球－盘微动摩擦件磨损体积的测量与计算

一般地说，由于微动磨损量很小，测定非常困难，所得结果的误差通常都相当大．尽管几十年来人们对微动磨损进行了好些研究，然而至今却还没有建立起统一而完善的微动磨损量的测量和计算方法，以至很难对试验结果进行定量比较．因此，根据ＳＲＶ微动磨损试验机的工作原理，利用几何和数学分析手段提出了一种能够比较精确地测量和计算球－盘接触型微动摩擦件磨损量的方法，并且利用不同的模型对计算方法进行简化，从而得出了球和盘的磨损体积计算公式。只要借助轮廓仪和读数显微镜测量出有关参数，就可以比较精确地计算出球和盘的微动磨损体积，为了验证这种计算方法的实用性和可靠性，还进行了５２１００钢对不同含钨量的Ｎｉ－Ｗ合金镀层的ＳＲＶ微动磨损试验，测量结果与计算结果具有较好的一致性，由此可见，根据所提计算方法得到的计算结果，不仅可以增强ＳＲＶ试验机测试结果的可比性，也为利用这种试验机深入开展微动磨损研究提供了参照依据。     

反射焦散线实验中斜入射光对应力强度因子测试精度的影响

本文用空间解析几何方法,推导了在一般非平行斜入射光条件下,裂纹体表面所形成的反射焦散线和初始曲线的方程.分析了倾斜入射光造成的焦散线畸变,给出了这种畸变造成的裂端应力强度因子测量误差的解析表达式.     

Direct interferometric measurement of streaming birefringence

The two refractive indices in the flow of a colloidal birefringent liquid are measured separately by means of a Mach-Zehnder interferometer. For a quantitative evaluation of the resulting interferograms it is not necessary to linearize the respective equations relating the refractive index distribution to the deformation velocity in the flow. Therefore it becomes possible to perform velocity measurements in the non-Newtonian flow range. An additional measurement of the mean flow rate enables one to determine the velocity field without the need of a calibration of the observed interference fringes.     

Reynolds stress, mean velocity, and dynamic static pressure measurement by a four-hole pressure probe

An improved version of the four-hole directional pressure probe, or Cobra probe, is described, in which the frequency response has been extended to 1.5 kHz. The probe measures all three orthogonal mean and turbulent velocity components at a point in the flow field. The probe also resolves the local mean and turbulent components of static pressure, allowing moments between the fluctuating velocity components and pressure to be determined. The techniques developed to allow the improved frequency response and the use of the probe in turbulent, developed pipe flow (a calibration flow) are described. Also given are the turbulent pressure-velocity correlations, which show a high degree of anticorrelation for one velocity component.     

Velocity profile measurement by ultrasonic doppler method

The ultrasonic velocity profile measuring method has been developed at PSI for application in fluid mechanics and fluid flow measurement. It uses pulsed ultrasonic echography together with the detection of the instantaneous Doppler shift frequency. This method has the following advantages over the conventional techniques: (1) an efficient flow mapping process, (2) applicability to opaque liquids, and (3) a record of the spatiotemporal velocity field. After a brief introduction of its principle, the characteristics and specifications of the present system are given. Then examples in fluid engineering for oscillating pipe flow, T-branching flow of mercury, and recirculating flow in a square cavity are described that confirm the method's advantages. Several other works under way by other investigators are introduced. A potential for in-depth study of fluid dynamics is demonstrated by several examples from an investigation of modulated wavy flows in a rotating Couette system. The position-averaged power spectrum and the time-averaged energy spectral density were used to study the dynamic characteristics of the flow, and subsequently the velocity field was decomposed into its intrinsic wave structure based on two-dimensional Fourier analysis.     

Motion of inviscid fluid tongues and bubbles in a Hele-Shaw cell occupied by a viscoelastic fluid

Problems of steady-state motion of an inviscid fluid tongue or bubble in a Hele-Shaw cell occupied by a viscoelastic fluid are considered. The problems generalize the well-known Saffman-Taylor problems [1, 2] in the approximation in which the pressure jump on the interface between the two fluids depends on the normal velocity of the interface [4]. In the zero approximation the results obtained by means of an iteration technique are in good agreement with the analytic solutions obtained by Saffman and Taylor [1, 2].__________Translated from Izvestiya Rossiiskoi Academii Nauk, Mekhanika Zhidkosti i Gaza, No. 1, 2005, pp. 117–123. Original Russian Text Copyright © 2005 by Entov, Kolganov, and Kolganova.     

Strain analysis for moiré interferometry using the two-dimensional continuous wavelet transform

In this paper, we introduce the two-dimensional continuous wavelet transform for the automated strain analysis of the moiré interference fringe pattern. The Fourier transform method has been widely used for automated analysis of an optical interference fringe pattern. However, this method is hardly applicable to the analysis of the fringe pattern, which includes large displacement range or discontinuities. We show the advantages of the wavelet transform method by applying it to experimental results on composite laminates.     

On the Validity of Darcy's Law for Stable High-Concentration Displacements in Granular Porous Media

Recently, it has been suggested that Darcy's Law might not be applicable for modelling miscible, density-dependent flow in porous media. To investigate this, three sets of careful laboratory column experiments were performed on coarse and medium sands, consisting of upward displacement of water by sodium chloride solutions with concentrations ranging from 5 to 200g/l. Data on salt concentrations and water pressures were collected in horizontal transects along the flow direction. Salt concentration data were also collected in the influent and exit lines. The experimental data were analysed using a simplified approach based on Darcy's Law alone, applied with the assumption of a sharp interface. Darcy's Law was used to estimate porous medium permeability by fitting predictions to experimental data. Consistent estimates of permeability were obtained for each set of experiments. The results indicate that Darcy's Law adequately describes high concentration displacements through saturated coarse- and medium-grained porous media.     

弱正交异性材料残余应力测量的声弹性方法

为了适应工程材料的残余应力无损测量的要求,本文将横波和纵波声弹性相结合,建立适用於弱正交异性材料的平面声弹性残余应力测量方法,并应用该方法及自行研制的横波换能器对焊接试件的二维残余应力进行了测试。