High temperature corrosion behaviour of M(Co,Ni)CrAIY-coatings on high temperature materials-microanalytical investigations

In our former investigations, the phenomenon high temperature corrosion (HTC) was described exemplarily on selected materialcoating combinations for blades of stationary gas turbines, mainly in the temperature region of up to 750° C. To answer the question, in which manner higher gas inlet and/or higher material surface temperature would influence the HTC behaviour, a special analytical technique—the integral layer profile analysis—was introduced to ameliorate concentration profile methods. By examining IN 738 LC specimens with CoCrAlY plasma spray coating, stressed by hot gas at 900° C, the limits of this system are shown by explaining the corrosion mechanism; the method is also used for other systems, e.g. U 520 with NiCrAlY coating at 750° C.     

Formation at low surfactant concentrations and characterization of mesoporous MCM-41

At low concentrations of cetyltrimethylammonium bromide,all silica-based mesoporous materials with hexagonal phase have been synthesized via interactions between self-assembled surfactant molecule aggregates and aniomc silicate polymers.The resulting materials are characterized by XRD,FT-IR,solid state 29Si MAS NMR,thermal analysis and N2 adsorption-desorption measurements.After soluble ions are removed,the interactors between surfactant micelles and silicate polymers are reorganized and then form mesostructures 1 he hexagonal framework is sonsistent with amorphous silica gel.The structures of materials depend on the synthesis conditions Hydrothermal process improves the interactions between molecules and increases the degree of framework silicon atom polymerization The.surface area and the mesopore volume of the material prepared at 100℃ increase by 87% and 71 %,respectively,compared with those obtained at room temperature.     

离聚体的结构表征 Ⅲ.EXAFS法测定含氟的铜离聚体的精细结构

本文报道了用先进的EXAFS及ESR等方法研究了羧酸型含氟的铜(Ⅱ)离聚体离子微区的内部精细结构,结果表明,铜离聚体的离子微区主要由羧酸根桥键的双核配位结构单元及平面四方形的配位结构单元等聚集而成。在双核配位结构单元中第一层为Cu~(2+)—O配位,配位数为4,配位键键长为1.96A,第二配位层为Gu~(2+)—Cu~(2+)配位,Cu~(2+)—Gu~(2+)间距为2.64A。平面四方形的配位结构单元Cu~(2+)—O的配位数为4,配位键键长为1.96A。共聚物中羧基含量对离聚体的基本配位结构单元和离子微区的精细结构影响较小,但对微区大小有影响。     

3-苄基-4-氨基-5-芳胺基-1,2,4-三唑的合成与表征

酰氨基硫脲是一类重要的有机合成中间体[1-3]。其最终产物大都有消炎、镇痛、抗菌、杀虫、除草、调节植物生长等生理活性。本文以苯乙酸乙酯与芳胺为基本原料,经多步反应,制得1 苯乙酰基 4 芳基氨基硫脲,研究了它们在水合肼存在下的关环反应,合成了3 苄基 4 氨基 5 芳胺基 1,2,4 三唑,其结构经元素分析、红外光谱、核磁共振氢谱、碳谱表征。1　实验部分1 1　仪器与试剂ＸＴ4Ａ型显微熔点仪(温度计未校正);ＣＥ公司(意大利)Ｆｌａｓｈ1112型自动元素分析仪;Ｂｒｕｋｅｒ公司(德国)Ｅｑｕｉｎｏｘ55型红外分光光度计,ＫＢｒ压片;Ｂｒｕｋ…     

Novel Poly（thienylene Ethynylene）s with Electron-accepting Groups

Since the early works of A. J. Heeger, A G. MacDiarmid and Hideki Shirakawa on semiconducting polymers, π-conjugated oligomers and polymers have been actively investigated for a variety of optoelectronic applications, such as field effect transitors (FET…     

