负载纳米银复合微球制备及其催化性能

以具有温度和pH双重敏感性能的N-异丙基丙烯酰胺(NIPAM)共聚丙烯酸(AA) P(NIPAM-co-AA)高分子微凝胶为模板, 以乙醇为还原剂, 原位还原得到负载纳米银的微米尺度Ag/P(NIPAM-co-AA)复合微凝胶材料. 通过扫描电子显微镜(SEM)、X射线衍射(XRD)仪和紫外-可见(UV-Vis)分光光度计等对复合材料的形貌、组成和催化性能进行表征. 研究结果表明, Ag/P(NIPAM-co-AA)复合微球具有均一的表面结构, 微凝胶的限域作用显著提高了纳米银的分散性和稳定性. 另外, Ag/P(NIPAM-co-AA)复合微球对对硝基苯酚(4-NP)的还原具有较好的催化活性, 且其催化活性与微凝胶网络结构的溶胀、收缩行为有一定关系, 即模板微凝胶的温敏特性可以实现对对硝基苯酚催化反应活性的调控作用.     

苯乙烯和N-乙烯基吡咯烷酮共聚物/Ag复合微球的制备及性能研究

首先用无皂乳液聚合法制备了单分散聚苯乙烯(PSt)乳液,以此为种子乳液,使用N,N-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,进行苯乙烯和N-乙烯基吡咯烷酮(NVP)共聚合制备了以PSt为核、St和NVP共聚物为壳的具有核-壳结构的聚合物微球(P(St-NVP)).以此微球为模板通过化学沉积法得到了粒径分布均匀、单分散的P(St-NVP)/Ag复合微球.傅里叶红外光谱、X-射线衍射、扫描电镜、透射电镜、激光粒度仪和紫外-可见光谱对复合微球的结构、形貌、物相及催化性能进行了表征.结果表明,P(St-NVP)/Ag复合微球具有规则的球形结构,粒径在400～700 nm之间,随交联剂浓度或种子乳液浓度的增加,复合微球粒径减小.粒径在十几个纳米左右的银粒子均匀分布在微球表面和内部.载银复合微球在NaBH4还原4-硝基苯酚为4-氨基苯酚的模型反应中表现出较高的催化活性.     

聚乳酸/氧化锌柱撑皂石纳米复合材料制备与性能及结构表征

通过微波水解法制备了ZnO柱撑皂石,并以其为加工助剂制备了聚乳酸(PLA)/ZnO柱撑皂石纳米复合材料.通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、对ZnO柱撑皂石及PLA/ZnO柱撑皂石纳米复合材料的结构进行了表征,并对其力学性能和热稳定性能进行了测试.微观结构分析表明,ZnO柱撑皂石呈现剥离状,并均匀分散在PLA基质中.力学性能研究表明0.3%ZnO柱撑皂石的加入有助于改善PLA复合材料的断裂伸长率.SEM分析表明PLA复合材料的断面发生明显改变,表现良好韧性;DSC结果显示纳米ZnO柱撑皂石可以降低复合材料的玻璃化转变温度、结晶温度,有助于提高PLA复合材料的结晶度,与XRD分析相吻合;热重分析表明ZnO柱撑皂石可以提高PLA复合材料的热稳定性.测试结果表明,ZnO柱撑皂石在PLA基质中起到了异相成核的作用,促进了PLA基质的结晶.     

基于电纺丝法的In2O3/CdO复合材料的制备及甲醛气敏特性

用静电纺丝法制备了In(NO₃)₃/聚乙烯吡咯烷酮(PVP)纺丝前驱物, 然后分别在500、600、700℃时烧结得到三种In₂O₃ 纳米纤维. 通过X 射线衍射(XRD)仪、热重差热分析(TG/DTA)、场发射扫描式电子显微镜(FE-SEM)表征结果得知, 500℃时In₂O₃的晶相已经形成, 且粒径为最小, 约为24 nm, 纳米纤维呈介孔结构.将三种烧结温度的In₂O₃纤维制作成气敏元件, 测试对比了三种元件对甲醛气体的敏感特性, 结果表明, 500℃烧结得到的In₂O₃纳米纤维在工作温度为240℃时响应最好, 对浓度为10×10^-6 (体积分数, φ)甲醛的响应为7.用静电纺丝法合成了CdO 纳米颗粒, 通过XRD、SEM 表征得知CdO 呈粒径约为68 nm 的颗粒. 将In₂O₃和CdO以不同摩尔比(1:1, 10:1, 20:1)复合, 对比测试了纯In₂O₃及三种In₂O₃/CdO复合材料对应的气敏元件对甲醛的气敏特性, 测试结果表明当In₂O₃纳米纤维与CdO纳米颗粒以摩尔比10:1 复合时, 元件的工作温度较低(200℃), 且对甲醛表现出最佳的气敏特性, 对浓度为10×10^-6甲醛的响应为13.6, 响应/恢复时间为140 s/32s. 最后对不同摩尔比复合的In₂O₃/CdO对甲醛的气敏机理进行了初步分析.     

