Influences of Sr2+ Doping on Microstructure,Giant Dielectric Behavior,and Non-Ohmic Properties of CaCu3Ti4O12/CaTiO3 Ceramic Composites

The microstructure, dielectric response, and nonlinear current-voltage properties of Sr²⁺-doped CaCu₃Ti₄O₁₂/CaTiO₃ (CCTO/CTO) ceramic composites, which were prepared by a solid-state reaction method using a single step from the starting nominal composition of CCTO/CTO/xSrO, were investigated. The CCTO and CTO phases were detected in the X-ray diffraction patterns. The lattice parameter increased with increasing Sr²⁺ doping concentration. The phase compositions of CCTO and CTO were confirmed by energy-dispersive X-ray spectroscopy with elemental mapping in the sintered ceramics. It can be confirmed that most of the Sr²⁺ ions substituted into the CTO phase, while some minor portion substituted into the CCTO phase. Furthermore, small segregation of Cu-rich was observed along the grain boundaries. The dielectric permittivity of the CCTO/CTO composite slightly decreased by doping with Sr²⁺, while the loss tangent was greatly reduced. Furthermore, the dielectric properties in a high-temperature range of the Sr²⁺-doped CCTO/CTO ceramic composites can be improved. Interestingly, the nonlinear electrical properties of the Sr²⁺-doped CCTO/CTO ceramic composites were significantly enhanced. The improved dielectric and nonlinear electrical properties of the Sr²⁺-doped CCTO/CTO ceramic composites were explained by the enhancement of the electrical properties of the internal interfaces.     

Effect of Polythiophene Content on Thermomechanical Properties of Electroconductive Composites

The thermal, mechanical and electrical properties of polymeric composites combined using polythiophene (PT) dopped by FeCl₃ and polyamide 6 (PA), in the aspect of conductive constructive elements for organic solar cells, depend on the molecular structure and morphology of materials as well as the method of preparing the species. This study was focused on disclosing the impact of the polythiophene content on properties of electrospun fibers. The elements for investigation were prepared using electrospinning applying two substrates. The study revealed the impact of the substrate on the conductive properties of composites. In this study composites exhibited good thermal stability, with T₅ values in the range of 230–268 °C that increased with increasing PT content. The prepared composites exhibited comparable PA T_g values, which indicates their suitability for processing. Instrumental analysis of polymers and composites was carried out using Fourier Transform Infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM).     

Fe(II) Spin Crossover/Polymer Hybrid Materials: Investigation of the SCO Behavior via Temperature-Dependent Raman Spectroscopy,Physicochemical Characterization and Migration Release Study

Polymeric composites constitute an appealing class of materials with applications in various fields. Spin crossover (SCO) coordination complexes are switchable materials with potential use in data storage and sensors. Their incorporation into polymers can be considered an effective method for their wider practical application. In this study, Fe(II) SCO/polylactic acid hybrid polymeric composites have been prepared by film casting. The mononuclear coordination complex [Fe{N(CN)₂}₂(abpt)₂] was incorporated into polylactic acid. The morphological, structural and thermoanalytical characterization of the composite films were performed via scanning electron microscopy (SEM), attenuated total reflectance (ATR/FTIR), Raman spectroscopy and differential scanning calorimetry (DSC). In addition, the migration release study (MRS) of the SCO compound from the polymeric matrix into the food simulant 50% v/v water/ethanol solution was also examined via UV/Vis absorption. Of particular interest was the investigation of the SCO behavior of the coordination complex after its incorporation into the polymer matrix; it was accomplished by temperature-dependent micro-Raman spectroscopy. The described attempt could be considered a preparatory step toward the development of SCO-based temperature sensors integrated into food packaging materials.     