锂离子二次电池电解质材料LiPF6的制备及表征

0引言 液态锂离子电池自1990年开发成功以来,由于具有比能量高、工作电压高、应用温度范围宽、自放电率低、循环寿命长、无污染、安全性能好等许多独特的优势[1],所以其发展前景十分广阔.目前液态锂离子二次电池中开发使用的无机阴离子导电盐主要有LiClO4、LiPF6、LiAsF6等,但LiClO4为强氧化剂,使用不安全而不宜用于电池,LiAsF6虽然性能颇佳,但有毒且价格较贵,故也不宜广泛使用.LiPF6被认为是目前较合适的电解质[1],但其制备困难,价格较贵,且目前报道的合成方法也多是以HF为介质[2～5].本文作者以PF5和LiF为原料在CH3CN溶剂中简单有效地合成了高纯LiPF6,并通过在手套箱中制样的方法对目标产物进行了红外、热重和X射线衍射分析,给出了LiPF6的红外光谱图、热重分析数据和X射线衍射图.     

Studies on alkaline protease produced by Bacillus sp. NG312

An alkalophilic hyperproducer of alkaline protease, Bacillus sp. NG312, was isolated, and the enzyme showed maximum activity at pH 11.0 and 60°C. The temperature optimum was increased by 10°C in presence of Ca²⁺. The crudeenzyme was found to have half-life of 11 d at 37°C and maximum stability at pH 9.0–10.0. It also exhibited very good stability in presence of detergent components and some locally available commericial detergent powders.     

Mechanical properties of BPDA-ODA polyimide fibers

An aromatic polyimide was synthesized via a one-step polycondensation reaction between biphenyltetracarboxylic dianhydride (BPDA) and 4,4′-oxydianiline (ODA) in p-chlorophenol. The polyimide (BPDA-ODA) solution dopes were spun into fibers by means of dry-jet wet spinning. The as-spun fibers were drawn and treated in heating tubes for improving the mechanical properties. The thermal treatment on the fibers resulted in a relatively high tensile strength and modulus. Thermal mechanical analysis (TMA) was employed to study the linear coefficient of thermal expansion (CTE). Thermal gravimetry analysis (TGA) spectra showed that the BPDA-ODA fibers possessed an excellent property of thermo-oxidative degradation resistance. The sonic modulus E_s of the polyimide fibers was measured.     

Purification and partial characterization ofRhizomucor miehei lipase for ester synthesis

A commercialRhizomucor miehei lipase was purified by ammonium sulfate precipitation. Phenyl Sepharose 6 Fast Row hydrophobic interaction chromatography, and DEAE Sepharose Fast Flow anion-exchange chromatography. The recovery of lipase activity was 32% with a 42-fold purification. The molecular size of the purified enzyme was 31,600 Dalton and the pI 3.8. The enzyme was stable for at least 24 h within a pH range of 7.0-10.0, and 96.8% of the enzyme activity remained when kept at 30‡C for 24 h. Further, about 10–30% of the lipase activity was inhibited by K⁺, Li⁺, Ni⁺, Co²⁺, Zn²⁺, Mg²⁺, Sn²⁺, Cu²⁺, Ba²⁺, Ca²⁺, and Fe²⁺ ions and by SDS, but EDTA had no effect. Under the experimental conditions, the optimum temperature for the hydrolysis of olive oil was 50‡C (pH 8.0), and for the synthesis of 1-butyl oleate, 37‡C. It was concluded that hydrolytic activity of lipase alone is not a sufficient criterion for its synthetic potential. The optimal molar ratio of oleic acid and 1-butanol was 2:1 for 1-butyl oleate synthesis. The 1-butyl oleate yield was unaffected by purification of the enzyme after 12 h.     

CeO2—LnO1.5固溶体的表征及其甲烷催化燃烧性能

向CeO2中引入Ln3 离子后形成的CeO2－LnO1.5（Ln=La，Nd，Sm，Gd）固溶体（n（Ce）：n（Ln）=1：1）是一种无贵金属的新型高效甲烷燃烧催化剂．比表面、XRD、Raman、TEM等分析证实，这类固溶体具有部分畸变的萤石结构，Ln3 进入晶格后诱发的结构变化使得团溶体的表面和本体能同时参与氧化还原反应．实验表明，该固态溶液体系是甲烷催化燃烧的良好催化剂．