PREPARATION AND ELECTROCHEMICAL CHARACTERISTICS OF POLYMER ELECTROLYTE MEMBRANES BASED ON SAN/PVDF-HFP BLENDS

A copolymer of poly(acrylonitrile-co-styrene) (SAN) was synthesized via an emulsion polymerization method. Novel polymer electrolyte membranes cast from the blends of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), SAN and fumed silica (SiO2) are microporous and can be used in polymer lithium-ion batteries. The membrane shows excellent characteristics such as high ionic conductivity and good mechanical strength when the mass ratio between SAN and PVDF-HFP and SiO2 is 3.5/31.5/5. The ionic conductivity of the membrane soaked in a liquid electrolyte of 1 mol/L LiPF6/EC/DMC/DEC is 4.9×10-3 S cm-1 at 25℃. The membrane is electrochemical stable up to 5.5 V versus Li /Li in the liquid electrolyte. The influences of SiO2 content on the porosity and mechanical strength of the membranes were studied. Polymer lithium-ion batteries based on the membranes were assembled and their performances were also studied.     

尼龙6,6(PA_(6,6)及其共混物结晶性能的研究

<正> 尼龙6,6(PA_(6,6))是一种典型的结晶性工程塑料,被广泛应用于纺织、机械制造等行业,但其加工温度范围较窄,耐热性差。聚醚砜(PES)具有较高的玻璃化转变温度,是非晶聚合物,可以诱发某些结晶聚合物结晶。PES与PA_(6,6)共混体系的研究报道较少,本文用熔融法将PES与PA_(6,6)制成共混物,企图改善PA_(6,6)的结晶性,以提高其耐热性,取得了较理想的结果。     

壳-核结构增韧剂超高增韧非晶共聚酯的形貌和形态

研究了马来酸酐接枝的壳核结构增韧剂 (TPEg)对非晶热塑共聚酯 (PETG)的增韧和增强效果 ,并与马来酸酐接枝的纯橡胶类增韧剂 (POEg)作了对比 .TPEg对PETG具有显著的增韧效果 ,当TPEg含量由 5%增加到 1 0 %时 ,共混物就可以发生由脆性到超高韧性的快速转变 .而POEg虽然也可以使PETG发生由脆性到韧性的快速转变 ,但转变是在较高的增韧剂含量下发生的 ,这意味着共混物的抗张强度和模量损失更多 .利用扫描电镜观察、分析了随增韧剂含量的增加 ,共混物的形貌、形态的演化过程 .共混物的缺口冲击韧性与其形貌、形态之间存在很好的对应关系 .     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对PLLA的结晶行为有较大的影响。本文利用差示扫描量热仪(DSC)和偏光显微镜(POM)对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了系统研究。结果表明随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易形保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

Phase Ordering and Crystallization Kinetics in Ultrathin Poly(ethylene oxide)/Poly(methyl methacrylate) Blend Films

Crystallization in ultrathin Poly(Ethylene Oxide)/Poly(Methyl Methacrylate) (PEO/PMMA) blend films with thickness of ca. 10 nm was investigated by means of microscopic and in situ spectroscopic methods. It was revealed that the blend films undergo a phase ordering in a humid atmosphere before or during crystallization, with PEO de-mixing with PMMA and segregating to the free film interface on the PMMA layer. The de-mixed PEO chains crystallize into a fractal-like morphology by a diffusion-limited process, and the crystal growth is 1-dimensional with Avrami exponent n ≈ 1, resulting in flat-on crystal lamellae with the PEO chains oriented normal to the film plane.     

