锂离子电池正极材料LiMn2O4的低热固相合成与性能表征

锂离子电池具有比能量高、环境污染小等优点,广泛应用于手提电话、便携式电脑、摄像机等设备中。其正极材料的研究是锂离子电池的研究重点。层状结构的LiCoO2、LiNiO2和尖晶石结构的LiMn2O4是仅有的三种能在3.5V以上电位可嵌入Li的正极材料[1~3]。目前市售的锂离子电池主要采用LiCoO2作正极材料,但由于Co资源缺乏和价格相对昂贵,而锰资源丰富,价格低廉且无毒,对环境友好,因此世界各国都在大力进行以LiMn2O4为正极材料的锂离子电池的实用化研究。LiMn2O4传统的制备方法是高温固相反应合成法[4~7],但由于Mn的变价多,与Li形成贫Li或…     

Fluorenyl-containing sulfonated poly(aryl ether ether ketone ketone)s (SPFEEKK) for fuel cell applications

A series of fluorenyl-containing sulfonated poly(aryl ether ether ketone ketone)s (SPFEEKK) were synthesized via aromatic nucleophilic substitution polymerization. The sulfonation content (SC) was controlled by the feed ratios of sulfonated and nonsulfonated monomers. Flexible and strong membranes in the sulfonic acid form were obtained from cast membranes in the sodium salt forms by treatment with acid. The thermal properties, water uptake, swelling ratio, water state, oxidative stability, proton conductivity and methanol permeability were investigated. All the polymers had proton conductivities greater than 1 × 10⁻² S/cm at room temperature, and the conductivity values of m-SPFEEKK-80 and p-SPFEEKK-80 were up to 1.86 × 10⁻¹ and 1.78 × 10⁻¹ S/cm at 100 °C. This series of polymers also possessed good dimensional stability in water and low methanol crossover.     

Conservation of [(C2H4NH3)3N]2·(ZrF7)2·H2O layers during the topotactic dehydration of [(C2H4NH3)3N]2·(ZrF7)2·9H2O

Tren amine cations [(C₂H₄NH₃)₃N]³⁺ and zirconate or tantalate anions adopt a ternary symmetry in two hydrates, [H₃tren]₂·(ZrF₇)₂·9H₂O and [H₃tren]₆·(ZrF₇)₂·(TaOF₆)₄·3H₂O, which crystallise in R32 space group with a_H = 8.871 (2) Å, c_H = 38.16 (1) Å and a_H = 8.758 (2) Å, c_H = 30.112 (9) Å, respectively. Similar [H₃tren]₂·(MX₇)₂·H₂O (M = Zr, Ta; X = F, O) sheets are found in both structures; they are separated by a water layer (O_w(2)-O_w(3)) in [H₃tren]₂·(ZrF₇)₂·9H₂O. Dehydration of [H₃tren]₂·(ZrF₇)₂·9H₂O starts at room temperature and ends at 90 °C to give [H₃tren]₂·(ZrF₇)₂·H₂O. [H₃tren]₂·(ZrF₇)₂·H₂O layers remain probably unchanged during this dehydration and the existence of one intermediate [H₃tren]₂·(ZrF₇)₂·3H₂O hydrate is assumed. O_w(1) molecules are tightly hydrogen bonded with -NH₃⁺ groups and decomposition of [H₃tren]₂·(ZrF₇)₂·H₂O occurs from 210 °C to 500 °C to give successively [H₃tren]₂·(ZrF₆)·(Zr₂F₁₂) (285 °C), an intermediate unknown phase (320 °C) and ZrF₄.     

Analytical study of Joule heating effects on electrokinetic transportation in capillary electrophoresis

Electric fields are often used to transport fluids (by electroosmosis) and separate charged samples (by electrophoresis) in microfluidic devices. However, there exists inevitable Joule heating when electric currents are passing through electrolyte solutions. Joule heating not only increases the fluid temperature, but also produces temperature gradients in cross-stream and axial directions. These temperature effects make fluid properties non-uniform, and hence alter the applied electric potential field and the flow field. The mass species transport is also influenced. In this paper we develop an analytical model to study Joule heating effects on the transport of heat, electricity, momentum and mass species in capillary-based electrophoresis. Close-form formulae are derived for the temperature, applied electrical potential, velocity, and pressure fields at steady state, and the transient concentration field as well. Also available are the compact formulae for the electric current and the volume flow rate through the capillary. It is shown that, due to the thermal end effect, sharp temperature drops appear close to capillary ends, where sharp rises of electric field are required to meet the current continuity. In order to satisfy the mass continuity, pressure gradients have to be induced along the capillary. The resultant curved fluid velocity profile and the increase of molecular diffusion both contribute to the dispersion of samples. However, Joule heating effects enhance the sample transport velocity, reducing the analysis time in capillary electrophoretic separations.     

Platinum Nanoparticles Modified with Perfluorinated Alkylamines as a Model Cathode Catalyst for Fuel Cells

Platinum nanoparticles (NPs) modified with undecafluorohexylamine (UFHA) and octylamine were synthesized as a novel model cathode catalyst for fuel cells. The modified Pt NPs were well characterized by FTIR, X‐ray photoelectron spectroscopy, thermogravimetric analysis, and transmission electron microscopy. These NPs supported on carbon black were applied as electrocatalysts for the oxygen reduction reaction. The UFHA‐modified Pt NP catalyst showed high electrocatalytic activity and durability compared to a commercial catalyst. Besides suppression of undesired oxide formation on the Pt surface, the affinity between the perfluorinated alkyl chains of UFHA and Nafion^® improved the catalyst activity by creating a desirable proton conduction path. Additionally, UFHA modification improved durability by suppressing Pt dissolution and carbon corrosion because of restricted water accessibility. The β ‐oxide formation, which is responsible for Pt dissolution, was significantly attenuated by surface modification.     

