D→Klv～l衰变过程的研究

用光锥QCD求和规则研究D→Klv～_l衰变过程，首先计算D→K跃迁形状因子，通过构造新的关联函数，消除了twist-3波函数的不确定性给计算结果所带来的影响，从而使计算结果更加精确. 计算得到的分支比与最近的实验数据相一致. 关键词： QCD光锥求和规则 D介子半轻衰变 分支比 形状因子     

Fabrication of isotype (p-p) selenium-polyaniline heterojunction diode by electrochemical method

In the present work, for the first time, heterojunction has been fabricated using electrochemically deposited isotype p-selenium-p-polyaniline from a single solution bath. The structural characterization of selenium and polyaniline thin film was carried out using XRD technique. Polyaniline exhibited amorphous structure while selenium offered monoclinic (β) phase. The junction was formed by electrodepositing polyaniline over selenium film and heating at 423 K. The current density versus voltage (J-V) plot showed the formation of a junction with ideality factor of 1.16. From J-V characteristics at different temperatures, static resistance (R_s), dynamic resistance (R_d), and rectification ratio of diodes were determined. Heat treatment above 448 K caused junction breakdown.     

Electrical properties of polypyrrole/p‐InP structure

The polypyrrole/p‐InP structure has been fabricated by the electrochemical polymerization of the organic polypyrrole onto the p‐InP substrate. The current–voltage (I–V), capacitance–voltage (C–V), and capacitance–frequency (C–f) characteristics of the PPy/p‐InP structure have been determined at room temperature. The structure showed nonideal I–V behavior with the ideality factor and the barrier height 1.48 and 0.69 eV respectively. C–f measurements of the structure have been carried out using the Schottky capacitance spectroscopy technique and it has been seen that there is a good agreement between the experimental and theoretical values. Also, it has been seen that capacitance almost show a plateau up to a certain value of frequency, after which, the capacitance decreases. The higher values of capacitance at low frequencies were attributed to the excess capacitance resulting from the interface states in equilibrium with the p‐InP that can follow the a.c. signal. The interface state density N_ss and relaxation time τ of the structure were determined from C–f characteristics. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1572–1579, 2006     

利用低能质子束产生高强度放射性束流

加拿大TRIUMF实验室利用¹¹C成功验证了一种产生高强度(～10⁸ions/s)放射性束流的方法. 该方法不同于普通在线同位素分离方法, 它利用了13MeV的低能强流质子束, 可以产生一系列核天体物理实验感兴趣的高强度放射性束流.     

Study of fiber optic sugar sensor

Over the last two decades, the fiber optic technology has passed through many analytical stages. Some commercially available fiber optic sensors, though in a small way, are being used for automation in mechanical and industrial environments. They are also used for instrumentation and controls. In the present work, an intensity-modulated intrinsic fiber optic sugar sensor is presented. This type of sensor, with slight modification, can be used for on-line determination of the concentration of sugar content in sugarcane juice in sugar industry. In the present set-up, a plastic fiber made of polymethylmethacrylate is used. A portion of the cladding (1 cm, 2 cm, 3 cm) at the mid-point along the length of the fiber is removed. This portion is immersed in sugar solution of known concentration and refractive index. At one end of the fiber an 850 nm source is used and at the other end a power meter is connected. By varying the concentration of sugar solution, the output power is noted. These studies are made due to the change in refractive index of the fluid. The device was found to be very sensitive which is free from EMI and shock hazards, stable and repeatable and they can be remotely interfaced with a computer to give on-line measurements and thus become useful for application in sugar industries.     

Gas transport through homogeneous and asymmetric polyethersulfone membranes

Both homogeneous and asymmetric polyethersulfone (PES) membranes were prepared by solvent casting. The sorption and permeation behavior of CO₂, O₂, and N₂ using these two kinds of cast PES membranes and commercially available homogeneous PES film was investigated to extract the pressure dependence of gas permeability and the permselectivity for CO₂ relative to N₂, and to confirm the validity of the working assumption that a skin layer in an asymmetric membrane can be essentially replaced by a thick homogeneous dense membrane. The pressure dependence of the mean permeability coefficient to CO₂ in homogeneous membranes obeys the dual-mode mobility model. The ideal separation factor for CO₂ relative to N₂ at an upstream pressure of 0.5 MPa attains ca. 40, while the permeability to CO₂ is about 2.7 Barrer at the same upstream pressure. The same separation factor in asymmetric membranes amounts to 35. The diffusion behavior for the skin layer in an asymmetric membrane with a thin skin layer can be simulated approximately by that in a homogeneous dense membrane. © 1993 John Wiley & Sons, Inc.     

1．5GHz锯材超导腔的研制

介绍铌材超导腔的研制进展，重点讨论了国产铌腔的材料改性，以及相应的超导腔性能的改进．叙述了１．５ＧＨｚ铌腔的腔形设计，分析了铌材的射频性能和机械性能，制定了铌腔制作与后处理的特定工艺．最后给出了１．５ＧＨｚ铌材超导腔的低温实验结果．     

Functional Central Limit Theorems for Triangular Arrays of Function-Indexed Processes under Uniformly Integrable Entropy Conditions

Functional central limit theorems for triangular arrays of rowwise independent stochastic processes are established by a method replacing tail probabilities by expectations throughout. The main tool is a maximal inequality based on a preliminary version proved by P. Gaenssler and Th. Schlumprecht. Its essential refinement used here is achieved by an additional inequality due to M. Ledoux and M. Talagrand. The entropy condition emerging in our theorems was introduced by K. S. Alexander, whose functional central limit theorem for so-calledmeasure-like processeswill be also regained. Applications concern, in particular, so-calledrandom measure processeswhich include function-indexed empirical processes and partial-sum processes (with random or fixed locations). In this context, we obtain generalizations of results due to K. S. Alexander, M. A. Arcones, P. Gaenssler, and K. Ziegler. Further examples include nonparametric regression and intensity estimation for spatial Poisson processes.     

An evolutionary method for optimization of plate buckling resistance

Optimization of plate buckling resistance is very complicated, because the in-plane stress resultants in the prebuckled state of a plate are functions of thickness distribution. This paper discusses the problem of finding the optimum thickness distribution of isotropic plate structures, with a given volume and layout, that would maximise the buckling load. A simple numerical method using the finite-element analysis is presented to obtain the optimum thickness distribution. Optimum designs of compression-loaded rectangular plates with different boundary conditions and plate aspect ratios are obtained by using the proposed method. Optimum designs from earlier studies and the methods of buckling analysis used to attain these results are discussed and compared with the designs from the proposed method. This paper also examines the reliability of the optimality criterion generally used for plate buckling optimization, which is based on the uniform strain energy density.     

A Monte Carlo method for an objective Bayesian procedure

This paper describes a method for an objective selection of the optimal prior distribution, or for adjusting its hyper-parameter, among the competing priors for a variety of Bayesian models. In order to implement this method, the integration of very high dimensional functions is required to get the normalizing constants of the posterior and even of the prior distribution. The logarithm of the high dimensional integral is reduced to the one-dimensional integration of a cerain function with respect to the scalar parameter over the range of the unit interval. Having decided the prior, the Bayes estimate or the posterior mean is used mainly here in addition to the posterior mode. All of these are based on the simulation of Gibbs distributions such as Metropolis' Monte Carlo algorithm. The improvement of the integration's accuracy is substantial in comparison with the conventional crude Monte Carlo integration. In the present method, we have essentially no practical restrictions in modeling the prior and the likelihood. Illustrative artificial data of the lattice system are given to show the practicability of the present procedure.