Steady drainage in emulsions: corrections for surface Plateau borders and a model for high aqueous volume fraction

We compare extensive experimental results for the gravity-driven steady drainage of oil-in-water emulsions with two theoretical predictions, both based on the assumption of Poiseuille flow. The first is from standard foam drainage theory, applicable at low aqueous volume fractions, for which a correction is derived to account for the effects of the confinement of the emulsion. The second arises from considering the permeability of a model porous medium consisting of solid sphere packings, applicable at higher aqueous volume fractions. We find quantitative agreement between experiment and the foam drainage theory at low aqueous volume fractions. At higher aqueous volume fractions, the reduced flow rate calculated from the permeability theory approaches the master curve of the experimental data. Our experimental data demonstrates the analogy between the problem of electrical flow and liquid flow through foams and emulsions.     

Impact of titanate coupling agent on properties of high density polyethylene composite filled with coal gangue

In this study, surface modification of coal gangue (CG) was performed with titanate coupling agent 201 (isopropyl tri(dioctylpyrophosphate) titanate), and the effects of surface modifier on mechanical properties and thermal stability of high-density polyethylene filled with CG (HDPE/CG) and high-density polyethylene filled with modified CG (HDPE/mCG) composites were investigated. The coupling agent was successfully grafted on CG surface through chemical reaction according to the analyses of Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), and the coupling agent can effectively enhance the hydrophobicity of surface that was verified by water contact angle beyond 90° of modified CG sample. With the introduction of coupling agent, some enhancements of tensile strength, flexural strength, and impact strength were observed in HDPE/mCG compared with HDPE/CG, due to the improved compatibility between mCG fillers and matrix. The increased storage modulus and decreased loss factor of HDPE/mCG composite further confirm the stronger interface adhesion after modification. Moreover, it is found that titanate coupling agent 201 can improve the thermal stability of HDPE/mCG composite to some extent.     

二次包覆法制备煤沥青基硅/碳复合物及其锂离子电池性能

本文采用市售纳米硅为硅源,以软化点低、得碳率高、价格便宜的煤沥青作为碳源,通过两步包覆法制备了煤沥青基硅/碳(Si/C/C)复合物,并研究其作为锂离子电池负极材料的电化学性能。 结果表明,所得复合物的粒径在300~350 nm间,Si纳米粒子被C包覆并相互连结成C-Si-C网络结构,其中Si含量为27%的硅/碳复合物(Si/C/C-27%)作为锂电池电极材料表现了良好的储锂性能。 在0.1 A/g的小电流密度下,Si/C/C-27%的放电比容量为1281 mA·h/g;在3 A/g的大电流密度下,其放电比容量仍能保持在582 mA·h/g,表现了良好的倍率性能。Si/C/C-27%在2 A/g的电流密度下经过100次的循环后其比容量保持率为76.61%,表现了良好的循环稳定性。 相比于煤沥青基碳的一次包覆所得的硅/碳复合材料(Si/C),Si/C/C有效提高了Si纳米粒子的导电性并抑制了其在嵌锂和脱锂过程中的体积膨胀。 本文提出的二次包覆的新方法为制备具有优异电化学性能的锂离子电池负极材料提供了新的研究思路。     

Molecular Simulation on Competitive Adsorption Differences of Gas with Different Pore Sizes in Coal

Micropores are the primary sites for methane occurrence in coal. Studying the regularity of methane occurrence in micropores is significant for targeted displacement and other yield-increasing measures in the future. This study used simplified graphene sheets as pore walls to construct coal-structural models with pore sizes of 1 nm, 2 nm, and 4 nm. Based on the Grand Canonical Monte Carlo (GCMC) and molecular dynamics theory, we simulated the adsorption characteristics of methane in pores of different sizes. The results showed that the adsorption capacity was positively correlated with the pore size for pure gas adsorption. The adsorption capacity increased with pressure and pore size for competitive adsorption of binary mixtures in pores. As the average isosteric heat decreased, the interaction between the gas and the pore wall weakened, and the desorption amount of CH₄ decreased. In ultramicropores, the high concentration of CO₂ (50–70%) is more conducive to CH₄ desorption; however, when the CO₂ concentration is greater than 70%, the corresponding CH₄ adsorption amount is meager, and the selected adsorption coefficient S_CO2/CH4 is small. Therefore, to achieve effective desorption of methane in coal micropores, relatively low pressure (4–6 MPa) and a relatively low CO₂ concentration (50–70%) should be selected in the process of increasing methane production by CO₂ injection in later stages. These research results provide theoretical support for gas injection to promote CH₄ desorption in coal pores and to increase yield.     