Electrodeposition of nanostructured catalysts for electrochemical energy conversion: Current trends and innovative strategies

This review discusses the latest advances in electrodeposition of nanostructured catalysts for electrochemical energy conversion: fuel cells, water splitting, and carbon dioxide electroreduction. The method excels at preparing efficient and durable nanostructured materials, such as nanoparticles, single atom clusters, hierarchical bifunctional combinations of hydroxides, selenides, phosphides, and so on. Yet, in most cases, chemical composition cannot be decoupled from catalyst morphology. This compromises the rational design of electrodeposition procedures because performance indicators depend on both morphology and surface chemistry. We expect electrodeposition will keep unraveling its potential as the preferred method for electrocatalyst synthesis once a deeper understanding of the electrochemical growth process is combined with complex chemistries to have control of the morphology and the surface composition of complex (bifunctional) electrocatalysts.     

Characterization of the Insoluble Sludge from the Dissolution of Irradiated Fast Breeder Reactor Fuel

Insoluble sludge is generated in the reprocessing of spent fuel. The sludge obtained from the dissolution of irradiated fuel from the “Joyo” experimental fast reactor was analyzed to evaluate its chemical form. The sludge was collected by the filtration of the dissolved fuel solution, and then washed in nitric acid. The yields of the sludge weight were less than 1% of the total fuel weight. The chemical composition of the sludge was analyzed after decomposition by alkaline fusion. Molybdenum, technetium, ruthenium, rhodium, and palladium were found to be the main constituent elements of the sludge. X-ray diffraction patterns of the sludge were attributable to Mo₄Ru₄RhPd, regardless of the experimental conditions. The concentrations of molybdenum and zirconium in the dissolved fast reactor fuel solutions were low, indicating that zirconium molybdate hydrate is produced in negligible amounts in the process.     

Pd-Pt loaded graphene aerogel on nickel foam composite as binder-free anode for a direct glucose fuel cell unit

Fabrication of electrocatalyst for direct glucose fuel cell (DGFC) operation involves destructive preparation methods with the use of stabilizer like binder, which may cause activity depreciation. Binder-free electrocatalytic electrode becomes a possible solution to the above problem. Binder-free bimetallic Pd-Pt loaded graphene aerogel on nickel foam plates with different Pd/Pt ratios (1:2.32, 1:1.62, and 1:0.98) are successfully fabricated through a green one-step mild reduction process producing a Pd-Pt/GO/nickel form plate (NFP) composite. Anode with the binder-free electrocatalysts exhibit a strong activity in a batch type DGFC unit under room temperature. The effects of glucose and KOH concentrations, and the Pd/Pt ratios of the electrocatalyst on the DGFC performance are also studied. Maximum power density output of 1.25 mW cm⁻² is recorded with 0.5 M glucose/3 M KOH as the anodic fuel, and Pd₁Pt_0.98/GA/NFP as catalyst, which is the highest obtained so far among other types of electrocatalyst.     

BLEND MEMBRANES FOR DIRECT METHANOL AND PROTON EXCHANGE MEMBRANE FUEL CELLS

Sulphonated polystyrene ethylene butylene polystyrene(SPSEBS)prepared with 35%sulphonation was found to be highly elastic and enlarged up to 300%-400%of its initial length.It absorbed over 110%of water by weight.A major drawback of this membrane is its poor mechanical properties which are not adequate for use as polymer electrolytes in fuel cells.To overcome this,SPSEBS was blended with poly(vinylidene fluoride)(PVDF),a hydrophobic polymer.The blend membranes showed better mechanical properties than the base polymer.The effect of PVDF content on water uptake,ion exchange capacity and proton conductivity of the blend membranes was investigated.This paper presents the results of recent studies applied to develop an optimized in-house membrane electrode assembly(MEA)preparation technique combining catalyst ink spraying and assembly hot pressing.Easy steps were chosen in this preparation technique in order to simplify the method,aiming at cost reduction.The open circuit voltage for the cell with SPSEBS is 0.980 V which is higher compared to that of the cell with Nafion 117(0.790 V).From this study,it is concluded that a polymer electrolyte membrane suitable for proton exchange membrane fuel cell(PEMFC)and direct methanol fuel cell(DMFC)application can be obtained by blending SPSEBS and PVDF in appropriate proportions.The methanol permeability and selectivity showed a strong influence on DMFC performance.     

High-speed deposition of RE123 film with large current capacity by hot-wall type PLD system

We have studied a hot-wall heating system to produce GdBa₂Cu₃O_y (GdBCO) films with large critical currents (I_c) at a high production rate by a pulsed-laser-deposition (PLD) method. GdBCO films fabricated at a production rate of 30 m/h under the optimized conditions, especially a distance of 95 mm between the target and the substrate (T–S), exhibited high critical current densities (J_c) of about 3 MA/cm² and I_c over 300 A at a thickness of 1–2 μm. Furthermore, long GdBCO tapes prepared by repeated depositions at each tape-passing speed of 80 m/h showed uniform I_c distribution along the longitudinal direction, because the hot-wall system enabled to stabilize temperature within a few degrees at 800 °C. A 170 m long tape with I_c over 600 A was successfully fabricated at a production rate of 16 m/h using a laser power of 360 W.