多芯NbTi/Cu复合棒的制造工艺改进和完善

本文是对传统制造工艺改进和完善,制造多芯NbTi/Cu复合棒研究实验.通过自设计制作一套组装工装成功两次组装8000芯NbTi/Cu复合大包套(φ220 mm×560 mm);利用非真空焊封工艺成功焊封多芯大包套;在挤压拉伸过程中增加了热等静压和扒皮工艺,提高了铜材洁净度及复合包套的填充系数;分析挤压过程中芯棒的变形行为规律:当包套填充系数＞93%时,挤压芯棒排列紧密,均匀变形;填充系数＜93%时,挤压芯棒出现不规则变形.     

Dynamics analysis of slender vehicle influenced by random factors

In this paper, the aeroelastic problems of slender vehicles under the influence of random factors and thrust are studied. An aeroelastic dynamic model of a free-free Euler–Bernoulli beam considering thrust and aerodynamic forces is established based on Hamilton’s principle of nonconservative systems. On this basis, considering the influence of random factors, the elastic modulus and viscous drag are regarded as one-dimensional continuous stationary random fields and discretized. The stochastic finite element method is used to solve the dynamic model, and the results are compared with the Monte Carlo simulation results. Then, the influence of the correlation of the random field on the elastic displacement is further analyzed. The following simulation results are obtained: (1) the stochastic factor analysis model established in this paper can reflect the statistical characteristics of aeroelastic response well; (2) the stronger the correlation of the random field is, the greater the expectation of elastic displacement, but as the correlation increases, the expectation tends to be constant; and (3) it is necessary to choose the discrete length of the random field reasonably, and the discrete length depends on the correlation characteristics of the random field studied.     

高亮度半导体激光阵列光纤耦合模块

利用2只915 nm半导体激光短列阵作为子模块,设计并研制出连续输出的高亮度光纤耦合模块。首先对每个半导体激光短列阵进行光束整形,从而提高它的光束质量;然后采用空间复用技术将这两个半导体激光短列阵出射的激光在光参数积小的方向上叠加,并利用偏振复用技术进一步提高光束质量;最后利用单片非球面透镜将激光聚焦到芯径为100 μm、数值孔径为0.22的光纤中。测量结果显示:在工作电流为52.5 A时,聚焦镜焦平面的光斑尺寸为105.4 μm;耦合后测量光纤出光功率可达72.6 W,对应亮度为6.08 MW/(cm²·sr),模块的电光转换效率为42.2%。最后测量了模块在不同驱动电流时的光谱,证明该模块的散热性能良好。     

Bending of Bars under a Follower Load

Exact solutions of the problem of nonlinear bending of a thin bar under a point follower load are given. The problem is studied for an arbitrary follower angle and the particular cases of axial and transverse follower forces are considered. The solutions are written in unified parametric form and expressed in terms of Jacobi elliptic functions.     

Contribution to 3D impact problems: collisions between two slender steel barsUne contribution aux problèmes d'impact en trois dimensions : collisions entre deux barres élancées

This Note deals with the three-dimensional phenomenon of collision between two slender steel bars. The problem posed is whether the restitution concept developed in rigid-body theory is relevant in the case of such slender contactors. Some elements of an answer are provided through the use of two complementary approaches of collision, a theoretical one based on coefficients of restitution and series of experiments. Our main conclusion is that the alleged Newton coefficient of restitution varies according to the impact location on the rods. To cite this article: C. Le Saux et al., C. R. Mecanique 332 (2004).     

