Influence of Yb-Doped Nanoporous TiO2 Films on Photovoltaic Performance of Dye-Sensitized Solar Cells

Yb-doped TiO2 pastes with different Yb/TiO2 weight ratios are prepared in the sol-gel process to obtain dyesensitized solar cells （DSCs）. The nanocrystalline size of Yb-TiO2 becomes smaller and the lattice parameters change. Lattice distortion is observed and dark current is detected. It is found that a part of Yb existing as insulating oxide Yb2O3 state acts as barrier layers at the electrode-electrolyte interface to suppress charge recombination. A Yb-doped TiO2 electrode applied in DSCs leads to a higher open-circuit voltage and a higher fill factor. How the Yb-doped TiO2 films affect the photovoltaic response of DSCs is discussed.     

Formation of Interfacial Layers in LaAlO3/Silicon during Film Deposition

We have studied the interracial reactions between amorphous LaAlO3 thin films and Si substrates, using high- resolution transmission electron microscopy and x-ray photoelectron spectroscopy. It has been shown that the interracial layer between LaAlO3 film and Si substrate chemical states show that the ratio of La 4d3/2 to Al 2p is SiLaxAlyOz. The depth distributions of La, Si and Al of the interfacial layer remains unchanged with the depth compared to that of the LaAlO3 film. Moreover, the Si content, in the interracial layer gradually decreases with increasing thickness of the interracial layer. These results strongly suggest that the Al element is not deficient in the interracial layer, as previously believed, and the formation of a SiLaxAlyOz interracial layer is mainly due to the diffusion of Si from the substrate during the LaAlO3 film deposition. With the understanding of the interracial layer formation, ones can control the interface characteristics to ensure the desired performances of devices using high-k oxides as gate dielectrics.     

LD Pump Single-Longitudinal-Mode Nd：GdVO4/RTP Solid-State Green Laser

The single-longitudinal-mode Nd：GdVO4/RTiOPO4 （RTP） solid-state Green laser operation of a laser-diode （LD） end-pumped laser is realized by multi-cavities and a Brewster plate. The LD-pumped single-frequency green laser has been demonstrated by optimizing several parameters and a cavity length, with precise temperature controlling of Nd：GdV04, RTP and laser diode. When the incident pump power is 2 W at 808.4 nm, a single-frequency cw green laser at 532nm with output 210 m W is obtained, the optical-to-optical conversion efficiency is up to 10.5%.     

精密垫片精冲工艺有限元分析与模具设计

精密垫片零件，如图1所示，零件材料为1Cr18Ni9Ti，强度大（σb=650MPa），有一定塑性。从零件尺寸精度看，φ4mm外圆为IT7级精度，φ4mm外圆与φ2mm内孔有很高的同轴度要求，冲裁断面与零件两端面有垂直度要求，普通冲压不能达到零件精度：从工序的角度看，有冲孔和落料工序，剪切面粗糙度Ra≤3．2μm，属于光洁冲裁范畴；另外，技术条件中要求零件两大面不得有任何划伤，且光滑平整。总体上看，该零件的冲压加工性不好，难度较大，对模具的设计、选材、制造要求都较高。     

复合薄膜透湿率对分子筛吸附性能的影响

分子筛经活化后用复合薄膜包装袋封装存放一定时间后使用，由于水汽缓慢渗透和包装袋微量泄漏的存在，可能使分子筛吸湿，从而直接影响其使用效果和有效期，因此试验研究分子筛产品包装贮存前后吸附性能的变化，以验证理论计算结果，并为分子筛应用提供重要的试验依据。     

CHBr薄膜制备的初步研究

碳氢（cH）及其掺杂材料常被用作ICF实验靶丸烧蚀层材料。制备CH薄膜及其掺杂材料的方法有很多，诸如：离子束辅助沉积、离子溅射沉积、低压等离子体化学气相沉积（LPPCVD）等。近年来，详细研究了LPPCVD法制备CH薄膜的制备方法与工艺，形成了比较成熟的技术路线与工艺路线，并为“神光”实验提供了一系列实验靶丸。     

Fe/Si多层膜的层间耦合与界面扩散

对以本征Si及重掺杂ｐ型和ｎ型Si作为中间层的Fe/Si多层膜的层间耦合进行研究，并通过退火，增大Fe，Si之间的扩散，分析界面扩散对层间耦合的影响. 实验结果表明，层状结构良好的制备态的多层膜，Fe，Si之间也存在一定程度的扩散，它是影响层间耦合的 主要因素，远远超过了半导体意义上的重掺杂，使不同种类的Si作为中间层的层间耦合基本 一致.进一步还发现，在一定范围内增大Fe，Si之间的扩散，即使多层膜的层状结构已经有了相当的退化，Fe/Si多层膜的反铁磁耦合强度基本保持不变. 关键词： Fe/Si多层膜 层间耦合 界面扩散     

红光激发下掺Ho3+氟化物薄膜的上转换发光

利用激光脉冲沉淀法制备了稀土Ho~(3 )掺杂的氟化物薄膜。观测到处于薄膜中的Ho~(3 )离子在632.8nm红光激发下的上转换发射。这些上转换发射包括:~5S_2→~5I_7,~5F_4→~5I_7和~5S_2→~5I_8。     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。