent high-temperature sliding wear resistance.