Development of poly(vinyl chloride)/montmorillonite nanocomposites using chelating agents

Different chelating agents such as poly(ethylene glycol), propylene glycol monooctadecanoate and palm oil were used for modification of the surface-treated montmorillonite (MMT). The work also included the development of a technique for mixing chelating agents with MMTs using different methods and different proportions of MMT/chelating agent/ethanol. Evaluation of the result of mixing was performed by thermogravimetric analysis, X-ray diffraction and high-resolution scanning electron microscopy (HR-SEM). The results showed that the chelating agents used were intercalated in MMT, increasing the interlayer spacing. The OMMT was used in the manufacture of composites with rigid PVC using a microcompounder. The master batch concept turned out to be promising in terms of dispersion and delamination of clay, as observed in HR-SEM photographs. However, despite good dispersion and exfoliation of MMT, poor compatibility between clay platelets and PVC matrix remains to be solved to enable full exploitation of its engineering potential. Despite this drawback, good thermal stability and mechanical properties have already been achieved.     

Microwave-assisted synthesis of dihydropyridones from curcumin

Dihydropyridones were prepared by microwave-assisted reaction between curcumin and primary amines or their acetates in the presence of Montmorillonite (K-10) as a catalyst. The reaction was complete within a few minutes and the yield depends on the amine used.     

A structural model for the time-dependent recovery of mineral suspensions

A thixotropic recovery model has been developed that is based on consideration of the microstructural interactions that occur between particles within a suspension particle network. The model is based on Smoluchowski coagulation rate theory, utilizing second order kinetics to describe the thixotropic recovery behavior. The model is applied to Na-montmorillonite-based coal tailings suspensions and is also shown to be applicable to brown coal and bauxite residue suspensions. The model describes all the recovery data well, especially at intermediate to large recovery times. The recovery of the montmorillonite suspensions at short times was faster than predicted, indicating the existence of additional factors in early-time structure development. The discrepancy may have also been due to the highly anisotropic nature of the clay platelets. The recovery rate constant, K _r , increases with increasing solids concentration (for constant surface chemical conditions) as would be expected from the basis of the model. Received: 22 September 2000 Accepted: 16 March 2001     

FTIR analysis of bentonite in moulding sands

Bentonite is used in a wide range of applications. One of them is the foundry industry. The aim of this study was to investigate modification of moulding sands by dust which is generated during foundry process. Recycling of this dust is very important from ecological point of view. The samples of moulding sands were examined by Fourier Transform Infrared spectroscopy (FTIR). Analysis of the bands due to the Si–O stretching vibrations allows to reveal the changes of active bentonite and silica sand, i.e. the main components of the moulding sands. FTIR results are compared with technological properties of the materials studied. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) methods have been used as the complementary measurement.     

Effect of iron and humic acid on photodegradation of some pesticides adsorbed on clay surfaces

Photochemistry studies can be helpful in assessing the environmental fate of chemicals. For this reason, the photodegradation kinetic studies of the two pesticides orthophenylphenol (OPP) and monuron, largely used in agriculture, were carried out in solid phase. The fungicide OPP and the herbicide monuron were irradiated on the clay fractions (montmorillonite and modified clays) using a suntest simulator. The phototransformation of the parent compound was followed by HPLC technique. The photodegradation process appears to follow the first order reaction. Kinetic parameters were determined and the experimental results show that the photodegradation of these substrates was enhanced in presence of K-montmorillonite, in comparison with Fe(III) exchanged montmorillonite and montmorillonite complexed with humic acid complexes. This study has shown that the iron and humic acid adsorbed on clay surfaces did not increase the degradation rate.     

Preparation and characterization of exfoliated polystyrene/clay nanocomposites using a cationic radical initiator-MMT hybrid

The exfoliated polystyrene (PS)/clay nanocomposites were prepared via in situ polymerization using a cationic radical initiator-intercalated montmorillonite hybrid. The exfoliated structure resulted from the predominant intra-gallery polymerization over the extra-gallery polymerization owing to the anchored radical initiator inside the clay galleries. Several critical properties of the nanocomposites such as the initial thermal degradation temperature, glass transition temperature, storage modulus, Young’s modulus, and tensile strength were estimated and compared with earlier reported literature values. The improvements in such properties were either comparable or much greater than the reported literature values, mainly due to the efficient exfoliation and dispersion of the clay in the PS matrix.     

