Foam Separation of Stannous Ion from Aqueous Solution

Sn(II) was removed from solution using various foam separation techniques. It was found that Sn(II) could be effectively removed by adsorbing colloid flotation using either Fe(OH)₃ or Al(OH)₃ as the adsorbing colloid. Over 99% of the Sn(II) was removed from a solution initially containing 50 ppm Sn(II).     

Properties of foam films stabilized with tetraethylammonium perfluorooctane-sulfonate

Properties of single foam films prepared with tetraethylammonium perfluorooctane-sulfonate (TAPOS) were studied. Film thickness was measured as a function of NH₄Cl concentration in the film forming solution. The dependence of the film disjoining pressure versus the film thickness (disjoining pressure isotherms) and the mean lifetime of the films were studied. The dependence of the film thickness on the electrolyte concentration showed the presence of an electrostatic double layer at the film surfaces. The electrostatic double layer component of the disjoining pressure was screened at a NH₄Cl concentration higher than 0.2 M where Newton black films (NBFs) of 6 nm thickness were formed. These films are bilayers of amphiphile molecules and contain almost no free water. The disjoining pressure isotherms of the foam films formed with 0.001 M TAPOS were measured at two different NH₄Cl concentrations (0.005 and 0.0005 M). The Deryaguin-Landau-Verwey-Overbeek (DLVO) theory describes well the isotherms with an electrostatic double layer potential of ∼140 mV. The mean lifetime, a measure of the stability of the NBFs, was measured depending on surfactant concentrations. The observation of NBF was possible above a minimum TAPOS concentration of 9.4 × 10⁻⁵ M. Above this concentration, the lifetime increases exponentially. The dependence of the film lifetime on surfactant concentration is explained by the theory for NBF-rupture by nucleation mechanism of formation of microscopic holes.     

Surfactant accumulation within the top foam layer due to rupture of external foam films

The analysis of processes taking place in a steady pneumatic (dynamic) foam shows the possibility of different modes of surfactant accumulation within the top layers of bubbles due to rupture of external foam films. An increasing surfactant concentration within the top layers promotes the stabilisation of bubbles and the foam as a whole. Considering the balance of surfactant and water during the bursting of films it is possible to estimate the accumulated surfactant loss caused by a downwards flow through the Plateau borders of the subsurface bubble layer. This effect depends on the particular conditions, especially on the surfactant activity and concentration of the surfactant, water volume fraction in the foam and size of foam bubbles. The process of surfactant accumulation in the top foam bubble layer can be complicated due to the removal of part of the accumulated surfactant through transport with droplets spread out during bubble bursting.     

Film junction effect on foam drainage

Foam drainage is modelled by the flow of liquid through Plateau borders (PBs) that are the liquid channels resulting from the merging of three liquid films separating the gas bubbles. Available models generally neglect the influence of these films. Yet, within drainage conditions, experimental observations indicate a strong coupling of these films with the channels. We consider the influence of films on foam drainage through their effect on the cross-section geometry of the channels. More precisely, we assume that the Plateau border cross-section is enclosed by three circular arcs that are not always tangent but instead exhibit a non-zero contact angle θ as it has been observed experimentally. The liquid flow through the channels is studied using numerical simulations whose parameters are θ and the Boussinesq number, Bo, that reflects the surface shear viscosity of the interface. We show that, for values of Bo relevant for foam drainage conditions, a slight increase of θ results in a strong decrease of the average liquid velocity.     

Effect of protein aggregates on foaming properties of β-lactoglobulin

Our paper aims at determining the respective part of protein aggregates and non-aggregated proteins in the foam formation and stability of β-lactoglobulin. We report results on fractal aggregates formed at neutral pH and strong ionic strength (aggregates size from 30 to 190 nm). Pure aggregates and mixtures of non-aggregated/aggregated proteins at varying ratios were used. The capacity of aggregates to form and stabilize foams has been studied in relation with their ability to absorb at air/water interfaces. Our results show that protein aggregates are not able by themselves to improve the foaming properties but participate to a better foam stabilization in the presence of non-aggregated proteins. Non-aggregated proteins appear to be necessary to produce stable foams. We have shown that the amount and the size of aggregates had an influence on the drainage rate.     

