The effect of a transition layer between a fluid and a porous medium: shear flow in a channel

Flow in a three-layer channel is modeled analytically. The channel consists of a transition layer sandwiched between a porous medium and a fluid clear of solid material. Within the transition layer, the reciprocal of the permeability varies linearly across the channel. The Brinkman model is used for the momentum equations for the porous medium layer and the transition layer. The velocity profile is obtained in closed form in terms of Airy, exponential, and polynomial functions. The overall volume flux and boundary friction factors are calculated and compared with values obtained with a two-layer model employing the Beavers–Joseph condition at the interface between a Darcy porous medium and a clear fluid.     

贵州石漠化地区降雨条件下红粘土剪切强度特性随含水量变化关系探讨

西南喀斯特地区的石漠化已经严重影响了人民正常的生产生活。水土流失是石漠化过程中一个关键环节。喀斯特地区地表广泛覆盖的红粘土在降雨条件下随着含水量的增加和人工垦殖的影响,剪切强度会产生变化,更易发生水土流失。本文以贵州普定石漠化研究区（陈旗村）的红粘土为例,以原状土模拟未经扰动的土样,以重塑土来模拟经过开垦被扰动后的土样,设计了原状土和重塑土在不同含水量下的直剪试验,初步地研究了这一变化规律。结果表明:在含水量大于35%时,石漠化地区红粘土粘聚力和内摩擦角均随着含水量的增加显著降低;在同一含水量水平下,原状土的抗剪强度明显优于重塑土,且随着含水量的增加,重塑土的强度衰减较之原状土快许多,表明了经过人工垦殖后的红粘土在降雨条件下更易发生水土流失。       

反分析法与室内试验法确定岩质边坡结构面抗剪强度对比研究——以西柏坡纪念馆不稳定斜坡为例

岩质边坡结构面抗剪强度是分析边坡稳定性的重要参数。反分析法是视滑坡将要滑动而尚未滑动的瞬间为极限平衡状态,求解滑动面抗剪强度的一种方法,相对于室内实验和原位测试具有成本低的特点,但其普适性较差,对反分析法的应用条件进行研究对该方法在边坡工程中的准确应用具有重要意义。本文用反分析和室内试验两种方法确定西柏坡纪念馆不稳定斜坡结构面抗剪强度,发现对于单滑动面岩质顺层滑坡,直接采用滑坡断面进行反分析获得的结构面抗剪强度与室内试验结果相近,可用于评价同一结构面边坡的稳定性。     

Large Deformation of Nitinol Under Shear Dominant Loading

Full-field quantitative strain maps of phase transformation and plasticity in Nitinol under large shear-dominated deformation are presented. To achieve a shear-dominated deformation mode with relatively uniform stresses and strains, a shear compression specimen (SCS) geometry was utilized. Shear deformation appears to impede the development of the strain localization during phase transformation that is seen in uniaxial testing. The shear-dominant deformation of Nitinol in the plastic regime exhibits low hardening and results in the development of significant strain inhomogeneity.     

Strain localisation patterns under equal-channel angular pressing

Instabilities of plastic flow in the form of localised shear bands were experimentally observed to result from equal-channel angular pressing (ECAP) of magnesium alloy AZ31. The appearance of shear bands and their spacing were dependent on velocity of the pressing and applied back-pressure. A generic gradient plasticity theory involving second-order strain gradient terms in a constitutive model was applied to the case of AZ31 deformed by ECAP. Linear stability analysis was applied to the set of equations describing the deformation behaviour in the process zone idealised as a planar shear zone. A full analytical solution providing a dispersion relation between the rate of growth of a perturbation and the wave number was obtained. It was shown that the pattern of incipient localised shear bands exhibits a spectrum of characteristic lengths corresponding to admissible wave numbers. The interval of the spectrum of wave numbers of viable, i.e. growing, perturbations predicted by linear stability analysis was shown to be in good agreement with the experimentally observed spectrum. The effect of back-pressure applied during ECAP was also considered. The predicted displacement of the shear band spectrum towards lower wave numbers, shown to be a result of the decreased shear strain rate in the shear zone, was consistent with the experimentally observed increase of the band spacing with increased back-pressure. A good predictive capability of the general modelling frame used in conjunction with linear stability analysis was thus demonstrated in the instance of the particular alloy system and the specific processing conditions considered.     

Turbulent statistical characteristics associated to the north wind phenomenon in southern Brazil with application to turbulent diffusion

A parameterization for the transport processes in a shear driven planetary boundary layer (PBL) has been established employing turbulent statistical quantities measured during the north wind phenomenon in southern Brazil. Therefore, observed one-dimensional turbulent energy spectra are compared with a spectral model based on the Kolmogorov arguments. The good agreement obtained from this comparison leads to well defined formulations for the turbulent velocity variance, local decorrelation time scale and eddy diffusivity. Furthermore, for vertical regions in which the wind shear forcing is relevant, the eddy diffusivity derived from the north wind data presents a similar profile to those obtained from the non-extensive statistical mechanics theory. Finally, a validation for the present parameterization has been accomplished, using a Lagrangian stochastic dispersion model. The Prairie Grass data set, which presents high mean wind speed, is simulated. The analysis developed in this study shows that the turbulence parameterization constructed from wind data for north wind flow cases is able to describe the diffusion in a high wind speed, shear-dominated PBL.     

