Effects of boundary conditions and anisotropy on elastically bent silicon

In four-point bending, the rollers that are used for load application impose additional constraints on the specimen that affect the anticlastic specimen curvature and cause the specimen displacement and stress profiles to deviate from the pure beam bending case. In this study, x-ray microdiffraction is used to map both the principal and anticlastic curvatures of elastically bent, rectangular (100)-type Si strips possessing width:thickness ratios of 40:1. We quantify the amount of roller constraint and show that the region over which the anticlastic specimen curvature is affected away from the roller is approximately five times the roller diameter. Consequently, for bending tests used to determine Poisson's ratio, if a region on the sample that is free from roller effects is not chosen, measurement errors as high as 46% can occur. Furthermore, we show that, due to the anisotropy of single crystal Si, this roller-constraining effect depends on crystallographic orientation and is more pronounced when the principal bending axis lies along the <100> direction as compared with the <100> direction.     

碳纤维布与钢板复合加固梁剥离破坏研究

通过12根碳纤维布与钢板复合加固钢筋混凝土梁的抗弯性能研究,结果表明复合加固方式能有效地改善被加固构件的受力性能,但常由于复合加固层的剥离可能导致加固效果的降低。复合加固层与被加固构件之间的剥离是由于薄弱截面在剪应力及正应力的集中作用下而产生的,文中对复合加固层与混凝土之间的粘结剪应力及剥离正应力的计算公式分别进行推导,并进一步对碳纤维布与钢板复合加固的剥离机理进行分析,为工程应用提供依据。     

Interfacial stresses in curved members bonded with a thin plate

The use of steel plates or externally bonded fibre-reinforced polymer laminates for flexural strengthening of concrete, masonry, timber or metallic structures is a technique that has become very popular. The effectiveness of this technique hinges heavily on the performance of the bond between the strengthening plate and the substrate, which has been the subject of many existing studies. In particular, the interfacial stresses between a beam and a soffit plate within the linear elastic range have been addressed by numerous analytical investigations. Surprisingly, none of these investigations has examined interfacial stresses in members with a curved soffit, despite that such members are often found in practice. This paper presents an analytical model for the interfacial stresses between a curved member of uniform section size and a thin plate bonded to its soffit. The governing differential equations for the interfacial shear and normal stresses are formulated and then solved with appropriate simplifying assumptions. Two numerical examples are presented to illustrate the effect of the curvature of the member on the interfacial stress distributions in a simply supported curved beam for the two cases of a point load and a uniformly distributed load. The analytical solution is verified by comparing its predictions with those from a finite element model.     

用波晶片相位板产生角动量可调的无衍射涡旋空心光束

本文提出了一种用波晶片产生无衍射涡旋空心光束的新方案. 根据晶体双折射的性质, 设计波晶片的厚度, 在一块晶体薄片上对o光和e光分别形成各自的四台阶相位板, 线偏振光入射到该相位板后, o光和e光衍射按强度叠加, 利用准伽利略望远镜系统聚焦, 得到近似无衍射涡旋空心光束. 光路简单, 调节方便. 在近轴条件下, 运用菲涅耳衍射理论和经典电磁场角动量理论, 数值模拟计算了周期数不同的两块波晶片相位板衍射光强和角动量的分布, 结果表明: 两块相位板都能在较长距离内产生近似无衍射涡旋空心光束, 光强和轨道角动量的分布与螺旋相位板产生的涡旋光束基本相同. 在衍射光路中加入相位补偿器, 调节o光和e光的相位差可以调节自旋角动量的大小, 从而可以调节总角动量密度和平均光子角动量的大小. 用这种空心光束导引冷原子或冷分子, 原子在与光子相互作用过程中可获得可调的转动力矩.     

电子束放射照相的特性与参数优化

短脉冲强激光产生的电子束具有源尺寸小、脉宽窄、准单能谱等特点, 在放射照相诊断中具有独特作用. 本文通过分析电子在材料中散射并采用蒙特卡罗方法数值模拟, 研究了100 keV到几百MeV能量电子束对有厚度起伏或存在界面的靶的透视, 并与质子、X射线束透视结果比较, 给出了电子束放射照相的特性与参数优化: 基于电子在材料中非弹性散射或能量损失, 选用能量使其射程与靶厚度接近的电子束来诊断靶厚度不均匀性; 基于电子在材料中的弹性散射, 选用射程超过靶厚度的电子束来诊断靶界面.     

