复合功能布的动态力学性能及本构关系

针对复合功能布的物理特性,利用材料试验机和分离式Hopkinson压杆装置,展开了准静态和动态条件下单层和双层复合功能布材料的单轴抗压实验,获得了两种材料在不同应变率下的应力应变曲线和材料的失效应力、应变.实验结果表明:复合功能布的动态失效强度明显高于准静态失效强度,而且随着应变率的增加其动态失效强度呈现增加的趋势,即该材料具有明显的应变率硬化效应.对应力应变曲线进行拟合,给出了材料的动静态粘弹性本构关系.并对复合功能布在不同应变率下的失效应变及材料的损伤结果进行了初步的分析.     

Analytical study of the interface in fibre-reinforced 2D composite material

Imperfect bonding between the constitutive components can greatly affect the properties of the composite structures.An asymptotic analysis of different types of imperfect interfaces arising in the problem of 2D fibrereinforced composite materials are proposed.The performed study is based on the asymptotic reduction of the governing biharmonic problem into two harmonic problems.All solutions are obtained in a closed analytical form.The obtained results can be used for the calculation of pull-out and pushout tests,as well as for the investigation of the fracture of composite materials.     

石墨包覆纳米镍颗粒的结构及磁性能的表征

在密闭容器中,用爆轰分解掺杂含有镍离子的混合炸药前驱体合成了核壳结构石墨包覆镍纳米颗 粒。调整混合炸药前驱体中碳源材料和金属源材料的有效摩尔比合成了球形、不同尺寸、核壳结构的磁性石 墨包覆纳米镍颗粒。采用X 射线衍射仪(XRD)、透射电镜(TEM)、能谱分析仪(EDX)和振动样品磁强计 (VSM)表征化学构成、结构形貌及磁性能。结果表明:颗粒大小主要分布在10~55nm 之间,复合纳米颗粒 主要由面心立方镍纳米晶体和石墨碳构成,常温下这些复合纳米颗粒主要表现出超顺磁性和铁磁性能。     

电沉积纳米晶Ni-Co-Fe-P合金镀层的组织结构与摩擦磨损性能

用脉冲电沉积方法制备了纳米晶N i-Co-Fe-P合金镀层.采用X射线衍射（XRD）,透射电镜（TEM）,扫描电镜（SEM）,能谱分析（EDS）等方法研究了合金镀层的微观组织结构和成份.采用显微硬度计和摩擦磨损试验机测试合金镀层的显微硬度和摩擦磨损性能.结果表明：纳米晶N i-40.41%Co-6.16%Fe-1.63%P合金镀层的晶粒尺寸为8.3 nm,显微硬度和耐磨性明显高于不含P的N i-Co-Fe镀层;适当温度退火可以提高镀层的硬度及耐磨性;镀层的耐磨性与其硬度成正相关,且随着硬度的提高,镀层的磨损机理由磨粒磨损和黏着磨损共同作用转变为磨粒磨损主导.     

复合材料周期结构数学均匀化方法的一种新型单胞边界条件

数学均匀化方法是计算周期复合材料结构的有效方法之一,单胞边界条件施加的合理性直接决定了影响函数控制方程的计算效率和精度,进而影响均匀化弹性参数和摄动位移的计算精度.本文首先将单胞影响函数作为虚拟位移处理,给出了单胞在结构中真实的边界条件,结果表明,四边固支适合作为二维结构单胞边界条件;其次,针对二维结构提出了超单胞周期边界条件,有效提高了影响函数的计算精度,并使用与虚拟位移相对应的虚拟势能泛函验证超单胞周期边界条件的有效性;最后,利用数值分析验证多尺度渐进展开方法的计算精度,强调了二阶摄动的必要性.     

Effect of the Nanotube Radius and the Volume Fraction on the Mechanical Properties of Carbon Nanotube-Reinforced Aluminum Metal Matrix Composites

By using the advantages of carbon nanotubes (CNTs), such as their excellent mechanical properties and low density, CNT-reinforced metal matrix composites (MMCs) are expected to overcome the limitations of conventional metal materials, i.e., their high density and low ductility. To understand the behavior of composite materials, it is necessary to observe the behavior at the molecular level and to understand the effect of various factors, such as the radius and content of CNTs. Therefore, in this study, the effect of the CNT radius and content on the mechanical properties of CNT-Al composites was observed using a series of molecular dynamics simulations, particularly focusing on MMCs with a high CNT content and large CNT diameter. The mechanical properties, such as the strength and stiffness, were increased with an increasing CNT radius. As the CNT content increased, the strength and stiffness increased; however, the fracture strain was not affected. The behavior of double-walled carbon nanotubes (DWNTs) and single-walled carbon nanotubes (SWNTs) was compared through the decomposition of the stress–strain curve and observations of the atomic stress field. The fracture strain increased significantly for SWNT-Al as the tensile force was applied in the axial direction of the armchair CNTs. In the case of DWNTs, an early failure was initiated at the inner CNTs. In addition, the change in the elastic modulus according to the CNT content was predicted using the modified rule of mixture. This study is expected to be useful for the design and development of high-performance MMCs reinforced by CNTs.     

