Mm0.78Mg0.22Ni2.48Mn0.09Al0.23Co0.47储氢合金的表面改性

为了提高AB3型合金Mm_(0.78)Mg_(0.22)Ni_(2.48)Mn_(0.09)Al_(0.23)Co_(0.47)(Mm由82.3%La和17.7%Nd组成)的电化学性能,将石墨烯添加到合金中。通过XRD和SEM可以看出,石墨烯并没有改变合金的相结构,仅是简单地附在合金表面。当加入质量分数为2%的石墨烯时,合金电极的最大放电容量Cmax达到364.9 m Ah·g-1。石墨烯的添加加速了合金表面的电化学反应。     

铝掺杂表面分子印迹聚合物修饰电极检测食品中罗硝唑残留

以罗硝唑(Ronidazole,RNZ)为模板,3-氨丙基三乙氧基硅烷为功能单体,Al(Ⅲ)为路易斯酸掺杂剂,用溶胶-凝胶法制备核壳型磁性分子印迹聚合物,借助磁力作用将其修饰于磁性玻碳电极表面,制得RNZ电化学印迹传感器。以透射电镜、红外光谱、X-射线衍射及电化学方法等对该传感器进行表征,并对影响传感器性能的主要参数进行优化。结果表明,相比基于非掺杂印迹聚合物和非分子印迹聚合物的传感器,铝掺杂印迹传感器对罗硝唑具有更强的结合能力和更高的识别选择性。用差分脉冲溶出伏安法进行定量测定时,RNZ的还原峰电流与其浓度在0.05~50.0μmol/L范围内呈良好线性关系(r=0.997 3),检出限为0.015μmol/L。对牛奶、鸡蛋中RNZ的回收率为88.6%~97.0%,相对标准偏差(RSD)为2.9%~4.6%。     

Solid Amine Adsorbent Prepared by Molecular Imprinting and Its Carbon Dioxide Adsorption Properties

A carbon dioxide imprinted solid amine adsorbent (IPEIA‐R) with polyethylenimine (PEI) as a skeleton was conveniently prepared by using glutaraldehyde to cross‐link carbon dioxide‐preadsorbed PEI. As confirmed by FTIR, FT‐Raman, and ¹³C NMR spectroscopy, CO₂ preadsorbed on PEI could occupy the reactive sites of amino groups and act as a template for imprinting in the cross‐linking process. The imino groups formed from the cross‐linking reaction between glutaraldehyde and PEI could be reduced by NaBH₄ to form CO₂‐adsorbable amino groups. The adsorption results indicated that CO₂ imprinting and reduction of imino groups by NaBH₄ endowed the adsorbent with a higher CO₂ adsorption capacity. Compared with PEI‐supported mesoporous adsorbents, the solid amine adsorbent with PEI as a skeleton can avoid serious pore blockage and CO₂ diffusion resistance, even with a high amine content. The solid amine adsorbent with PEI as a skeleton showed a remarkable CO₂ adsorption capacity (8.56 mmol g^?1) in the presence of water at 25 °C, owing to the high amine content and good swelling properties. It also showed promising regeneration performance and could maintain almost the same CO₂ adsorption capacity after 15 adsorption–desorption cycles.     

Toll-like receptors for pathogen detection in water: challenges and benefits

The need for effective and efficient methods for pathogen detection in water is as serious as ever due to the health risk posed to human population by the consumption of pathogen-contaminated water. One of the important research streams which have been focused on by researchers for development of novel techniques for this purpose is biosensor technologies. Using different bio-recognition elements and transduction methodologies, biosensors have the potential to detect their analyte of interest in a fast and highly specific manner. Different pathogenic agents can be recognised by toll-like receptors (TLRs). The innate immune system of higher organisms employs TLRs for triggering intracellular signalling and induction of the expression of immune response genes. In this report, we explore the challenges associated with employing TLRs for pathogen detection in water samples. Although methods using TLR expressing cells also have been discussed, the focus of this review is on using TLR proteins as the bio-recognition elements in biosensors.     