Radiating gravitational collapse with shear viscosity revisited

A new model is proposed to a collapsing radiating star consisting of an isotropic fluid with shear viscosity undergoing radial heat flow with outgoing radiation. In a previous paper we have introduced a function time dependent into the g _rr , besides the time dependent metric functions and . The aim of this work is to generalize this previous model by introducing shear viscosity and compare it to the non-viscous collapse. The behavior of the density, pressure, mass, luminosity and the effective adiabatic index is analyzed. Our work is compared to the case of a collapsing shearing fluid of a previous model, for a star with 6 . The pressure of the star, at the beginning of the collapse, is isotropic but due to the presence of the shear the pressure becomes more and more anisotropic. The black hole is never formed because the apparent horizon formation condition is never satisfied. An observer at infinity sees a radial point source radiating exponentially until reaches the time of maximum luminosity and suddenly the star turns off. The effective adiabatic index has a very unusual behavior because we have a non-adiabatic regime in the fluid due to the heat flow.     

Relations between a micro-mechanical model and a damage model for ductile failure in shear

Gurson type constitutive models that account for void growth to coalescence are not able to describe ductile fracture in simple shear, where there is no hydrostatic tension in the material. But recent micro-mechanical studies have shown that in shear the voids are flattened out to micro-cracks, which rotate and elongate until interaction with neighbouring micro-cracks gives coalescence. Thus, the failure mechanism is very different from that under tensile loading. Also, the Gurson model has recently been extended to describe failure in shear, by adding a damage term to the expression for the growth of the void volume fraction, and it has been shown that this extended model can represent experimental observations. Here, numerical studies are carried out to compare predictions of the shear-extended Gurson model with the shear failures predicted by the micro-mechanical cell model. Both models show a strong dependence on the level of hydrostatic tension. Even though the reason for this pressure dependence is different in the two models, as the shear-extended Gurson model does not describe voids flattening out and the associated failure mechanism by micro-cracks interacting with neighbouring micro-cracks, it is shown that the trends of the predictions are in good agreement.     

剪切波对HIFU经颅聚焦形成温度场影响的数值仿真研究

在高强度聚焦超声经颅治疗时,既有纵波又有剪切波,为了保障该治疗方法的安全有效性,有必要分析剪切波对HIFU治疗温度场的影响。该文基于人体头颅CT数据和曲率半径为150 mm的256阵元的半球相控换能器建立三维高强度聚焦超声经颅声波传播模型,利用时域有限差分法结合Westervelt声波非线性传播方程、动量方程、质量守恒方程和Pennes生物热传导方程数值仿真其形成温度场,研究在相同输入功率、不同聚焦角度条件下对应阵元数进行激励时,剪切波对换能器形成温度场的影响。结果表明,随换能器聚焦角度减小,在几何焦点处形成的焦域面积逐渐增大,考虑剪切波形成的温度场达到65?C所需时间逐渐延长,焦点前移程度越大;在相同聚焦角度条件下,考虑剪切波的温度场达到65?C所需时间更短,旁瓣更少,在颅骨处的温度更高,对焦点前移几乎没有影响;随换能器聚焦角度减小,考虑剪切波的模型形成的焦域面积变化范围更大;幂指数函数形式对不同聚焦角度下焦域面积大小的拟合优度高,可预测不同聚焦角度换能器形成的焦域面积。     

Shear Layer Dynamics in a Reacting Jet in Crossflow

This study explores the effect of heat release on the growth of the shear layer vortical structures in a reacting jet in crossflow. Jets composed of mixtures of hydrogen, helium and nitrogen were used to independently vary the momentum flux ratio (J), jet to crossflow density ratio (S) and heat release. Velocity fields were obtained from 10?kHz high-speed stereoscopic particle image velocimetry (SPIV) and regions of elevated temperature/combustion products from simultaneous OH planar laser induced fluorescence (OH-PLIF). The shear layer vortices (SLV) originating from instabilities in the windward and leeward shear layers were identified using vortex identification indicator functions in order to track their spatial location and strength. The results show that the asymmetries in shear layer strength between the windward and leeward shear layers are dependent primarily on J, for both reacting and non-reacting flow-fields. The SLV growth rate dependencies on J and S is found to match trends noted by previous studies for non-reacting jets, where SLV growth rates increase with degree of global instability of the JICF. Heat release is also shown to suppress the SLV growth rates relative to non-reacting cases with the same jet parameters. Related to this point, the degree of lifting of the flame also has a significant impact on SLV growth. As flame lifting is directly related to autoignition times, this point shows strong coupling between kinetic rates and jet hydrodynamic stability.