Tunable Upconversion Emissions from Lanthanide-doped Monodisperse β-NaYF4 Nanoparticles

We report upconversion multicolor tuning based on uniform β-NaYF₄:Yb/Tm/Er nanoparticles. The as-synthesized nanoparticles with an average diameter of 25 nm are well dispersed in a wide range of nonpolar solvents including hexane, cyclohexane, dichloromethane, and toluene. These nanoparticles show intense upconversion emissions and the color output can be precisely modulated by adjusting activator ratios of Tm³⁺ to Er³⁺. Dopant-concentration dependent emission properties of the triply doped particle system are also investigated. In addition, we demonstrate that these nanoparticles can be readily transferred to polar solvents such as ethanol and water by growing a thin silica layer (10 nm) around the particles, providing potential applications in biological labeling and imaging.     

High-pressure and high-temperature generation using diamond/sic composite anvils prepared with hot isostatic pressing

Using a hot isostatic pressing (HIP) technique, we synthesized diamond/SiC composites from diamond and Si powders. At an HIP condition of 1450 °C and 100 MPa, a pressure much lower than that of the diamond stability field, diamond powders react with molten Si to form well-sintered diamond/SiC composites. Cubes of the composites with 15 mm edge length were thereby fabricated, and an application to the second stage anvils in a Kawai-type high-pressure apparatus was attempted. A hybrid anvils system using four cubes of the composites and four of the conventional WC was introduced and heating experiments up to 1600 °C became possible. Because the diamond/SiC composites are transparent to X-rays, the present system is applicable not only to diffraction studies but also to radiographic studies that need a larger window for an X-ray image.     

An internally heated composite gasket for diamond-anvil cells using the pressure-chamber wall as the heating element

The implementation of a heating element to a composite gasket for high-temperature applications in the diamond-anvil cell was developed based on a double-gasket assemblage. The heating element is a thin platinum wall that covers the central borehole of the metal–ceramic–metal composite gasket and interconnects the two metal component parts of the gasket. Applying electric powers up to 35 W to the two gasket metal components result in ring-like heating around the sample inside the pressure chamber with temperatures exceeding ～2000 K in individual cases. The ring-like distribution of the maximum temperature located at the pressure-chamber wall facilitates a homogeneous temperature distribution at the sample position. As a consequence of the concentration of the heating power to the pressure chamber region, gradients of surface temperatures, both at the gasket and the diamond anvil, appear to be more pronounced compared with those known for classical external electrical heating. Apart from the tests of the mechanical stability on high-pressure operation in the diamond anvil cell at room temperature, the influence of the anvils in contact with the gasket on the characteristic power–temperature curves, temperature gradients and thermal equilibration resulting from changes in electrical power settings have been evaluated within the scope of a series of experimental investigations.     

Banana fiber/chemically functionalized polypropylene composites with in-situ fiber/matrix interfacial adhesion by Palsule process

Chemically functionalized maleic anhydride (MAH)-grafted polypropylene matrix has been used (in place of polypropylene as matrix with compatibilizer) to process banana fiber/chemically functionalized polypropylene (BF/CFPP) composites, without using any compatibilizer and without any fiber modification by Palsule process. Fiber/matrix interfacial adhesion generated, in-situ, due to interactions between BF and the MAH of the CFPP matrix has been established by Fourier transform infrared spectroscopy and scanning electron microscopy. Mechanical properties of the BF/CFPP composites developed by Palsule process with in-situ fiber/matrix interfacial adhesion in this study have been found to be higher than those of the matrix and it increases with increasing amounts of fibers in composites, and are better than properties of literature reported BF/polypropylene composites processed with compatibilizers. Measured modulus of BF/CFPP composites compares well with values predicted by rule of mixtures, Hrisch model, Halpin-Tsai equations and its modified Nielsen version, and with Palsule equation. The feasibility of developing natural fiber/MAH grafted polyolefin composites by Palsule process without using any compatibilizer and without any fiber treatment is demonstrated.