Dielectric Spectroscopy Analysis of Liquid Crystals Recovered from End-of-Life Liquid Crystal Displays

In the present work, the dielectric properties of recycled liquid crystals (LCs) (non-purified, purified, and doped with diamond nanoparticles at 0.05, 0.1, and 0.2 wt%) were investigated. The studied LC mixtures were obtained from industrial recycling of end-of-life LC displays presenting mainly nematic phases. Dielectric measurements were carried out at room temperature on a frequency range from 0.1 to 10⁶ Hz using an impedance analyzer. The amplitude of the oscillating voltage was fixed at 1 V using cells with homogeneous and homeotropic alignments. Results show that the dielectric anisotropy of all purified samples presents positive values and decreases after the addition of diamond nanoparticles to the LC mixtures. DC conductivity values were obtained by applying the universal law of dielectric response proposed by Jonscher. In addition, conductivity of the doped LC mixtures is lower than that of the undoped and non-purified LC.     

太赫兹波段Smith-Purcell辐射的介质加载光栅高频特性

提出了一种用于Smith-Purcell效应器件的介质加载光栅慢波结构,通过研究该结构的注-波互作用过程,推导出带电子注的色散方程,并数值求解出波的线性增长率.利用色散方程,结合电磁场传播的边界条件,推导出Smith-Purcell效应振荡器工作所需的起振电流.详细研究了高频结构长度、电子注主要参数和介质相对介电常数对起振电流的影响,并与普通金属光栅结构进行了比较.结果表明:保持其他参数不变时,高频结构长度越短,起振电流越大;保持高频结构参数不变时,起振电流随电子注厚度和注-栅距离的增大而增大,随电子注电压的增大而减小;与金属光栅相比,介质的引入提高了注-波互作用的增长率,有效减小了振荡器的起振电流.理论计算结果与软件CHIPIC的模拟结果比较符合.     

Microstructure performance and formation mechanism of laser alloying rare earth oxides modified nanocrystalline layer on TA7

Nanoscale particles (NP) were observed in a Ni60–Ag–Si₃N₄–Y₂O₃ laser alloying (LA) layer on a TA7 titanium alloy, NP usually locate on the grain boundaries, which are able to block the motion of dislocation in a certain extent. Such layer mainly consisted of γ-Ni, TiN, γ-(Fe, Ni), TiAg and lots of amorphous phases. The wear resistance of such layer with laser scanning speed 3 mm/s was better than that of a LA layer with 6 mm/s, which was mainly ascribed to an uniform microstructure and less defect of layer. The high laser scanning speed made the existing time of laser molten pool be shorter than before, favoring the formation of a fine microstructure. However, the defects, such as pores were produced in LA layer (higher scanning speed), decreasing the wear resistance.     

Preparation of Low-dielectric Permittivity Polyimide Resins with High Surface Activity from Chemically Bonded Hyperbranched Polysiloxane

Thermosetting resin matrix is the key component of advanced wave-transparent composites,where low dielectric constant,excellent processability,high thermal stability,as well as good bonding ability are required for resins.Herein,we prepared a series of phenylethynyl terminated polyimide(PI)resins by grafting amine-functionalized hyperbranched polysiloxane(HBPSi)to PI chains during the in situ polymerization.The effects of HBPSi on the processability of oligomers,molecular packing,thermal stability,dielectric property and bonding ability to reinforce Kevlar fibers of the cured PI/HBPSi composite resins have been examined in detail.The dielectric constants of the cured composite resins were greatly reduced from 3.29 to 2.19 without compromising its processability and thermal stability.Meanwhile,the 10 wt％HBPSi-containing PI resin demonstrated better bonding ability to reinforce fibers with the interfacial shear strength(IFSS)of 37.64 MPa,compared with that of neat PI-6 matrix(27.34 MPa),and better adhesion to metal with the lap shear strength of 10.48 MPa,50％higher than that of neat resin PI-6(6.98 MPa).These resultant PI/HBPSi composite resins exhibit excellent comprehensive properties,indicating their great potential as low-dielectric constant resin matrix in radar radome.     