Selective Solid‐phase Extraction of Bisphenol A Using a Novel Stir Bar Based on Molecularly Imprinted Monolithic Material

In this paper, a novel monolithic stir bar based on molecularly imprinted polymer (MIP) was firstly developed by filling modified neodymium magnet (Nd₂Fe₁₄B) powders into a glass tube (60 × 4 mm), followed by the imprinted grafting with bisphenol A (BPA) as the template molecule by thermal polymerization. It has been successfully used for the stir bar sorptive extraction (SBSE) and its extraction performance illustrated that the MIP‐encapsulated stir bar had stronger affinity to the template molecule, compared with the stir bar based on the non‐imprinted molecularly polymer (NIP). Under the optimal extraction conditions, a simple method based on the coupling of MIP‐SBSE with high performance liquid chromatography (HPLC) was used for the selective determination of the model mixtures of BPA, 4‐phenylphenol (PP) and phenol (P) in bottled water. The recoveries of BPA, PP and P were in the range of 88.5‐96.1%, 78.2‐89.7%, 81.3‐89.5% at three spiked levels, respectively, demonstrating that higher extraction and the specific absorption occurred between the template molecule and the prepared MIP stir bar.     

Nanoscale Magnetic Stirring Bars for Heterogeneous Catalysis in Microscopic Systems

Nanometer‐sized magnetic stirring bars containing Pd nanoparticles (denoted as Fe₃O₄‐NC‐PZS‐Pd) for heterogeneous catalysis in microscopic system were prepared through a facile two‐step process. In the hydrogenation of styrene, Fe₃O₄‐NC‐PZS‐Pd showed an activity similar to that of the commercial Pd/C catalyst, but much better stability. In microscopic catalytic systems, Fe₃O₄‐NC‐PZS‐Pd can effectively stir the reaction solution within microdrops to accelerate mass transfer, and displays far better catalytic activity than the commercial Pd/C for the hydrogenation of methylene blue in an array of microdroplets. These results suggested that the Fe₃O₄‐NC‐PZS‐Pd could be used as nanoscale stirring bars in nanoreactors.     

双杠三维测力系统的研制及应用

双柑三维测力系统由三维测力传感器、动态电阻应变仪，７Ｔ１７Ｓ数字信号处理机组成，可提供各种实时处理的测量数据及图形。经运动员实际测试，取得了比较满意的结果，可用于双杠运动员的实际训练中。     

Recent progress on the study of asymmetric vortex flow over slender bodies

The investigations of forebody vortex flow and its flow control have great importance in both academic field and engineering application areas. A large number of papers and many review papers have been published. However in this research field of forebody asymmetric vortices, three problems such as tip perturbation effect, Reynolds number effect and flow instability are less studied and thus not understood completely. So many researches are still working on the issues in recent years. The present paper attempts to provide a review of recent research progress on first two problems. The first problem is mainly concerned with how the vortex flow evolves after tip perturbation; how to solve the problem of repeatability and reproducibility of wind tunnel testing data; how to develop a conception of active flow control technique with tip perturbation based on the study of vortex flow response to tip perturbation. For the second problem one is mainly concerned that how the asymmetric vortices are developed with the increase of Reynolds number; how to classify the vortex flow patterns in different Reynolds number regimes; how to develop an appropriate boundary layer transition technique to simulate flows at high Reynolds number in the convention wind tunnels. Finally, some important ques- tions that deserve answers are proposed in the concluding remarks.     

A New Testing Method to Investigate the Compacting Behaviour of Fresh Concretes Under Impact Loading

This paper presents a new instrumented Proctor test using a Hopkinson bar which allows for the original measurement of forces and velocities during the impact loading on soft fresh concrete samples. For this purpose, the specific points of using low impedance Nylon bar as well as the two-point measurement method to recover coupled waves are discussed. The whole test consists of successive impacts of low velocity (less than 3 m/s) exerted on the compressible specimen of a fresh concrete. The proposed original measurement allows for a quantitative comparison of the behaviour of the fresh concrete submitted to quasi-static and impact compaction. It shows that impact compaction is more efficient than quasi-static case. However, the increase of the impact velocity seems to reduce the efficiency. There exists probably an optimal loading path. The further understanding of the behaviour of fresh concrete under low velocity impact should be an interesting way to improve the industrial compacting process.