用四台阶相位板产生涡旋光束

涡旋光束的产生与应用是当前光学领域的研究热点. 利用傅里叶级数展开法分析了四台阶相位板的相位结构, 发现四台阶相位板可看作是由一系列不同拓扑荷数的螺旋相位板所组成, 用线偏振光直接照射相位板时, 将产生多级衍射光波, 各级衍射光均为不同拓扑荷数的涡旋光波, 由于多级衍射光波间的干涉导致光强分布偏离轴对称分布, 因而与涡旋光波有一定差距. 在此基础上, 提出了用四台阶相位板产生涡旋光束的新方案, 借助于Mach-Zehnder 干涉仪光路, 两块四台阶相位板产生的衍射光干涉叠加, 通过调节干涉仪光路的相位差, 使一部分衍射级干涉相消, 另一部分衍射级干涉相长, 相互加强, 从而把线偏振光转换为涡旋光束. 数值模拟计算了几种周期数不同的四台阶相位板衍射光强和角动量分布, 并与螺旋相位板进行比较, 证明用简单的四台阶相位板不仅能够获得与用螺旋相位板相同的涡旋光束, 而且可以用周期数较小的四台阶相位板产生具有大拓扑荷数的涡旋光束, 降低了制作相位板的难度.     

部分相干平顶光束在非Kolmogorov湍流中的湍流距离

给出了部分相干平顶光束通过非Kolmogorov湍流传输的湍流距离解析表达式,并研究了非Kolmogorov湍流的湍流广义指数、内尺度、外尺度和光束参数对部分相干平顶光束湍流距离的影响。研究表明:湍流距离随相干参数、束腰、外尺度(当湍流广义指数的取值为3.6~4.0时)的增大而减小;随光束阶数、内尺度的增大而增大;随湍流广义指数先减小后增大,且在湍流广义指数取3.11时存在极小值,即光束扩展的极大值。同时利用湍流广义指数及光束参数,具体比较了湍流距离与瑞利区间的大小,并指出光束参数及湍流广义指数决定了湍流是否在瑞利区间内就能对光束扩展构成明显的影响。     

含诱导缺陷薄壁圆管耐撞性优化设计

运用移动最小二乘曲面拟合技术和遗传算法优化技术,建立一套完整的结构耐撞性优化设计技 术。设计了一个具有高效吸能能力的薄壁圆管结构含诱导缺陷薄壁圆管结构,给出了含缺陷薄壁圆管结 构耐撞性优化设计结果。结果显示,设计的薄壁圆管结构具有好的吸能效果,该结构设计简单,便于在结构设 计中使用。     

表面纳米化吸能薄壁多胞结构的数值模拟与设计

采用局部表面纳米化技术和数值模拟方法,对金属薄壁多胞结构的吸能问题开展有限元数值分析和优化设计.结果 显示,局部表面纳米化布局可诱导结构的屈曲变形,并能大幅度提高结构的能量吸收.优化结果还发现,在多胞外壁呈交错矩形格状表面纳米化格局和内附加结构呈均布框架式矩形格状表面纳米化布局情况下,结构屈曲变形稳定且吸能效果最优.该研究为吸能结构的设计提供了依据.     

Moment redistribution in continuous reinforced concrete beams strengthened with carbon-fiber-reinforced polymer laminates

The results of tests on continuous steel-fiber-reinforced concrete (RC) beams, with and without an external strengthening, are presented. The internal flexural steel reinforcement was designed so that to allow steel yielding before the collapse of the beams. To prevent the shear failure, steel stirrups were used. The tests also included two nonstrengthened control beams; the other specimens were strengthened with different configurations of externally bonded carbon-fiber-reinforced polymer (CFRP) laminates. In order to prevent the premature failure from delamination of the CFRP strengthening, a wrapping was also applied. The experimental results obtained show that it is possible to achieve a sufficient degree of moment redistribution if the strengthening configuration is chosen properly, confirming the results provided by two simple numerical models. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 43, No. 5, pp. 667–686, September–October, 2007.