Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

Towards understanding the increase in strength of thermotropic polyesters with heat treatment

Thermotropic copolyester fibers of oxynaphthoate and oxybenzoate have been subjected to conditions that promote solid-state polymerization as well as annealing. The annealing process causes the crystals to perfect with a simultaneous increase in heat of fusion and melting temperature. Solid-state polymerization, a reaction rate-controlled process, causes the polymer viscosity average molecular weight to increase by chain extension from about 14,000 g/mole to more than 87,000 g/mole with a simultaneous impressive increase in tenacity from about 10 g/d (1.2 GPa) to almost 30 g/d (3.7 GPa). To understand the changes in mechanical properties, we have modeled the fiber structure as short rod-like molecules poorly bonded to a continuous matrix of parallel molecules. Lengthening of the reinforcing molecules facilitates better transfer of load from matrix to molecules, resulting in higher tenacity fibers. © 1994 John Wiley & Sons, Inc.     

On interrelation between the internal pressure and the cohesion energy density

The question about the definition of the “internal pressure” concept is being discussed. It is shown that the previously found differential relation between the cohesion energy density and the internal pressure is one of the examples of an absolutely general interrelation between definitely connected differential functions. It is ascertained that the ratio (the internal pressure divided by the cohesion energy density) is a structuresensitive parameter inherent to the calorific (thermal) equation of a liquid state.     

硼中子俘获治疗的蒙特卡罗方法模拟

用通用蒙特卡罗程序MCNP模拟了粒子在人脑中的输运过程. 吸收剂量率主要来自以下四个反应:¹⁰B(n,α)⁷Li,¹⁴N(n,p)¹⁴C,¹H(n,γ)²D,快中子弹性散射反应.对肿瘤区的贡献主要来自硼中子吸收反应.结果表明,超热中子比热中子适合于深肿瘤的治疗,而热中子对浅肿瘤的治疗有优越性,比如皮肤癌.同确定论方法的结果相比,蒙特卡罗方法不失为一种模拟中子俘获治疗的好工具.     

Synthesis and copolymerization of new phosphorus‐containing acrylates

Two phosphorus‐containing acrylate monomers were synthesized from the reaction of ethyl α‐chloromethyl acrylate and t‐butyl α‐bromomethyl acrylate with triethyl phosphite. The selective hydrolysis of the ethyl ester monomer with trimethylsilyl bromide (TMSBr) gave a phosphonic acid monomer. The attempted bulk polymerizations of the monomers at 57–60 °C with 2,2′‐azobisisobutyronitrile (AIBN) were unsuccessful; however, the monomers were copolymerized with methyl methacrylate (MMA) in bulk at 60 °C with AIBN. The resulting copolymers produced chars on burning, showing potential as flame‐retardant materials. Additionally, α‐(chloromethyl)acryloyl chloride (CMAC) was reacted with diethyl (hydroxymethyl)phosphonate to obtain a new monomer with identical ester and ether moieties. This monomer was hydrolyzed with TMSBr, homopolymerized, and copolymerized with MMA. The thermal stabilities of the copolymers increased with increasing amounts of the phosphonate monomer in the copolymers. A new route to highly reactive phosphorus‐containing acrylate monomers was developed. A new derivative of CMAC with mixed ester and ether groups was synthesized by substitution, first with diethyl (hydroxymethyl)phosphonate and then with sodium acetate. This monomer showed the highest reactivity and gave a crosslinked polymer. The incorporation of an ester group increased the rate of polymerization. The relative reactivities of the synthesized monomers in photopolymerizations were determined and compared with those of the other phosphorous‐containing acrylate monomers. Changing the monomer structure allowed control of the polymerization reactivity so that new phosphorus‐containing polymers with desirable properties could be obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2207–2217, 2003     

Studies on thermal and morphological properties of 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane-epoxy-bismaleimide matrices

