热塑性聚酯醚液晶弹性体的合成与表征

液晶聚酯醚嵌段共聚物是一类新型的高分子材料,已有较多研究［１～３］．当共聚物中软、硬段比例适当,在一定温度范围内,这类液晶聚合物可能出现高弹性．但系统报道聚酯醚液晶弹性体的工作并不多．Ｌｅｎｚ［２］报道得到了类似橡胶的低强度、低模量和高伸长率的液晶弹...     

甲壳素/甲壳胺的聚集态结构及性能

制备了不同脱乙酰度的甲壳素,并对脱酰化反应进行了研究,找出了适合不同脱酰度甲壳素的溶剂,探讨了制样温度与甲壳胺膜的结晶形态和力学性能之间的关系,比较了甲壳素、甲壳胺及不同来源甲壳素的结晶形态.     

铜树枝晶的水热合成以及结构表征和抗菌性能评价(英文)

在乙醇胺-水混合溶液中采用水热处理硫酸铜的方法制备了多结构的铜树枝晶;采用X射线粉末衍射仪、扫描电子显微镜、透射电子显微镜分析了所得样品的结构和形貌;采用牛津杯法评价了其对金黄葡萄球菌、枯草芽孢杆菌、大肠杆菌和绿脓杆菌的抗菌性能.结果表明,铜树枝晶由一个长的一级中心主干和许多高度对称分布在主干两侧的二级分支结构构成,且形貌均匀;反应温度、反应时间以及溶剂组成对铜树枝晶的形貌有很大影响.与此同时,铜树枝晶表现出选择性的抗菌行为,对金黄葡萄球菌、枯草芽孢杆菌和绿脓杆菌更有效.     

Role of emulsifier on the particle size and polymer particle size distribution using multiwavelength spectroscopy measurements

Latex emulsions depend strongly on the polymer composition, and particle size distribution, which in turn, is a function of the preparation of the latex and on the formulation and composition variables. This study reports measurements of particle size and particle size distribution of latex emulsions as function of the reaction time and the type and concentration of emulsifier by using the multiwavelength spectroscopy technique. Results show changes in the particle size of latex emulsions with the reaction time, obtaining larger particles and broader distributions with increasing of Tween 80 ratio. The steric stabilization provides the sole nonionic emulsifier is not enough to protect the polymer particle, causing the flocculation among the interactive particles, resulting in unstable latex. However, latex emulsions prepared with Tween 80 ratio <70 wt.% can stabilize efficiently the nucleated particles, probably due to the effects provided by both, the electrostatic and steric stabilization mechanisms. The same effect is shown in the curves of conversion (%) as a function of reaction time, resulting in slower polymerization rate for Tween 80 ratio >70 wt.%. On the other hand, smaller polymer particles, in all range of emulsifier mixture, have been obtained to higher emulsifier concentration.     

Preparation and characterization of poly(m-xylylene oxamide) and its copolymer

New polyoxamides, poly(m-xylylene oxamide) (PMXD2) and its copolymer with 2-methyl-1,5- pentanediamine (P(MXD2/M52)) with relative viscosity up to 4.6 were synthesized via spray/solid state polymerization. The obtained polyoxamides were characterized by FTIR, NMR, WAXD, DSC and TGA. The T_m of the copolymers decreased with increasing percentage of poly(2-methyl-1,5- pentaneoxamide) (PM52) in the copolymer from 346°C for 100% poly(meta-xylyleneoxamide) (PMXD2) to 277°C for copolymers of PMXD/PM52 (60/40). TGA analysis revealed that the thermal stability of the copolymers compared well with commercial PA6 and XRD studies suggested the copolymers possessed high crystallinity. DMA profile of the PMXD/PM52 (70/30) copolymer showed better mechanical performance with a storage modulus of about 7.2 GPa as compared to 1.8 GPa of PA6 at 25°C.     