表面键联型TiO2/SiO2固定化催化剂的结构及催化性能

 采用浸渍法制备了表面键联型TiO2／SiO2固定化光催化剂．XRD\r\n,FT－IR,XPS和BET比表面积测定结果表明,TiO2通过Ti－O－Si联结\r\n负载于多孔硅胶的表面,由此提出TiO2／SiO2的结构模型．考察了多孔\r\n硅胶的粒度及氧化钛负载量对催化剂活性的影响．对活性艳红K－2G（\r\nR15）的光催化脱色反应,最佳的光催化剂30％TiO2／SiO2（Ims30）比\r\nB－TiO2粉末的催化速率快3倍．随着载体粒度的减小,催化剂的比表面\r\n积增大,催化活性升高;多孔硅胶不仅起着支持体的作用,而且具有分\r\n散的作用;多孔硅胶具有很好的透光性．经ξ－电位测定,所制备催化\r\n剂的等电点为3．0pH单位,表明催化剂表面呈酸性．     

CO在Sm/Rh(100)模型表面上的吸附与反应

应用AES,LEED,XPS和TDS研究了Rh(100)上Sm膜和Sm/Rh表面合金以及CO在这两类模型表面的吸附与反应.室温下Sm在Rh(100)上的生长遵从SK模式,Sm膜经900K高温退火后可形成有序表面合金.在室温制备的Sm膜/Rh(100)表面上,室温下CO在Sm上的吸附改变了表面结构,生成SmOx和表面碳.随着Sm覆盖度的增加,低温脱附峰(α-CO)面积迅速下降,且峰温向高温方向位移;表明Sm的空间位阻和电子效应同时起作用.在Sm/Rh合金表面上,CO在约590K出现新的脱附峰,可归属为受Sm电正性修饰的Rh原子上的CO脱附峰     

Surface properties of silica gel samples modified by selected proteins

The adsorption of a polar (water) and a non-polar (n-octane) liquid on silica gels, modified by adsorption of proteins, has been studied by thermal analysis. Silica gels with physically adsorbed BSA and ovalbumin layers were used. Thermodesorption energies were determined from Q-TG and Q-DTG curves recorded under quasi-equilibrium conditions. Significant differences in liquid desorption were observed from the surfaces due to heterogeneous changes (energetic and geometrical) as a result of modification. These results are compared with those obtained for the samples heated at 160°C for 1 h.     

反离子对离子液体氯化1-(2-羟乙基)-3-十二烷基咪唑在水溶液中自组装的影响

用表面张力法和荧光探针技术分别测定了阳离子型离子液体表面活性剂氯化1-(2-羟乙基)-3-十二烷基咪唑([C2OHC12im]Cl)在无机盐(NaX,X=Cl-,Br-,I-和Na2SO4)水溶液中的自组装参数。 结果表明,反离子通过结合[C2OHC12im]+并中和其表面电荷,使[C2OHC12im]+的临界胶束浓度(CMC)和胶束平均聚集数(Nm)等自组装参数明显改变;改变幅度按照Cl-＜Br-＜I-＜SO2-4次序递增;但是反离子(Cl-、Br-和SO2-4)种类对临界胶束平均聚集数(Nm,c)和胶束微极性([I1/I3]m)的影响不甚明显;随着Br-浓度增加,lg CMC线性减小,而Nm则以幂函数形式递增。     

硬脂酸/异氰酸酯摩尔比对聚丙烯/木粉复合材料性能的影响

用甲苯-2,4-二异氰酸酯（TDI）和硬脂酸（SA）复合改性木粉,在双螺杆挤出机中制备了聚丙烯（PP）基的木塑复合材料（WPC）,研究了SA/TDI摩尔比对木粉表面性能、复合材料力学性能和加工性能的影响。 结果表明,随着SA/TDI摩尔比的增大,改性木粉的表面张力逐渐减小,与PP的界面张力先减小后增大;与未改性的WPC相比,SA/TDI复合改性剂对WPC的拉伸强度、弯曲强度、缺口冲击强度影响不明显,但对无缺口冲击强度提升较大;当SA/TDI摩尔比为1.07时,复合材料的无缺口冲击强度和熔体质量流动速率分别达到9.74 kJ/m2和13.12 g/10 min,分别比未改性WPC提高了77%和22%。