Rheological properties of paraffin suspensions of surface-modified alumina powder for low-pressure injection moulding

Due to the hygroscopic nature of fine alumina powders, the presence of water may have a detrimental effect on the rheological properties of a suspension in melted paraffin for low-pressure injection moulding (LPIM). For this reason, a modification of the powder surface from hydrophilic to hydrophobic is essential for the production of high-quality moulded ceramics. In our paper, the efficiency of the application and the chemisorption of protective monomolecular layers of a long-chain carboxylic acid or its salts will be presented. The effect of the powder treatment on the shear viscosity and the viscoelastic properties of the suspensions for LPIM as well as on their stability in terms of the detrimental effect of water will be discussed.This paper was presented at the first Annual European Rheology Conference (AERC) held in Guimarães, Portugal, September 11-13, 2003.     

流动注射在线萃取-有机相ICP-AES法测定矿石中的痕量金

提出了一种流动注射在线萃取－有机相ＩＣＰ－ＡＥＳ法测定矿石中痕量金的分析方法,研究了流动注射在线萃取与ＩＣＰ－ＡＥＳ法的联用技术,设计了在线萃取流路,优化了各项化学条件及流路参数。该方法操作简便,快速,检出限为０．００１μｇ／ｍＬ,相对标准偏差（ＲＳＤ）为３．４％,应用于矿石中痕量金的分析,获得满意的结果。     

Effect of the stagnation temperature on supersonic flow parameters: Application for air in nozzles

When the stagnation temperature of a perfect gas increases, the specific heats and their ratio do not remain constant any more and start to vary with this temperature. The gas remains perfect and its state equation always remains valid, except it will be called a calorically imperfect gas. The aim of this research is to develop the relations of the necessary thermodynamics and geometrical ratios and to study the supersonic flow at high temperature (lower than the threshold of dissociation). The results are found by the resolution of nonlinear algebraic equations and integration of complex analytical functions where the exact calculation is impossible. The dichotomy method is used to solve the nonlinear equation, and the Simpson algorithm is used for the numerical integration of the found integrals. A condensation of the nodes is used, since the functions to be integrated have a high gradient at the extremity of the interval of integration. A comparison is made with a calorifcally perfect gas to determine the error of this. An application is made for air in a supersonic nozzle. The text was submitted by the authors in English.     

Injection locked multi-section gain-coupled dual mode DFB laser for terahertz generation

A dual mode multi-section gain-coupled distributed feedback laser with tunable mode spacing is subharmonically injection locked at 0.315 THz. The injected signal consists of an optical comb with harmonics 35 GHz apart and a bandwidth of approximately 1.9 THz. The optical comb is a result of strong four-wave mixing in a highly-nonlinear dispersion-shifted fiber. In order to observe locking of the multi-section laser, the output is optically downconverted to RF frequencies using the same optical comb. The locked multi-section DFB laser is a coherent and tunable optical source suitable for continuous-wave terahertz generation systems.     

Influence of processing methods on starch properties

Native potato starch was prepared using different processing methods. The samples were characterized by wide-angle X-ray scattering (WAXS), optical microscopy, differential scanning calorimetry (DSC), and microhardness. Compression molding of the starch granules led to sintered relatively brittle materials. Here, the amylopectin crystals of the native powder remained grossly preserved. Preparation of dry films from aqueous gels resulted in disintegration of the structure of the native starch granules and in the formation of a new semicrystalline structure comprised of crystallized amylose molecules. Injection molding of native starch was found to be a processing method that gives rise to amorphous materials with superior mechanical properties.     

Continuous flame oxidation in supercritical water

Abstract

Continuous flames have been observed in Supercritical water oxidation (scWO) of isopropyl alcohol (IPA), using a vertical continuous reactor with sapphire windows and a mixing nozzle. Two types of continuous flame were confirmed: the one was long pale blue colored and the other was red short cone shaped, changing blue to red at around air ratio 2.0. The flame was strongly influenced by IPA concentration, air ratio and design of the mixing nozzle. Results for decomposition of PA are presented for IPA concentrations ranging from 600 up to 28260 ppm as TOC and initial reactor temperatures, were mostly around 490°C, at 25 MPa. Decomposition rate at steady state was over 99.9%. Experimentally measured CO₂ and O₂ concentrations at the flue gas were in good agreement with theoretically calculated values. Even for low air ratio as 1.1, high decomposition rate without CO, NO, NO₂ was achieved.     

Investigation of water absorption in clay-reinforced polypropylene nanocomposites

The behaviour of polypropylene nanocomposites containing different amounts of commercial nanoclay upon exposure to distilled water and sea water at different temperatures was investigated and compared with that of neat polypropylene. In the initial stages, the weight gain (moisture absorption) follows Fick's second law, but at longer times deviations are observed owing to physical degradation and in some cases a loss of mass. Distilled water diffuses more rapidly than sea water. As the nanoclay content increases, both the rate of moisture absorption and the maximum moisture content increase, owing to the hydrophilic nature of the nanoclay and the added compatibilizing agent. Although the moisture absorption decreases the flexural properties of both the nanocomposites and neat PP, because the unexposed (as-moulded) nanocomposites are significantly superior to the neat PP they remain so even after prolonged exposure.     

Use of an injection port for thermochemolysis–gas chromatography/mass spectrometry: Rapid profiling of biomaterials

A simple and direct approach was developed for thermochemolytic analysis of a wide range of biomolecules present in plant materials using an injection port of a gas chromatograph/mass spectrometer (GC/MS) and a novel solids injector consisting of a coiled stainless steel wire placed inside a modified needle syringe. Optimum thermochemolysis (or Thermally Assisted Hydrolysis/Methylation) was achieved by using a suitable methanolic solution of trimethylsulfonium hydroxide (TMSH) or tetramethylammonium hydroxide (TMAH) with an injection port temperature of 350 °C. Intact, methylated flavonoids, saccharides, phenolic and fatty acids, lignin dimers and diterpene resin acids were identified. Samples include tea leaves, hemicelluloses, lignin isolates and herbal medicines. Unexpected chromatographic results using TMAH reagent revealed the presence of intact methylated trisaccharides (658 Da) and structurally informative dimer lignin markers.     

停流-分光光度法流动注射络合滴定铝

推导出了停流法流动注射络合滴定的理论公式，计算了简单易实现的流路图，详细观察分析了流动注射络合滴定中的样品带与试剂流混合后在流通池中的吸光度变化。从理论上分析并预测了停流流动注射络合滴定的性质。     

A computational study of gas flow in a De‐Laval micronozzle at different throat diameters

A numerical study has been carried out to investigate the gas flows in a micronozzle using a continuum model under both slip and no‐slip boundary conditions. The governing equations were solved with a finite volume method. The numerical model was validated with available experimental data. Numerical results of exit thrust showed good agreement with experimental data except at very low Reynolds numbers. For parametric studies on the effect of geometric scaling, the nozzle throat diameter was varied from 10 to 0.1 mm, whereas throat Reynolds number was varied from 5 to 2000. A correlation has also been developed to calculate the specific impulse at specified throat diameter and Reynolds number. The effect of different gases on the specific impulse of the nozzle, such as helium, nitrogen, argon and carbon dioxide, was also examined. Copyright © 2008 John Wiley & Sons, Ltd.