有机薄膜器件负电阻特性的影响因素

研究了影响有机染料掺杂聚合物薄膜器件负电阻特性的因素，为探索有机负电阻的机理提供实验依据。实验中制备了多种有机染料掺杂聚合物薄膜器件，研究了有机小分子染料、聚合物基体、薄膜组成及厚度、ITO和聚苯胺阳极等对有机染料掺杂聚合物薄膜器件负电阻特性的影响。在室温、大气环境下，所制备的多种有机染料掺杂聚合物器件在所加电压为3～4V时，观察到明显的负电阻特性，电流峰谷比最大约为8。负电阻现象及峰谷比的大小受膜厚和器件的结构、制备工艺等影响。提出用负电阻和二极管并联组成的等效电路模型解释影响负电阻特性的因素，认为负电阻特性与载流子的不平衡注入有关。在此基础上设计、合成了主链含唔二唑电子传输基团的可溶性聚对苯撑乙烯衍生物，该聚合物兼具空穴和电子传输功能，在空气中具有较稳定的N型负电阻特性。进一步控制相关材料和工艺条件，有可能得到易于控制的负阻效应，开发出新型的有机负电阻器件。     

Stable marker-particle method for the Voronoi diagram in a flow field

The Voronoi diagram in a flow field is a tessellation of water surface into regions according to the nearest island in the sense of a “boat-sail distance”, which is a mathematical model of the shortest time for a boat to move from one point to another against the flow of water. The computation of the diagram is not easy, because the equi-distance curves have singularities. To overcome the difficulty, this paper derives a new system of equations that describes the motion of a particle along the shortest path starting at a given point on the boundary of an island, and thus gives a new variant of the marker-particle method. In the proposed method, each particle can be traced independently, and hence the computation can be done stably even though the equi-distance curves have singular points.     

Characterization of ceramic PVD thin films on AZ31 magnesium alloys

Ceramic thin films have been widely used to protect the metal substrate as coatings in the past years. In order to improve the poor corrosion resistance of AZ31 magnesium alloy, the study in this paper used the electron beam evaporation method to prepare ceramic PVD films on its surface with TiO₂ and Al₂O₃ as donors, respectively. Atomic force microscopy (AFM), scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), Auger electron spectroscopy (AES) and X-ray diffraction (XRD) were used to investigate the surface morphology, composition and microstructure of the thin films. Both films deposited on AZ31 took on compact top surface morphologies and grew as amorphous structures on substrate. AES test not only showed that films compositions deviated the standard stoichiometric ratios, but also found that element Mg diffused into films and existed as magnesium oxide in the TiO_x film as well as the AlO_x film. In the electrochemical corrosion test, the AlO_x coating on AZ31 exhibited the largest electrochemical impedance in a 3.5% NaCl solution. But it did not show better corrosion resistance than others for the poorer adhesion. Even if its thickness was small, the TiO_x coating on AZ31 exhibited the best corrosion resistance in this study. According to the observation and analysis, the damage of these films on AZ31 in aggressive solutions was mainly due to the existence of pores, microcracks, vacancies and poor adhesion between coating and substrate.     

Determination of gold in ore by flame atomic absorption spectrometry with flow-injection on-line sorbent extraction preconcentration

Gold in ores was determined by flame atomic absorption spectrometry following on-line preconcentration by sorbent extraction in a flow-injection system. The medium polarity adsorption resin Amberlite XAD-8 packed in a 220-μl micro-column was used to collect gold(III) from hydrochloric acid sample solutions for 40 s at 7.6 ml/min. Ethanol was used to elute the adsorbed analytes into the nebulizer. Optimization studies were made on sample loading rate, elution rate and sample acidity. Some possible interferences on the determination are discussed. A 35-fold enrichment was achieved at a sampling frequency of 60 h^?1 and with an RSD of 1.4%. The detection limit (3σ) and 2 μg l^?1. Results for gold in ore samples showed good agreement with those obtained using activated carbon adsorption preconcentration. The recoveries were 97–108%.     

