Flow Injection Chemiluminescence for the Determination of Estriol via a Noncompetitive Enzyme Immunoassay

A novel approach to the detection of estriol using a flow injection system coupled to enhanced chemiluminescent immunoassay was developed based on noncompetitive immunoassay formats. A conjugated estriol-ovalbumin immobilized immunoaffinity column was inserted into the flow system to trap the unbound horseradish peroxidase (HRP)-labeled antibody after an off-line incubation of estriol and HRP-labeled anti-estriol antibody. The trapped enzyme conjugate was detected by the injection of chemiluminescent substrates to produce enhanced chemiluminescence. The linear range for the determination of estriol is 10.0 to 400 ng · mL⁻¹ with a correlation coefficient of 0.996 and a detection limit of 5.0 ng · mL⁻¹. The total time for sampling and chemiluminescent detection of one sample is 400 seconds after 30 min of pre-incubation. The results for pregnancy serum samples obtained by this method are in good agreement with those obtained using ELISA.     

Trace lead measurement and on-line removal of matrix interference in seawater by isotope dilution coupled with flow injection and ICP-MS

Isotope dilution analysis method coupled with flow injection and inductively coupled plasma mass spectrometry (ID-FI-ICP-MS), enabled trace lead concentration in seawater to be determined and the high salt concentration in the matrix, such as Na⁺, Ca²⁺ and Mg²⁺, to be removed on-line. The operational parameters of the FI system including pH for the chelating reaction, concentration of 8-hydroxyquinoline-5-sulfonic acid (8-HQS), sample loading time and injection speed, washing time and speed, eluting acid concentration and eluting speed, and instrumental parameters for ICP-MS were optimized and selected. Accurate results could be achieved because the isotope ratios required can be precisely measured in the range of the eluting peak by means of ID-FI-ICP-MS. The 3σ detection limit was 0.204 ng ml⁻¹. The trace lead concentration of seawater in south Xiamen, China was 0.988 ± 0.039 ng ml⁻¹. The recoveries of spiked Pb standard in seawater and standard reference water (GBW 08607) were 97.9 and 101.0%, respectively, with a relative standard deviation of 0.98%. This method can be used to determine trace lead concentration in high salt matrix samples, and is especially useful when the eluting peaks do not have a Gaussian-distribution.     

Gas diffusion-flow injection determination of total inorganic carbon in water using tungsten oxide electrode

A novel gas diffusion-flow injection method has been developed for the rapid and sensitive determination of total inorganic carbon (TIC) in water. The method is based on the diffusion of CO₂ across gas permeable membrane from a donor stream containing 0.1 M HCl to an acceptor stream of sodium acetate (10⁻⁵ mol l⁻¹ and pH 10). The CO₂ trapped in the acceptor stream passes through an electrochemical flow cell contains a tungsten oxide wire and a silver/silver chloride electrode, where it was sensitively detected. The parameters affecting the sensitivity of the electrode such as buffer concentration, pH, flow rate and injected volume were studied in detail. The electrode response was linear in the concentration range from 5 to 100 μg ml⁻¹ CO₃²⁻ with a correlation coefficient (R²) of 0.998. Precision (R.S.D.) was 1.42% for 20 μg ml⁻¹ standard solution of CO₃²⁻ (n=10). The detection limit was 0.20 μg ml⁻¹ CO₃²⁻. The method was evaluated by the injection of real natural water samples and an average recovery of 100.1% was obtained. The sampling rate was 30 samples h⁻¹. The method is simple, feasible with satisfactory accuracy and precision and thus could be used for monitoring TIC in water.     

Exploiting flow injection and sequential injection anodic stripping voltammetric systems for simultaneous determination of some metals

Flow injection (FI) and sequential injection (SI) systems with anodic stripping voltammetric detection have been exploited for simultaneous determination of some metals. A pre-plated mercury film on a glassy carbon disc electrode was used as a working electrode in both systems. The same film can be repeatedly applied for at least 50 analysis cycles, thus reducing the mercury consumption and waste. A single line FI voltammetric system using an acetate buffer as a carrier and an electrolyte solution was employed. An injected standard/sample zone was mixed with the buffer in a mixing coil before entering a flow cell. Metal ions were deposited on the working electrode by applying a potential of −1.1 V vs Ag/AgCl reference electrode. The stripping was performed by anodically scanning potential of working electrode to +0.25 V, resulting a voltammogram. Effects of acetate buffer concentration, flow rate and sample volume were investigated. Under the selected condition, detection limits of 1 μg l⁻¹ for Cd(II), 18 μg l⁻¹ for Cu(II), 2 μg l⁻¹ for Pb(II) and 17 μg l⁻¹ for Zn(II) with precisions of 2–5% (n=11) were obtained. The SI voltammetric system was similar to the FI system and using an acetate buffer as a carrier solution. The SI system was operated by a PC via in-house written software and employing an autotitrator as a syringe pump. Standard/sample was aspirated and the zone was then sent to a flow cell for measurement. Detection limits for Cd(II), Cu(II), Pb(II) and Zn(II) were 6, 3, 10 and 470 μg l⁻¹, respectively. Applications to water samples were demonstrated. A homemade UV-digester was used for removing organic matters in the wastewater samples prior to analysis by the proposed voltammetric systems.     

