汶川地震断裂带岩脉矿物拉曼谱峰特征

对汶川地震断裂带深溪沟出露的基岩错动面两侧岩脉中的石英矿物进行了拉曼谱峰测定, 并根据所测石英的464 cm-1拉曼谱峰向高波数的偏移量估算了断裂带中的压应力分布。测试结果表明, 错动面附近岩脉中石英的464 cm-1拉曼谱峰向高波数偏移量为3.29 cm-1, 相应的压应力值为368.63 MPa, 明显低于错动面两侧应力积累, 这可能是由于错动面的多次活动导致了应力不断得到释放。断裂南东盘(下盘)远离错动面, 岩脉中石英的464 cm-1拉曼谱峰向高波数偏移量具有增加的趋势, 相应的应力积累也逐渐增强, 距错动面21 m处的石英样品的464 cm-1拉曼谱峰向高波数偏移4.40 cm-1, 相应压应力可达到494.77 MPa。剖面北西盘(上盘)在距错动面10 m处, 样品464 cm-1拉曼谱峰的偏移量达到最大值, 相应的应力积累为519.87 MPa, 其后远离错动面应力积累开始减弱, 在北西盘17 m处, 应力积累骤然下降至400.37 MPa。在西北盘距错动面27 m处, 岩脉石英的464 cm-1拉曼谱峰向高波数偏移量下降至3.21 cm-1, 应力已经减弱到359.59 MPa, 这可能是由于该处位于断裂带的边缘, 远离错动面, 受到了较小的断层活动的影响。因此, 汶川地震断裂带内的应力虽然得到部分释放, 但剩余的应力分布并不均匀, 而且在局部还存在较高的应力积累, 这反应了断裂带中岩石的力学性质在空间上具有不均匀性。     

多层膜劳厄透镜对8keV X射线的聚焦性能模拟研究

基于多层膜技术的劳厄(Laue)透镜能实现硬X射线纳米级聚焦,在X射线微纳分析领域具有重要的应用前景.基于衍射动力学理论,分析了X射线在多层膜劳厄透镜中的传播,计算了不同结构的多层膜劳厄透镜对8 keVX射线的聚焦性能.结果表明,最外层厚度为5 nm的倾斜多层膜劳厄透镜可获得5.7 nm的聚焦光斑和26%的平均衍射效率...     

Physical characterization of a new composition of oxidized zirconium-2.5 wt% niobium produced using a two step process for biomedical applications

Zirconium and particularly Zr-2.5 wt%Nb (Zr2.5Nb) alloy are useful for engineering bearing applications because they can be oxidized in air to form a hard surface ceramic. Oxidized zirconium (OxZr) due to its abrasion resistant ceramic surface and biocompatible substrate alloy has been used as a bearing surface in total joint arthroplasty for several years. OxZr is characterized by hard zirconium oxide (oxide) formed on Zr2.5Nb using one step thermal oxidation carried out in air. Because the oxide is only at the surface, the bulk material behaves like a metal, with high toughness. The oxide, furthermore, exhibits high adhesion to the substrate because of an oxygen-rich diffusion hardened zone (DHZ) interposing between the oxide and the substrate.In this study, we demonstrate a two step process that forms a thicker DHZ and thus increased depth of hardening than that can be obtained using a one step oxidation process. The first step is thermal oxidation in air and the second step is a heat treatment in vacuum. The second step drives oxygen from the oxide formed in the first step deeper into the substrate to form a thicker DHZ. During the process only a portion of the oxide is dissolved. This new composition (DHOxZr) has approximately 4-6 μm oxide similar to that of OxZr. The nano-hardness of the oxide is similar but the DHZ is approximately 10 times thicker. The stoichiometry of the oxide is similar and a secondary phase rich in oxygen is present through the entire thickness. Due to the increased depth of hardening, the critical load required for the onset of oxide cracking is approximately 1.6 times more than that of the oxide of OxZr. This new composition has a potential to be used as a bearing surface in applications where greater depth of hardening is required.     

Research on identifying the order of fringe pattern traces using angular scan and zone search method

A method for automatically identifying the order of fringe pattern traces is presented. It uses the simplified Otsu algorithm for obtaining the threshold, the angular scan in the range of 45~ for searching the trace positions, and the zone search technique for identifying different traces. Experimental results show that the proposed method may reliably obtain the order of fringe pattern traces orientating from almost 45° to 90°.     

Chiral Separation of Esmolol and Terazosin by Cyclodextrinmodified Capillary Zone Electrophoresis

IntroductionTheincreasingnecessity0fpharmacologicalresearchforchiraldrugshasrenderedchiralseparationanactiveareaincaPillaryelectroph0resis(CE)today.Variousmodes0fCE,includingcaPillaryzoneelectroph0resis(CZE),micellarelectrokineticchromatography(MEKC),caPillarygelelectrophoresis(CGE)andcapillaryisotachophoresis(CITP),havebeenappliedforthispurp0se',amongwhichCZEisthemostpopularoneforitshighefficiency,lowexpenseandeaseofoperation.Forsuccessfulchiralseparati0ninCZE,theselectortypeisofcr…     

高分辨率X射线显微成像及其进展

介绍了高分辨率X射线显微成像产生背景和发展过程，着重分析了基于光学元件波带片的放大成像的基本原理，并简述了高分辨率三维成像的有关理论。同时给出国内外高分辨率X射线显微成像研究的最新进展，展望了高分辨率X射线显微成像的应用前景。     