A new cyanate ester monomer, 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane has been synthesized and characterized. Epoxy modified with 4, 8 and 12% (by weight) of cyanate ester were made using epoxy resin and 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane and cured by using diaminodiphenylmethane. The cyanate ester modified epoxy matrix systems were further modified with 4, 8 and 12% (by weight) of bismaleimide (N,N′-bismaleimido-4,4′-diphenylmethane). The formation of oxazolidinone and isocyanurate during cure reaction of epoxy and cyanate ester blend was confirmed by IR spectral studies. Bismaleimide-cyanate ester-epoxy matrices were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and heat deflection temperature (HDT) analysis. Thermal studies indicate that the introduction of cyanate ester into epoxy resin improves the thermal degradation studies at the expense of glass transition temperature. Whereas the incorporation of bismaleimide into epoxy resin enhances the thermal properties according to its percentage content. However, the introduction of both cyanate ester and bismaleimide influences the thermal properties according to their percentage content. DSC thermogram of cyanate ester modified epoxy and bismaleimide modified epoxy show unimodel reaction exotherms. The thermal degradation temperature and heat distortion temperature of the cured bismaleimide modified epoxy and cyanate ester-epoxy systems increased with increasing bismaleimide content. The morphology of the bismaleimide modified epoxy and cyanate ester-epoxy systems were also studied by scanning electron microscopy. Copyright © 2003 John Wiley & Sons, Ltd.     

Novel ethero atoms containing polyesters based on 2,6‐naphthalendicarboxylic acid: A comparative study with poly(butylene naphthalate)

Poly(butylene naphthalate) (PBN), poly(diethylene naphthalate) (PDEN), and poly(thiodiethylene naphthalate) (PTDEN) were synthesized and characterized in terms of chemical structure and molecular weight. The polyesters were examined by TGA, DSC, and DMTA. All the polymers showed a good thermal stability, even though depending on chemical structure. At room temperature they appeared as semicrystalline materials; the effect of the introduction along the PBN polymer chain of ether oxygen atoms or sulfur ones was a lowering in the T_g value, a decrement of T_m, and a decrease of the crystallization rate. Changing in chemical structure also affects the main α absorption associated with the glass transition which moves to lower temperature and whose energetic requirements decrease. The results were explained as due to the presence of highly flexible C? S? C or C? O? C bonds in the polymeric chain. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1694–1703, 2007     

Synthesis and characterization of poly(vinyl alcohol)‐graft‐[poly(D,L‐lactide)/poly(D,L‐lactide‐co‐glycolide)] hydrogels

Poly(D ,L ‐lactide) and poly(D ,L ‐lactide‐co‐glycolide) with various composition and with one methacrylate and one carboxylate end group were synthesized and grafted onto poly(vinyl alcohol) (PVA) via the carboxylate group. The graft copolymers were crosslinked via the methacrylate groups using a free radical initiator. The polymer networks were characterized by means of NMR and studied qualitatively by means of IR spectroscopy. The influence of the glycolide content in the polyester grafts and of the number of ester units in the grafts on thermal properties and swellability were studied as well. The high swellability in water is characteristic of all hydrogels. Differential scanning calorimetry (DSC) showed a single glass transition temperature that occurs in the range between 51 and 69 °C. Thermogravimetric analysis (TGA) of the networks showed the main loss in weight in the temperature range between 290 and 370 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4536–4544, 2007     

医疗和危险废物高温洁净热处理及环境力学

结合2003年中国的突发危害公众健康的事件，分析了医疗、化学战剂及危险废物的分类、特性，比较了各种高温热处理技术的基本要求，方法分类和设备特点，包括：各类焚烧炉、热解炉和等离子体裂解装置．还对前处理工艺要求，尾气处理工艺等进行了分析讨论，讨论了防止二次污染的技术手段，特别介绍了二噁英等高危险性产物的特性．还介绍了发达国家的医疗废物和危险废物的管理、处置和二次污染防治等情况．     

Preparation,thermal properties,and flame retardance of epoxy–silica hybrid resins

A novel epoxy system was developed through the in situ curing of bisphenol A type epoxy and 4,4′‐diaminodiphenylmethane with the sol–gel reaction of a phosphorus‐containing trimethoxysilane (DOPO–GPTMS), which was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) with 3‐glycidoxypropyltrimethoxysilane (GPTMS). The preparation of DOPO–GPTMS was confirmed with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. The resulting organic–inorganic hybrid epoxy resins exhibited a high glass‐transition temperature (167 °C), good thermal stability over 320 °C, and a high limited oxygen index of 28.5. The synergism of phosphorus and silicon on flame retardance was observed. Moreover, the kinetics of the thermal oxidative degradation of the hybrid epoxy resins were studied. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2354–2367, 2003