Processing and properties of engineering plastics recycled from waste electrical and electronic equipment (WEEE)

The characteristics of engineering plastics used in the preparation of electrical and electronic equipment were studied. More specifically, their thermal response was recorded by DSC experiments, the rheological properties were investigated via MFI tests and the mechanical properties were evaluated with tensile tests. The aim was to establish a procedure for recycling the same engineering plastics deriving from waste of electrical and electronic equipment (WEEE), which offers the additional advantage of using the as-received waste stream as a recyclable mixture, i.e. without sorting and classification of its components.The experimental results showed that blends of PC with ABS or ABS/HIPS can be prepared by direct mixing and this, would allow easy handling of the engineering plastics coming from WEEE, i.e. blending without the need of sorting. These mixtures can be easily processed and display acceptable mechanical properties with reasonable cost. Therefore, the processing characteristics and properties of the systems studied in this work could be the key for the design of an interesting approach for handling solid plastic waste from electrical and electronic devices.     

Compatibility and characteristics of poly(butylene succinate) and propylene-co-ethylene copolymer blend

Propylene-co-ethylene elastomer resin (PER) has been blended into biodegradable poly(butylene succinate) copolymer (PBS) by a melt-blending process to develop a novel semi-biodegradable thermoplastic elastomer. The PBS/PER blends displayed good compatibility in the range 70/30 > PBS/PER > 30/70 according to analyses by DSC, DMA and the Couchman method. Although the PBS/PER blends displayed compatibility, SEM analyses of most of the PBS/PER blends revealed two-phase structures including sea-island and irregular fiber-shaped morphologies, except for PBS/PER (70/30). PBS/PER (60/40) and PBS/PER (50/50) display low tensile strength due to large sea-phase and irregular fiber-shaped morphologies, even though they have good compatibility. PBS/PER (70/30) apparently exhibited a single phase by SEM and showed the best compatibility by DSC and DMA. Furthermore, the tan δ, elongation and initial moduli of the PBS/PER blends were seen to increase with increasing PER content, indicating that the toughness and shock resistance of PBS are improved by incorporating PER into the composition.     

End group effect on surface and interfacial segregation in PS-PMMA blend thin films

Thin films of polystyrene (PS)/poly (methyl methacrylate) (PMMA) blends with different end groups were investigated using ToF-SIMS and AFM. PS with -OH and -NH₂ end groups were blended in toluene solvent with pure PMMA homopolymer, and PMMA having anhydride end group. The ToF-SIMS spectra of PS-OH/PMMA resembled that of pure PS-PMMA blends showing an increase of PMMA intensity after annealing. On the contrary, the PS-NH₂ blended with PMMA showed an increase in PS intensity on the surface after annealing. The ToF-SIMS spectra were similar to that of a pure PS-PMMA di-block copolymer. These results indicate copolymer formation at the surface. The PS-NH₂ with PMMA-anhydride blend spectra showed very slight changes in spectra before and after annealing and the AFM images revealed spinodal bi-continuous structures on the surface before and after annealing. The copolymer formation is found to occur in the as-cast film itself and not after thermal treatment.     

Miscibility studies on blends of cellulose acetate and nylon 6

Miscibility studies on cellulose secondary acetate(CA)/Nylon 6(N6) blends have been carried out in this work. Dilute solution viscometry for the blend solutions using formic acid as the common solvent shows the existence of miscibility window.     

Morphology development of a PS/PMMA polymer blend during flow in dies

The morphology development in dilute and semi-concentrated blends (2 and 15 wt% disperse phase) of viscoelastic polymers is studied during flow in dies. In the entrance region the droplets deform into fibrils. In the die itself some of the fibrils can break up depending on their shear history and hence on their radial position. The morphology at the exit of the die is investigated by quenching the extrudate and visualizing the structure via scanning electron microscopy (SEM). For fibrils moving along the die axis, the theory of Tomotika for break-up of a fibril in a quiescent matrix describes the observations satisfactorily. Fibrils flowing off center undergo a shearing flow in the die, which could have an effect on the growth of the Rayleigh disturbances that cause break-up. It is observed that during flow break-up still occurs via Rayleigh instabilities. As a first approximation the theory of Tomotika also predicts the break-up of fibrils flowing off center, if the viscosity at the relevant shear rate is used.