Flow‐Injection Amperometric Detection with Solvent Polymeric Membrane Ion Sensors

An amperometric detector for hydrophobic ions based on a plasticized poly(vinyl) chloride (PVC) membrane incorporated in a flow‐injection system was developed. A four‐electrode potentiostat with ohmic drop compensation was used, while a flow‐through cell incorporated the four electrodes and the membrane, which contained tetrabutylammonium tetraphenylborate. When the influence of the applied potential and of the flow‐injection variables on the determination of tetrabutylammonium was studied, a linear relationship was observed between current peak height and ion concentration over a range of 5×10^?6–6×10^?5 M tetrabutylammonium. Good repeatability and between‐day reproducibility and high sample frequency were obtained. The effect of other ions was studied. Two different amperometric methods, indirect and direct, were also developed for the determination of dodecylsulfate in the concentration range 3×10^?5–9×10^?4 M.     

Utility of copper(II) oxide as a packed reactor in flow injection assembly for rapid analysis of some angiotensin converting enzyme inhibitors

A new simple, sensitive, rapid and precise flow injection (FI) procedure based on the formation of copper complexes with some angiotensin converting enzyme (ACE) inhibitors has been developed and evaluated for the analysis of lisinopril (LN), enalapril maleate (EP), ramipril (RP) and perindopril tert-butylamine (PD). In this method, samples were injected into a flowing stream of distilled-deionized water, carried through the packed reactor of CuO for derivatization followed by ultraviolet (UV) detection. The flow rate was 1.5 ml min⁻¹ and column temperature was ambient (25 °C). Lisinopril was injected directly into the flowing stream and the detector response was measured at 262 nm. The hydrolysis products of enalapril maleate, ramipril and perindopril tert-butylamine in 0.2N NaOH were injected after neutralization with 1N HCl and the detector response was measured at 272, 265 and 252 nm, respectively. The developed method was successfully applied to the determination of tested drugs in pharmaceutical preparations at a sampling rate of 60 samples h⁻¹ and a recovery near 100% for all compounds.     

Determination of iodide by detection of iodine using gas-diffusion flow injection and chemiluminescence

This work describes development of a flow injection (FI) system for determination of iodide, based on the chemiluminescence (CL) reaction between iodine and luminol. Iodide in the sample zone is oxidized to iodine. Employment of a gas-diffusion (GD) unit allows for selective detection of the generated CL (425 nm). Preliminary results showed for concentrations of less than 2 mg L⁻¹, that signals were irreproducible and that the calibration was not linear.In order to solve these problems, a method of ‘membrane conditioning’ was investigated, in which iodide stream was continuously merged with oxidant to generate I₂ that conditioned the GD membrane and tubing. This minimized surface interaction between the active surface and the I₂ generated from the samples, thus improving both precision and sensitivity. By employing membrane conditioning, it has been possible to reliably detect concentrations down to 0.1 mg L⁻¹.At the optimized condition, an excellent linear calibration (r² = 0.999) was obtained from 0.1 to 1.0 mg L⁻¹. The method was successfully applied to determine iodide in some pharmaceutical products such as potassium iodide tablets and a liquid patent medicine. However, for vitamin tablets, ascorbic acid was found to interfere seriously by causing a negative signal.     

流动注射区域采样法测定镀锌钝化液中高浓度锌

本文建立了流动注射二甲酚橙光度法测定镀锌纯化液中Ｚｎ￣２＋的自动分析方法。利用区域采样技术和调整管路参数自动完成对样品的上千倍稀释，确定了最佳分析条件并研究了干扰离子的影响及消除办法。所建方法仪器简单，分析速度为８４次／小时，变异系数（Ｚｎ￣２＋１６．０ｇ／Ｌ，ｎ＝２０）为１．Ｏ％，用于实际钝化液分析，相对误差小于±１０％。     

Flow-injection chemiluminescence determination of chloroquine using peroxynitrous acid as oxidant

A new flow-injection chemiluminescence (CL) method for determination of chloroquine is proposed based on a stronger chemiluminescence of chloroquine in hydrogen peroxide-nitrite-sulfuric acid medium. The proposed method allows the measurement of chloroquine over the range of 3.0×10⁻⁷ to 1.0×10⁻⁵ mol l⁻¹. The detection limit is 8.6×10⁻⁸ mol l⁻¹, and the relative standard deviation for 1.0×10⁻⁶ mol l⁻¹ chloroquine (n=11) is 1.6%. The CL mechanism is also discussed.