The photocatalytic activity of TiO2 foam and surface modified binary oxide titania nanoparticles

Surface modified titania dioxide composite nanoparticles prepared by hydrogen reduction reaction and a mesoporous TiO₂ foam made from a surface modifier and a long chain organic surfactant were characterized by diffractive, spectroscopic and microscopic techniques and studied for their catalytic activity towards the decomposition of an industrial water pollutant, methyl orange. The surface deposition of ruthenium and silicon particles improved the photocatalytic activity of the composite particles resulting in a faster decomposition of the methyl orange compared to commercial TiO₂ alone. Modification of TiO₂ with RuO₂ only offered a marginal benefit over TiO₂ while the incorporation of RuO₂ and SiO₂ into TiO₂ resulted in a marked increase in the rate constant and catalytic activity. These results are consistent with the enhanced surface properties of the composite materials resulting from the modification of TiO₂ with RuO₂ and SiO_2. This surface enhancement effects appear synergetic to the charge separation process and hence the photocatalytic results are explained on the basis of a mechanism involving efficient charge transfer across the interfaces of the composites involving photogenerated electron–hole pairs. Results obtained in this study show that the percentage degradation after 1 h of illumination was 47.15% for TiO₂ foam, 75.5 and 106.4%, respectively, for TiO₂/RuO₂ (SiO₂ 5%, w/w) and TiO₂/RuO₂(SiO₂ 10%, w/w) and 34.15% for commercial TiO₂.     

泡塑负载巯基碳粉分离富集钯的研究及其方法应用

本文使用自制的负载有巯基碳粉的泡塑分离富集钯。试验了该富集到对钯的最佳吸附与解脱条件以及２３种共存离子的影响。对低钯管理样进行加标回收实验，结果表明，钯的平均回收率为８９．６５％，ＲＳＤ＝３．７１％。     

开孔泡沫塑料率相关的拉伸力学性能及本构关系

以Ｌｅｄｅｒｍａｎ的工作为基础，通过假设基体材料服从Ｖｏｉｇｔ体描述的粘弹性本构关系，导出了开孔泡沫塑料受拉伸的率相关本构关系；在此基础上研究了泡沫塑料力学性质同应变、应变率和结构参数的关系．     

Influence of Foam Apparent Viscosity and Viscoelasticity of Liquid Films on Foam Stability

The objective of this research work was to study the relationship among the apparent viscosity of bulk foam, the viscoelasticity of liquid films, and foam stability. Bulk foam tests showed that the drainage half-life of AOS foam was higher than that of sodium dodecyl sulfate (SDS) and hexadecyltrimethyl ammonium bromide (CTAB) foams. The results of foam apparent viscosity revealed that the foam apparent viscosity was related to foam quality rather than foam stability. Higher film viscoelasticity modulus could be assigned for α -olefin sulfonate (AOS) films than those for SDS and CTAB ones. The film conductivity tests indicated that AOS liquid films, compared with SDS and CTAB liquid films, could delay the liquid drainage speed under dynamic conditions. Compared with foam apparent viscosity, the viscoelasticity of liquid films appeared to be a key factor in foam stability.     

Supercritical CO<Subscript>2</Subscript> assisted preparation of open-cell foams of linear low-density polyethylene and linear low-density polyethylene/carbon nanotube composites

The open-cell structure foams of linear low-density polyethylene (LLDPE) and linear low-density polyethylene (LLDPE)/multi-wall carbon nanotubes (MWCNTs) composites are prepared by using supercritical carbon dioxide (sc-CO₂) as a foaming agent. The effects of processing parameters (foaming temperature, saturation pressure, and depressurization rate) and the addition of MWCNTs on the evolution of cell opening are studied systematically. For LLDPE foaming, the foaming temperature and saturation pressure are two key factors for preparing open-cell foams. An increase in temperature and pressure promotes both the cell wall thinning and cell rupture, because a high temperature results in a decrease in the viscosity of the polymer, and a high pressure leads to a larger amount of cell nucleation. Moreover, for the given temperature and pressure, the high pressurization rate results in a high pressure gradient, favoring cell rupture. For LLDPE/MWCNTs foaming, the addition of MWCNTs not only promotes the cell heterogeneous nucleation, but also prevents the cell collapse during cell opening, which is critical to achieve the open-cell structures with small cell size and high cell density.