锐钛矿型TiO2担载的Pd催化剂用于乙炔选择加氢的催化性能及其表征

Anatase TiO₂ nanospindles containing 89% exposed {101} facets (TiO₂-101) and nanosheets with 77% exposed {001} facets (TiO₂-001) were hydrothermally synthesized and used as supports for Pd catalysts. The effects of the TiO₂ materials on the catalytic performance of Pd/TiO₂-101 and Pd/TiO₂-001 catalysts were investigated in the selective hydrogenation of acetylene to polymer-grade ethylene. The Pd/TiO₂-101 catalyst exhibited enhanced performance in terms of acetylene conversion and ethylene yield. To understand these effects, the catalysts were characterized by H₂ temperature-programmed desorption (H₂-TPD), H₂ temperatureprogrammed reduction (H₂-TPR), transmission electron microscopy (TEM), pulse CO chemisorption, X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA). The TEM and CO chemisorption results confirmed that Pd nanoparticles (NPs) on the TiO₂-101 support had a smaller average particle size (1.53 nm) and a higher dispersion (15.95%) than those on the TiO₂-001 support (average particle size of 4.36 nm and dispersion of 9.06%). The smaller particle size and higher dispersion of Pd on the Pd/TiO₂-101 catalyst provided more reaction active sites, which contributed to the improved catalytic activity of this supported catalyst.     

Understanding the effect of filler shape induced immobilized rubber on the interfacial and mechanical strength of rubber composites

Styrene butadiene rubber (SBR) composites with silica, halloysite nanotubes (HNTs) and montmorillonite (MMT) were prepared and the interfacial and mechanical properties were compared to understand the reinforcing behaviours of these fillers based on the results of SEM, DSC, DMA, etc. Due to the formation of interparticle domain, HNTs immobilized more rubber approaching their surface than silica and MMT. Interestingly, only tightly immobilized rubber chains made contribution to the enhancement of interfacial and mechanical strength of SBR composites. This was because the tightly immobilized rubber acted as a bridge in the filler-rubber interface and induced the formation of stretched rubber chains linked filler network when the composites were loaded in tension, while loosely immobilized rubber were easy to slip off from filler surface, causing the separation between filler and bulk rubber. Therefore, silica with more tightly immobilized rubber approaching its surface showed better reinforcing effect on rubber than HNTs and MMT.     

Morphological,rheological, crystalline and mechanical properties of ethylene-vinyl acetate copolymer/linear low-density polyethylene/amphiphilic graphene oxide nanocomposites

Chemical modification of graphene oxide has become a popular method for imparting unique properties to extend its application. Here, we show a simple way to synthesize amphiphilic graphene oxide (AGO) by grafting quaternary ammonium salt onto GO sheets. The AGO sheets not only showed high thermal stability and good dispersion in many polar and non-polar solvents in comparison to GO sheets but also the chemical modification maintained the two-dimensional structure. As a result, the AGO sheets improve the interfacial interaction between ethylene-vinyl acetate copolymer (EVA) and linear low-density polyethylene (LLDPE). Because of the large size of AGO, the location of AGO is very dependent on the mixing strategy. The AGO was dispersed in the EVA phase when AGO was mixed first with EVA and then with LLDPE, whereas it was confined in the LLDPE phase when AGO was mixed first with LLDPE and then with EVA. AGO sheets were found at the interface of LLDPE and EVA when AGO, EVA, and LLDPE were mixed together, suggesting that AGO has a high interfacial interaction with both LLDPE and EVA. These high interfacial interactions lead to high tensile strength, Young's modulus, complex viscosity and crystallization temperature in comparison to the EVA/LLDPE blends without AGO sheets.     

反-4-(反-4'-正丙基环已基)环已醇的合成与表征

环己烷类液晶因具有高度的稳定性,较宽的相列相温区而受到人们的青睐。反-4-(反-4’-正丙基环己基)环己醇(trans-3HHE)是一种合成环己烷类液晶的重要中间体,它可通过酶选择性催化和顺式构型异构化二种方法合成。文献报道顺式构型异构化法是：4-(反-4’-正丙基环己基)苯酚以铑／碳或铑／氧化铝为催化剂,在酸性介质条件下进行加氢反应,