低电阻测量设计实验中电位差计指针不稳的解决方法

本文分析了J33Q型电位差计在实验中指针不稳的原因,并提出了解决的办法。     

替代法测量微安表内阻的不确定度分析

在测量微安表内阻的众多方法中,替代法是最简单的方法。本文全面分析了影响测量结果不确定度的因素,求出了实验测量的最佳条件,计算了普通仪器组合下测量结果的相对不确定度。     

离心泵快速启动过程外部特性的试验研究

介绍离心泵快速启动试验装置和试验方法,对一台出口直径为80 mm的小型管道离心泵进行试验研究,分别测试了试验泵的稳态性能和各项瞬态性能,比较分析了两者的区别。结果显示,启动过程中,离心泵的扬程紧跟转速到达最大值,转速稳定后的瞬态性能与稳态假设对应,流量和扬程的上升历程与管路阻力特性直接相关,而转速与其基本无关; 在启动初始阶段,无量纲扬程呈现很大值,继而迅速减小到低于稳态假设值,表现出明显的瞬态效应。     

Continuous peeling extrusion of SEBS block copolymers

During continuous peeling, a central polymer rod free of visible defects was continuously extruded while being peeled at the die exit. Continuous peeling can occur at flow rates orders of magnitude higher than those at which initial surface cracking is observed. Thus, if continuous peeling can be controlled it may have potential industrial applications. The aim of this work was to study how different extrusion parameters (temperature, flow rate, die length and diameter) affect the presence of continuous peeling. The melt exiting the die has been filmed to link physical measurements and observations and to determine whether or not continuous peeling is present. Different criteria have been considered to represent the extrusion conditions under which continuous peeling may occur. Surface tension criteria can be used to try to predict the appearance and disappearance of continuous peeling. A correlation formula is also proposed for the rod diameter in terms of surface tension. Our results show that the ratio of the rod diameter to the die diameter is approximately 25% greater in the case of short-orifice dies (L/D ≈ 0) than for long capillaries (L/D ≈ 10). The correlations obtained allow analysis and discussion of flow regimes for possible applications.     

High temperature superconducting thin films for microwave filters

YBa₂Cu₃O_7-δ and Tl₂Ba₂CaCu₂O₈ thin films for microwave filters were synthesized by pulsed laser deposition and the two-step thalliation process. Substrate quality requirements and the relation of thin film morphology, microstructure with microwave surface resistance were discussed.     

Synthesis and copolymerization of new phosphorus‐containing acrylates

Two phosphorus‐containing acrylate monomers were synthesized from the reaction of ethyl α‐chloromethyl acrylate and t‐butyl α‐bromomethyl acrylate with triethyl phosphite. The selective hydrolysis of the ethyl ester monomer with trimethylsilyl bromide (TMSBr) gave a phosphonic acid monomer. The attempted bulk polymerizations of the monomers at 57–60 °C with 2,2′‐azobisisobutyronitrile (AIBN) were unsuccessful; however, the monomers were copolymerized with methyl methacrylate (MMA) in bulk at 60 °C with AIBN. The resulting copolymers produced chars on burning, showing potential as flame‐retardant materials. Additionally, α‐(chloromethyl)acryloyl chloride (CMAC) was reacted with diethyl (hydroxymethyl)phosphonate to obtain a new monomer with identical ester and ether moieties. This monomer was hydrolyzed with TMSBr, homopolymerized, and copolymerized with MMA. The thermal stabilities of the copolymers increased with increasing amounts of the phosphonate monomer in the copolymers. A new route to highly reactive phosphorus‐containing acrylate monomers was developed. A new derivative of CMAC with mixed ester and ether groups was synthesized by substitution, first with diethyl (hydroxymethyl)phosphonate and then with sodium acetate. This monomer showed the highest reactivity and gave a crosslinked polymer. The incorporation of an ester group increased the rate of polymerization. The relative reactivities of the synthesized monomers in photopolymerizations were determined and compared with those of the other phosphorous‐containing acrylate monomers. Changing the monomer structure allowed control of the polymerization reactivity so that new phosphorus‐containing polymers with desirable properties could be obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2207–2217, 2003