Dephosphatation under UV light of water by Ti-PILC with activation by secondary species (La,Se, and Rb)

Me/Ti-PILC catalysts (Me: La, Se, Rb) were prepared with 60% in weight of Ti-species and 3% in weight of Me-secondary species added under ultrasounds. All materials were characterized by XRF, XPS, XRD, BET, HR-TEM/EDS, FEG-SEM and UV-vis. Three kinds of Ti-oxide nanoparticles were identified: (1) Ti-pillars within the clay layers, (2) rutile nanoflowers, and (3) anatase. In UV-vis spectra, no significant change in the band-gap was observed. In La and Se samples, small variations of the anatase XRD lines are associated with cationic diffusion after deposition of secondary species and calcination. An O1s XPS-peak (533.5 eV) is attributed to oxygen vacancies generated by this diffusion. Phosphate photo-removal in water was studied using phosphoric acid solution (75.97 g L⁻¹). Dephosphatation is significantly improved in the presence of Me-species as La/Ti-PILC > Se/Ti-PILC > Rb/Ti-PILC > Ti-PILC. Partial dephosphatation by adsorption is possible in the dark but is strongly improved by UV irradiation. With a La catalyst and under UV irradiation, phosphates (6.6 × 10⁻³ mol L⁻¹) were recovered in less than 70 min. Therefore, Me/Ti-PILC have a great potential as photocatalysts for the treatment of wastewaters and the recovery of phosphates.     

Dynamic melt flow of nanocomposites based on poly-ɛ-caprolactam

 The dynamic flow behavior of polyamide-6 (PA-6) and a nanocomposite (PNC) based on it was studied. The latter resin contained 2 wt% of organoclay. The two materials were blended in proportions of 0, 25, 50, 75, and 100 wt% PNC. The dynamic shear rheological properties of well-dried specimens were measured under N₂ at T=240 °C, frequency ω=0.1–100 rad/s, and strains γ=10 and 40%. At constant T, γ, and ω the time sweeps resulted in significant increases of the shear moduli. The γ and ω scans showed a complex rheological behavior of all clay-containing specimens. At γ=10% the linear viscoelasticity was observed for all compositions only at ω>1 rad/s, while at γ=40% only for 0 and 25 wt% of PNC. However, the effect was moderate, namely decreasing G′ and G′′ (at ω=6.28 rad/s; γ=50%) by 15 and 7.5%, respectively. For compositions containing >25 wt% PNC two types of non-linearity were detected. At ω≤ω_c=1.4 ± 0.2 rad/s yield stress provided evidence of a 3-D structure. At ω > ω_c, G′ and G′′ were sensitive to shear history – the effect was reversible. From the frequency scans at ω > ω_c the zero-shear relative viscosity vs concentration plot was constructed. The initial slope gave the intrinsic viscosity from which the aspect ratio of organoclay particles, p=287 ± 9 was calculated, in agreement with the value calculated from the reduced permeability data, p=286. Received: 24 May 2001 Accepted: 27 August 2001     

Colloidal forces between bitumen surfaces in aqueous solutions measured with atomic force microscope

Colloidal forces between bitumen surfaces in aqueous solutions were measured with an atomic force microscope (AFM). The results showed a significant impact of solution pH, salinity, calcium and montmorillonite clay addition on both long-range (non-contact) and adhesion (pull-off) forces. Weaker long-range repulsive forces were observed under conditions of lower solution pH, higher salinity and higher calcium concentration. Lower solution pH, salinity and calcium concentration resulted in a stronger adhesion forces. The addition of montmorillonite clays increased long-range repulsive forces and decreased adhesion forces, particularly when co-added with calcium ions. The measured force profiles were fitted with extended DLVO theory to show the repulsive electrostatic double layer and attractive hydrophobic forces being the dominant components in the long-range forces between the bitumen surfaces. At a very short separation distance (less than 4–6 nm), a strong repulsion of steric origin was observed. The findings provide a fundamental understanding of bitumen emulsion stability and a mechanism of bitumen “aeration” in bitumen recovery processes from oil sands.     

蒙脱石修饰碳糊电极测定氨基酸的研究：Ⅱ.酪氨酸的测定

本文报道蒙脱石修饰碳糊电极测定酪氨酸，在０．００１ｍｏｌ／Ｌ ＫＣｌ－ＨＣｌ（ｐＨ＝２．０）溶液中开路富集，介质交换后微分脉冲阳极溶出伏安法测定，在０．５－２．５μｇ／ｍｌ范围内有线性，检测限为６３ｎｇ／ｍｌ。可避免其他氨基酸，微量元素和常量金属元素的干扰，直接用于氨基酸药物样品的分析，获得了满意的结果，还对酪氨酸在电极上的反应机理进行了探讨。