纳米储能纤维复合过滤膜的制备及性能

以静电纺丝技术制备的同轴聚甲基丙烯酸十八烷基酯(PSMA)/聚对苯二甲酸乙二酯(PET)纳米储能纤维为支撑层,经聚偏氟乙烯(PVDF)涂覆成膜和溶剂化处理,制备了一种低压高水通量的纳米储能纤维复合过滤膜(NFCM),其中以水或乙醇为凝固溶液的复合过滤膜分别记为NFCM@H2O或NFCM@EtOH.分析并讨论了不同溶剂处理方式对NFCM力学性能和表面形貌的影响,表征了膜的纯水通量和抗污性能,用扫描电子显微镜(SEM)观察了膜的横断面形貌.结果表明,PSMA/PET纳米储能纤维具有明显的吸放热行为,熔融温度和热焓值分别为36.5℃和10.7J/g,NFCM的熔融温度和热焓值分别为36℃和2.7J/g.NFCM的形貌结构、纯水通量和截留率与溶剂处理方式相关,NFCM@EtOH膜的水通量介于100~1400L/(m2·h)之间,而NFCM@H2O膜的水通量仅在40~220L/(m2·h)之间.NFCM的拉伸强度由初始0.925MPa(PVDF)提高到4.28MPa以上.NFCM中的相变材料对膜过滤性能有重要影响,并在过滤温度低于50℃时具有减缓作用.     

Polyvinylimidazole/sol–gel composite as a novel solid‐phase microextraction coating for the determination of halogenated benzenes from aqueous solutions

A polyvinylimidazole/sol–gel composite is proposed as a novel solid‐phase microextraction fiber to extract five halobenzenes from the headspace of aqueous solutions in combination with gas chromatography with mass spectrometry. The prepared fiber was characterized by scanning electron microscopy and Fourier transform infrared spectroscopy. The obtained results showed that porous polyvinylimidazole/sol–gel composite was chemically deposited on fused silica fiber. The effect of important extraction parameters including extraction temperature, extraction time, and salt content were investigated. The optimum conditions were as follows: extraction temperature 25°C, extraction time 20 min, and salt concentration 30 w/v%. Detection limits and relative standard deviations of the developed method for halogenated benzenes were below 0.1 pg/mL and 15%, respectively. Repeatability of the proposed method, explained by relative standard deviation, varied between 5.48 and 9.15% (n = 5). The limits of detection (S/N = 3) ranged between 0.01 and 0.10 ng/L using gas chromatography with mass spectrometry with selected ion monitoring mode. For real sample analysis, three types of water samples with different matrices (ground, surface, and tap water) were studied. The optimized procedure was applied to extraction and method validation of halogenated benzenes in spiked water samples.     

磁性复合材料在固相萃取食品中环境类雌激素的应用进展EI北大核心CSCD

环境类雌激素作为食品中一类典型的污染物,严重影响人体内分泌系统的功能与代谢。磁性固相萃取因其简洁高效、富集倍数高、适用范围广等优点,已被广泛应用于食品中环境类雌激素的富集检测。Fe_(3)O_(4)纳米粒子作为经典的磁固相萃取材料,易于形成大分子团聚物,影响其选择吸附性能,限制了磁固相萃取技术在食品中环境类雌激素的痕量分析。新兴的磁性复合材料可有效地解决上述问题,已成为磁固相萃取技术的研究热点之一。本文综述了近5年来新兴的磁性聚合物复合材料、磁性碳基复合材料和磁性金属-有机骨架复合材料在食品中环境类雌激素富集检测的应用进展。     