Reactive TiO2 Nanoparticles Compatibilized PLLA/PBSU Blends:Fully Biodegradable Polymer Composites with Improved Physical,Antibacterial and Degradable Properties

The fully biodegradable polymer blends remain challenges for the application due to their undesirable comprehensive performance.Herein,remarkable combination of superior mechanical performance,bacterial resistance,and controllable degradability is realized in the biodegradable poly(L-lactide)/poly(butylene succinate) (PLLA/PBSU) blends by stabilizing the epoxide group modified titanium dioxide nanoparticles (m-TiO2) at the PLLA-PBSU interface through reactive blending.The m-TiO2 can not only act as interfacial compatibilizer but also play the role of photodegradation catalyst:on the one hand,binary grafted nanoparticles were in situ formed and stabilized at the interface to enhance the compatibility between polymer phases.As a consequence,the mechanical properties of the blend,such as the elongation at break,notched impact strength and tensile yield strength,were simultaneously improved.On the other hand,antibacterial and photocatalytic degradation performance of the composite films was synergistically improved,it was found that the m-TiO2 incorporated PLLA/PBSU films exhibit more effective antibacterial activity than the neat PLLA/PBSU films.Moreover,the analysis of photodegradable properties revealed that that m-TiO2 nanoparticles could act as a photocatalyst to accelerate the photodegradation rate of polymers.This study paves a new strategy to fabricate advanced PLLA/PBSU blend materials with excellent mechanical performance,antibacterial and photocatalytic degradation performance,which enables the potential utilization of fully degradable polymers.     

Synergic Enhancement of High-density Polyethylene through Ultrahigh Molecular Weight Polyethylene and Multi-flow Vibration Injection Molding: A Facile Fabrication with Potential Industrial Prospects

General-purpose plastics with high strength and toughness have been in great demand for structural engineering applications. To achieve the reinforcement and broaden the application scope of high-density polyethylene(HDPE), multi-flow vibration injection molding(MFVIM) and ultrahigh molecular weight polyethylene(UHMWPE) are synergistically employed in this work. Herein, the MFVIM has better shear layer control ability and higher fabrication advantage for complex parts than other analogous novel injection molding technologies reported.The reinforcing effect of various filling times and UHMWPE contents as well as the corresponding microstructure evolution are investigated.When 5 wt% UHMWPE is added, MFVIM process with six flow times thickens the shear layer to the whole thickness. The tensile strength and modulus increase to 2.14 and 1.39 times, respectively, compared to neat HDPE on the premise of remaining 70% impact strength. Structural characterizations indicate that the enhancement is attributed to the improvement of shish-kebab content and lamellae compactness, as well as related to the corresponding size distributions of undissolved UHMWPE particles. This novel injection molding technology with great industrial prospects provides a facile and effective strategy to broaden the engineering applications of HDPE materials. Besides, excessive UHMWPE may impair the synergistic enhancement effect, which is also reasonably explained.     

Carbon Nanotube Reinforced Titanium Metal Matrix Composites Prepared by Powder Metallurgy—A Review

Titanium-based metal composites (TMCs) are showing great potential to replace existing traditional materials in aerospace, automotive, and other high temperature engineering applications. This is due to their excellent mechanical, thermal, and physical properties and improved strength to weight ratio. Weight savings in the aerospace industry results in higher efficiency. Carbon nanotubes (CNTs), because of their low density and high Young's modulus, are considered to be an excellent reinforcement for metal matrix composites (MMCs). In the last 20 years extensive research has been carried out to investigate the combination of carbon nanotubes with aluminum, nickel, copper, magnesium, and other metal matrices. The production techniques such as mechanical alloying through powder metallurgy routes and their effects on the mechanical properties of CNT reinforced TMCs are reviewed in this article. The role of the volume fraction of carbon nanotubes and their dispersion into the metal matrix are highlighted. Governing equations to predict the mechanical and tribological properties of CNT reinforced titanium matrix composites are deduced. With the help of this initial prediction of properties, the optimal processing parameters can be optimized. Successful development of CNT reinforced TMCs would result in better wear and mechanical behavior and enhance their ability to withstand high temperature and structural loading environments.