Analytical solution to a mode of mixed elastohydrodynamic lubrication with mixed contact regimes: Part I. Without consideration of contact adhering layer in the inlet zone

In 2005, Zhang presented a Grubin-like inlet zone analysis to the isothermal line contact elastohydrodynamic lubrication under relatively heavy loads when the hydrodynamic film thickness in the Hertzian zone approaches zero and the EHL fluid is Newtonian [Zhang, Y.B. A justification of the load-carrying capacity of elastohydrodynamic lubrication film based on the Newtonian fluid model. Industrial Lubrication and Tribology, 2005, Vol. 57, pp. 224–232]. His results showed that in this EHL, when the rolling speed is lower than the characteristic rolling speed (U_ch =) 0.0372W^1.50/G, the Hertzian zone is in physical adsorbed layer boundary lubrication while the inlet zone is in conventional hydrodynamic lubrication. This mode of EHL represents a mode of mixed EHL with mixed contact regimes, where hydrodynamic films with different rheological behaviors occur in different areas of the contact. The present paper presents an analysis to this mode of mixed EHL by using the Grubin type method when the contact adhering layer in the inlet zone is neglected. Pressures, film thicknesses and load partition in the contact are obtained from this analysis. It is also found that the formula for the characteristic rolling speed U_ch = 0.0372W^1.50/G obtained by Zhang [Zhang, Y.B. A justification of the load-carrying capacity of elastohydrodynamic lubrication film based on the Newtonian fluid model. Industrial Lubrication and Tribology, 2005, Vol. 57, pp. 224–232] may be valid for the dimensionless load W > 1.0E−7, while it may be invalid for the dimensionless load W < 1.0E−8. In part II [Zhang, Y.B. Analytical solution to a mode of mixed elastohydrodynamic lubrication with mixed contact regimes: Part II. Considering the contact adhering layer effect in the inlet zone. Journal of Molecular Liquids, 2006, Vol. 117. (doi:10.1016/j.molliq.2006.04.007)] will be presented an analysis to other two modes of mixed EHL with mixed contact regimes for relatively heavy loads, low rolling speeds and Newtonian fluids, where the conventional hydrodynamic lubrication, physical adsorbed layer boundary lubrication and oxidized chemical layer boundary lubrication can simultaneously occur in the inlet zone while the oxidized chemical layer boundary lubrication or the fresh metal-oxidized chemical boundary layer dry contact occur in the Hertzian zone, considering the contact adhering layer effect in the inlet zone.     

Identification of a fault zone ahead of the tunnel excavation face using the extended Kalman filter

Simulation of mechanized tunneling and on-site excavation require very good knowledge of the geomechanical and material properties. Identification of the material must be fast and continuously performed during tunnel excavation for the best possible strategies for advancing the tunnel boring machine. We present in this work the use of the extended Kalman filter (EKF) for identification of the inclined fault zone ahead of the face. The EKF showed fast and stable convergence of the model parameters under study. In comparison with the particle swarm optimization technique applied to the same back analysis problem, faster convergence of the identified parameters as well as high robustness with respect to the choice of the initial parameter values have been observed.     

Determination of ethyl glucuronide in human serum by capillary zone electrophoresis and an immunoassay

Ethyl glucuronide (EtG) is a marker of recent alcohol consumption. For the optimization of the analysis of EtG by CZE with indirect absorbance detection, the use of capillaries with permanent and dynamic wall coatings, the composition of the BGE, and various sample preparation procedures, including dilution with water, ultrafiltration, protein precipitation, and SPE, were investigated. Two validated screening assays for the determination of EtG in human serum, a CZE‐based approach and an enzyme immunoassay (EIA), are described. The CZE assay uses a coated capillary, 2,4‐dimethylglutaric acid as an internal standard, and a pH 4.65 BGE comprising 9 mM nicotinic acid, ε‐aminocaproic acid and 10% v/v ACN. Proteins are removed via precipitation with ACN prior to analysis and the LOQ is 0.50 mg/L. The EIA is based upon commercial reagents which are promoted for the determination of urinary EtG. Krebs–Ringer solution containing 5% BSA is used as a calibration matrix. All samples are ultrafiltered prior to analysis of the ultrafiltrate on a Mira Plus analyzer. Assay calibration ranged between 0 and 2 mg/L and the upper reference limit was determined to be 0.05 mg/L. Both assays proved to be suitable for the analysis of samples from different individuals. For EtG levels above 0.50 mg/L, good agreement was observed for the comparison of the results of the two methods.     

Separation of alkylbenzyl quaternary ammonium compounds by capillary zone electrophoresis with sample stacking injection

Summary A systematic investigation of operational buffer systems, sample preparation and instrument parameters for achieving the best possible performance for determinating an homologous series of N-benzyl-N-alkyl-N,N-dimethylammonium chloride compounds by capillary zone electrophoresis with direct UV detection. The most effective separation was achieved within 3.5 min with the addition of acetonitrile (40%) in a phosphate buffer (20 mM pH 5.2) using a 40 cm fused-silica capillary operating at 25 KV and 20°C. Degassing of all electrolyte solutions and samples was very important. The linearity and repeatability for each compounds were satisfactory. To improve detection limits, on-column sample preconcentration, sample stacking, was investigated achieving a tenfold enrichment factor and quantitation limits about 10⁻⁷M.