偏最小二乘法结合傅里叶变换红外漫反射光谱快速测定煤质

发热量、挥发分和灰分等是衡量煤质的质量指标。通常,烟煤的发热量、挥发分和灰分是按行业标准方法[1]分别进行测定的,操作过程繁琐,速度慢,且费用高。随着化学计量学多元校正方法的发展与广泛应用,董庆年采用最小二乘法结合红外光谱成功测定了灰分[2];而应用偏最小二乘法[3](P     

纳米悬浮液热导率测量及其预测模型的探讨

纳米颗粒悬浮液具有广泛应用于强化传热的潜在优势。本文采用加入表面活性剂的方法提高纳米悬浮液的悬浮稳定性,并用瞬态热线法测量了热导率。在分析现有理论模型和纳米悬浮液热导率影响因素研究的基础上,从弹性传动和非弹性传动两方面分析了纳米尺度效应导致纳米悬浮液热导率提高的机理。发现已有的理论公式仍然存在一定欠缺,预测值比实验值偏低,有关机理尚有待于深入探讨。     

基于简单碰撞理论煤粉燃烧动力学模型的研究-PART Ⅲ:氧气可达比表面积

根据不同温度下氧分子平均自由程的大小,比较了小孔、中孔和大孔中三种扩散速率与煤焦表面燃烧速度的大小.研究表明2000 K以内,颗粒表面分子扩散速率比氧化反应速率大1个数量级以上,过度扩散速率不小于氧化速率.温度小于1200K时,燃烧速率比Knudsen扩散速率小1～5个数量级,扩散孔径小于15～28 nm,反应主要在内外表面进行;1200～1600K时,燃烧速率与Knudsen扩散速率相当,扩散临界孔径28～38 nm,反应在外表面及浅层内表面进行;温度1600K以上时,Knudsen扩散速率比燃烧速率小1个数量级,孔径38～50 nm以下内表面上碳的氧化速度受扩散控制.煤焦的氧化主要发生在Knudsen扩散临界孔径10～50 nm以上的氧气可达表面上.     

水稻糙米粗蛋白近红外光谱定量分析模型的优化研究

筛选有代表性的191份糙米样品为试材,其中42份来自国家稻种资源库、149份来自水旱稻杂交产生的DH系,蛋白质含量变幅5.90％～14.50％,采用偏最小二乘法(PLS)建立模型,并构造模型的评价参数——目标函数[R/(1+RMSECV)], 同时借助校正集和验证集两个载荷向量得分二维空间投影图,对近红外定量模型进行评价和优化。结果表明: 在5 000～9 000 cm-1范围内,预处理方法为一阶导数,校正模型和外部检验的目标函数值分别为0.701和0.687;两载荷向量得分直观分布图显示样品的聚类结果与目标函数筛选结果一致,也进一步验证了目标函数是模型评价和优化的有效指标。     

Microbial liquefaction of lignite pretreated with dilute acid at elevated temperature and pressure

Two microbial cultures—ML-13 (aCandida sp.) and LSC (a fungal isolate from the University of Arkansas)—have been employed in the direct liquefaction of Louisiana lignite. Lignite samples were pretreated with nitric acid and microbial culture broths at elevated temperatures and pressures. Subsequent treatment with active cultures and culture derivatives resulted in significant solubilization of the lignite. Up to 50% liquefaction of pretreated coal (20% HNO₃ at ambient temperature and pressure) was observed in 4 d with ML-13 cultures, whereas almost 80% liquefaction occurred in a similar time period when exposing pretreated lignite to an autoclaved, cell-free culture broth.