制备均一性靶丸过程中的影响因素

在激光聚变实验中,高球形度、高厚度均一性的靶丸经常通过乳液微封装方法来制备。利用T.Norimatsu的模型研究在靶丸制备过程中,界面间表面张力、油相粘度、壳层尺寸、壳层厚度的影响。结果显示:较大的表面张力,较小的壳层尺寸,会使胶囊具有更好的均一性。当外部变形形式不同的时候,油相的粘度对于壳层均一性会有不同作用。     

宽光谱膜厚监控系统中光谱实时测量技术研究

 在宽光谱膜厚监控系统中,利用光栅光谱仪分光,线阵CCD接收,完成光谱的一次性快速扫描来控制膜层厚度,达到实时监控的要求。而系统光谱扫描的准确性,直接影响膜厚实时监控的有效性。为了得到准确的光谱信息,首先确定CCD像素和光波波长的对应关系,基于特征谱线的离散关系,采用最小二乘拟合法建立了光谱标定函数,经实验,标定波长均方根误差为0.037 nm;对于CCD实时输出的光谱监控信号,利用小波阈值优化算法抑制信号中的随机噪声,保留了光谱信号的细节成分,峰值误差的最大值为1.0%,峰位误差的最大值为0.3%,满足了监控中光谱分辨率的要求。     

不同厚度的活性层及阴极的改变对聚合物太阳电池性能的影响

以MEH-PPV(poly(2-methoxy-5-(2'-ethylhexoxy)-1,4-phenylene vinylene))为电子给体材料, PCBM(1-(3-methoxycarbonyl)-propyl-1-1-phenyl-(6,6)C₆₁)为电子受体材料, 制成了共混体系太阳电池.研究了不同厚度活性层对太阳电池性能的影响.结果表明, 活性层厚度为100 nm时,太阳电池具有最佳性能.活性层厚度的增加,增大了光生电荷的复合,减少了太阳电池的填充因子,从而减少了太阳电 关键词： 太阳电池 厚度 电极 性能     

Analysis of ultrasonic guided waves propagating in long bones and cortical thickness based on time-frequency methods

The ultrasonic signals in long bones contain multiple guided modes which are mutual superposed.The velocities of guided waves in long bones are very sensitive to cortical thickness (CTh).In this paper,Hilbert-Huang transform(HHT) was proposed to analyze multi-mode guided waves,which can decompose superposed waves into many independent modes.Then the group velocity of each mode was obtained at corresponding frequency,which was compared with the results of short time Fourier transform(STFT).The CTh was also obtained by comparing with the theoretical calculation.The results showed that the experimental determined thickness was in agreement with the actual CTh,indicating that measuring the velocity of the guided mode can be used to estimate the CTh.The HHT is an effective method to identify multimode guided waves.     

A new probe of neutron skin thickness

The correlation between neutron-to-proton yield ratio (R_np) and neutron skin thickness (δ_np) in neutron-rich projectile induced reactions is investigated within the framework of the Isospin-Dependent Quantum Molecular Dynamics (IQMD) model. The density distribution of the Droplet model is embedded in the initialization of the neutron and proton densities in the present IQMD model. By adjusting the diffuseness parameter of neutron density in the Droplet model for the projectile, the relationship between the neutron skin thickness and the corresponding R_np is obtained. The results show strong linear correlation between R_np and δ_np for neutron-rich Ca and Ni isotopes. It is suggested that R_np may be used as an experimental observable to extract δ_np for neutron-rich nuclei, which is very interesting in the study of the nuclear structure of exotic nuclei, the equation of state (EOS) of asymmetric nuclear matter and neutron-rich matter in astrophysics, etc.     

梯度磁场中薄膜厚度梯度的形成机理

借助于基片下方放置的磁铁，在溅射的放电空间中引入了纵向的梯度磁场，辉光放电时，其外貌发生了显著的收缩，由此沉积的薄膜在平面内存在明显的厚度梯度，用磁场中带电粒子的运动理论解释了此种薄膜的形成机制。     

半导体激光器M^2因子可以小于1

根据Porras的非傍轴矢量矩理论，对双异质结半导体激光器的光束质量进行了研究，结果表明，在有源层厚度da远小于波长λ的条件下，半导体激光器的M62因子可以小于1，并且没有下限。     

Geometry optimization in planetary rotation stage for thickness uniformity of films on spherical substrates

We report the simulation results on the thickness uniformity of optical coatings deposited on spherical substrates by optimizing the geometric configuration parameters, such as tilting angle of the substrate holder and position of the evaporation source in a 1 000-mm-diameter planetary rotation stage （PRS）. We reveal that good film uniformity on convex spherical surfaces or flat substrates, as well as concave surfaces with weak to moderate curvatures can be obtained through appropriate tilting of the substrate holder. For 300-mm-diameter substrates with clear aperture to radius of curvature （CA/RoC） between 0.3 and 0.7, the achievable film uniformity is above 99%. The source position is optimized to achieve good film uniformity.     

Method to accurate calibrate deposition rates of EUV multilayer coatings

Random thickness error is an important factor which effects the calibration accuracies of deposition rates for extreme ultraviolet （EUV） multilayer coatings fabricated by sputter deposition techniques. A least square fitting method is proposed to determine deposition rates and extract random thickness errors accurately. The validity of this method is shown by evaluating two deposition systems with control abilities of -0.1 nm and better than 0.01 nm respectively.     

Nuclear data for the cyclotron production of ~（117）Sb and ~（90）Nb

This presented study is to make comparison of cross sections to produce ¹¹⁷Sb and ⁹⁰Nb via different reactions with particle incident energy up to 70 MeV as a part of systematic studies on particle-induced activations on enriched Sn, Y₂O₃ and ZrO₂ targets, theoretical calculation of production yield, calculation of required thickness of target and suggestion of optimum reaction to produce Antimony-117 and Niobium-90.