共焦显微拉曼光谱技术在墨迹鉴定方面的应用

利用共焦显微拉曼光谱技术,用可见514.5nm和紫外325nm激光器作激发光源,分别测试了不同品牌的黑色圆珠笔,蓝色圆珠笔和黑色签字笔墨迹的拉曼谱图。在可见514.5nm激光器的激发下,黑色和蓝色圆珠笔墨迹都呈现了丰富的拉曼特征峰而黑色签字笔仅出现了碳峰的信号;此时改换325nm激光器来激发,发现黑色签字笔墨迹出现了清晰的拉曼特征谱峰。通过实验数据对比发现:同一类型且不同品牌笔的墨迹拉曼特征谱峰也存在一定的差异,同一种品牌墨迹的拉曼峰都保持了相对的稳定性。实验结果将为鉴定签字笔和圆珠笔油墨种类提供了法庭科学依据。它的最大优点就在于对样品的无损性,其次还有快速、无需对样品预处理和测试方法简单等。     

SQUID用于铍材残余应力检测的计算机模拟

依据SMM-601型超导量子干涉显微镜检测部分构建计算模型,采用电磁场有限元方法分析了残余应力引起的非磁性金属材料铍电导率变化对超导量子干涉仪(SQUID)检测信号的影响,并讨论了该方法实际应用于非磁性金属材料残余应力检测的条件和可能性。     

La0.7Ca0.3Mn1-xCrxO3的激光超声研究

运用激光超声的方法测定了五种不同掺杂的巨磁锰氧化物La0.7Ca0.3Mn1-xCrxO3(0.01≤x≤0.60)室温(300 K)下的超声纵波声速.结合热导率的数据,对声速随掺杂浓度的变化原因进行了深入的分析.得到在顺磁绝缘态Cr3 离子的掺入造成了晶格局部涨落的变化,低掺杂使得晶格局部涨落增强,声子U散射弛豫时间减小.     

基于超声相控阵和逆时偏移成像的套筒灌浆饱满度无损检测方法

灌浆套筒连接是装配式建筑应用主要的连接方式之一,套筒的灌浆饱满度决定了装配式建筑的稳定性和抗震性。本文提出一种基于逆时偏移(RTM)成像算法的相控阵超声检测方法,可对装配式套筒连接处可能存在的灌浆缺陷进行检测,本文通过数值仿真试验和室内模型试验对所提方法的有效性进行了验证,其中数值仿真结果表明：RTM算法与传统超声全聚焦(TFM)算法相比,具有更高的成像精度和清晰度,能准确识别套筒内部的空洞、不密实等灌浆缺陷。室内试验结果表明：在RTM重构图像中,与灌浆密实套筒相比,灌浆不密实套筒的反射信号会低9dB,此特征可以识别注浆缺陷。研究结果表明本文提出的相控阵超声成像方法适用于预制结构的套筒灌浆缺陷检测。     

新鲜苹果汁可溶性固形物含量的傅里叶变换近红外光谱检测

用傅里叶变换近红外(FTNIR)光谱透射方式对新鲜苹果汁溶性固形物含量(SSC)进行了快速定量分析。实验共测定了60个果汁样品的SSC,并采集了样品的近红外光谱数据。42个样品用来建模,剩下的18个用来验证模型的性能。对实验室测得的SSC与FTNIR光谱数据进行相关性分析,以TQ 6.2.1定量分析软件中集成的主成分回归法(PCR)和偏最小二乘回归法(PLS)建立了检测模型。该研究对比了不同光谱范围内建立的检测模型的性能。根据预测平方根误差(RMSEP)和相关系数(r2)进行不同模型的预测性能,最好的新鲜苹果汁SSC预测模型的RMSEP＝0.603 0Brix,r2＝0.997。结果表明FT-NIR可以作为一种可靠、准确、快速的无损检测方法来评价新鲜果汁的可溶性固形物含量。     

基于超声波换能器的钢筋机械损伤与锈蚀损伤检测及其对比研究

超声导波检测技术有检测耗时少、覆盖范围大等优点.为检测钢筋混凝土结构中钢筋损伤,采用超声波换能器研究不同深度和位置的机械损伤对超声导波传播的影响,建立损伤程度与导波特征关系.通过反射系数C定量分析损伤程度,并结合损伤反射回波判断损伤位置.在钢筋点锈蚀以及均匀锈蚀损伤检测中,锈蚀程度达到最大时,L波实际波速分别为4 738.1 m·s^-1和5 069.7 m·s^-1,以此区分锈蚀损伤与机械损伤,最后基于小波变换的时频分析判断损伤状况.研究成果可为钢筋损伤检测研究提供参考.     

The simulation of ultrasonic beams with a Gaussian beam equivalent point source model

Point Sources and Gaussian beams are used frequently as fundamental building blocks for developing ultrasonic beam models. Both these models have different weaknesses that limit their effectiveness. Here, we will show that one can develop a Gaussian Beam Equivalent Point Source （GBEPS） model that removes those weaknesses and combines the accuracy and versatility of the point source models with much of the speed and well-behaved nature of Gaussian beam models. We will demonstrate the efficiency and versatility of this new GBEPS model in simulating the beams generated from ultrasonic phased arrays, using as few as one Gaussian beam per element of the array. A single element GBEPS model will be shown to be as accurate as a point source model even when substantial beam focusing or steering is present in the array or where the array beam is transmitted through an interface. At the same time the GBEPS model will be shown to be several orders of magnitude faster than the point source model.     

Novel correction method for X-ray beam energy fluctuation of high energy DR system with a linear detector

A high energy digital radiography (DR) testing system has generated diverse scientific and technological interest in the field of industrial non-destructive testing. However, due to the limitations of manufacturing technology for accelerators, an energy fluctuation of the X-ray beam exists and leads to bright and dark streak artifacts in the DR image. Here we report the utilization of a new software-based method to correct the fluctuation artifacts. The correction method is performed using a high pass filtering operation to extract the high frequency information that reflects the X-ray beam energy fluctuation, and then subtracting it from the original image. Our experimental results show that this method is able to rule out the artifacts effectively and is readily implemented on a practical scanning system.     

Non-contact evaluation of the resonant frequency of a microstructure using ultrasonic wave

This paper presents a novel non-contact method for evaluating the resonant frequency of a microstructure, Firstly, the microstructure under test is excited by ultrasonic waves. This excitation method does not impose any undefined load on the specimen like the electrostatic excitation and also this is the first actual use of ultrasonic wave for exciting a microstructure in the literature. Secondly, the amplitudes of the microstructure are determined by image edge detection using a Mexican hat wavelet transform on the vibrating images of the microstructure. The vibrating images are captured by a CCD camera when the microstructure is vibrated by ultrasonic waves at a series of discrete high frequencies （〉30 kHz）. Upon processing the vibrating images, the amplitudes at various excitation frequencies are obtained and an amplitude-frequency spectrum is obtained from which the resonant frequency is subsequently evaluated. A micro silicon structure consisting of a perforated plate （192 × 192 μm） and two cantilever beams （76 × 43 μm） which is about 4 μm thickness is tested. Since laser interferometry is not required, thermal effects on a test object can be avoided. Hence, the setup is relatively simple. Results show that the proposed method is a simple and effective approach for evaluating the dynamic characteristics of microstructures.     

SQUID结合涡旋电流法用于铍材残余应力检测的可行性

涡旋电流法是材料无损检测常用方法之一，近年国际上多个研究小组对用于金属材料内残余应力检测开展了研究，涡旋电流法被认为是无损检测确定材料内残余应力的潜在方案。文中从实验和电磁场数值模拟两方面对此问题开展研究。