Ferrocene-modified dendrimers as support of copper nanoparticles: evaluation of the catalytic activity for the decomposition of ammonium perchlorate

Ferrocene (Fc)-based systems are frequently used as burning rate catalysts in the decomposition of ammonium perchlorate (AP)-based propellants. However, small Fc derivatives migrate to the surface of the propellant resulting in undesirable changes in the designed burning parameters and unstable combustion. To retard the migration and to increase the combustion rate of AP, fourth-generation polyamidoamine (PAMAM) dendrimers modified with Fc (PAMAM generation 4 [G4]-Fc) were synthetized and used as support for the obtention of copper nanoparticles (CuNPs). PAMAM G4 produced smaller nanoparticles (1–2 nm) with lower aggregation than PAMAM G4-Fc (12–14 nm). X-ray photoelectron spectroscopy (XPS) characterization confirmed the superior stabilizing and protecting effect against oxidation of CuNPs by PAMAM G4 in comparison to PAMAM G4-Fc, whereas molecular dynamics simulations have shown less flexibility and lower presence of stabilizing sites for nanoparticles in PAMAM G4-Fc. Antimigration tests confirmed the negligible migration of PAMAM G4-Fc compared with Fc, whereas PAMAM G4-Fc|CuNP affected the high-temperature decomposition of AP positively, decreasing the decomposition temperature in 87 °C owing to a synergistic effect between CuNPs and Fc. PAMAM G4-Fc can act both as an effective antimigration system of Fc and as a stabilizing framework of metal nanoparticles with application as catalysts of AP.     

One step nanoencapsulation of corrosion inhibitors for gradual release application

The direct application of corrosion inhibitors on metal surfaces is potentially dangerous for the environment and the restoration operators, thus new conservation strategies are mandatory. In this study, two copper corrosion inhibitors, 1H-benzotriazole (BTA) and 5-phenyl-1H-tetrazole (PT), are encapsulated in a silica nanocontainer, for future application in smart coatings, with the aim to reduce the amount of chemicals used in treatments, their dispersion in the environment and the direct exposure of the operators to these chemicals. In particular, composite silica nanocapsules, containing the corrosion inhibitors, are prepared via one-step synthesis, based on mini-emulsion polymerisation processes.The morphology, structure, and texture of these loaded silica nanocontainers are characterised by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and N₂ physisorption (BET/BJH). Micro-Raman spectroscopy (RS) is performed to characterise the composition. UV–visible spectroscopy and thermal analysis (TG/DSC) are performed for the loading and encapsulation efficiency (L%, EE%) study.Synthesised nanocapsules show a core-shell structure and, when loaded with the inhibitors, have size ranging from about 130 to 170 nm and a BET surface area of the order of 800 m²/g. The EE% is maximum in the case of BTA and decreases to ～52% in the case of PT.     

New polymer electrolyte membrane for medium-temperature fuel cell applications based on cross-linked polyimide Matrimid and hydrophobic protic ionic liquid

New hydrophobic protic ionic liquid, 2-butylaminoimidazolinium bis(trifluoromethylsulfonyl)imide (BAIM-TFSI), has been synthesized. The ionic liquid showed good thermal stability to at least 350 °C. The conductivity of BAIM-TFSI determined by electrochemical impedance method was found to be 5.6 × 10^?2 S/cm at 140 °C. Homogeneous composite films based on commercial polyimide (PI) Matrimid and BAIM-TFSI containing 30–60 wt% of ionic liquid were prepared by casting from methylene chloride solutions. Thermogravimetric analysis data indicated an excellent thermal stability of PI/BAIM-TFSI composites and thermal degradation points in the temperature range 377 °C–397 °C. The addition of ionic liquid up to 50 wt% in PI films does not lead to any significant deterioration of the tensile strength of the polymer. The dynamic mechanical analysis results indicated both an increase of storage modulus E′ of PI/BAIM-TFSI composites at room temperature and a significant E′ decrease with temperature compared with the neat polymer. The cross-linking of the PI with polyetheramine Jeffamine D-400 allowed to prepare PI/Jeffamine/BAIM-TFSI (50%) membrane with E′ value of 300 MPa at 130 °C. The ionic conductivity of this cross-linked composite membrane reached the level of 10^?2 S/cm at 130 °C, suggesting, therefore, its potential use in medium-temperature fuel cells operating in water-free conditions.