Cu-Mg/Al复合氧化物催化碳颗粒物燃烧性能的研究

恒定二价与三价阳离子比为3(nM2+/nM3+=3),采用共沉淀法制备不同Cu含量的系列水滑石前驱物, 800 ℃焙烧4 h形成复合氧化物(CuO质量百分数分别为0％、5％、10％、15％、20％、30％、40％)用作柴油车排放碳颗粒物燃烧的催化剂,并采用XRD、BET、TG-DSC、FT-IR、TPR等表征手段研究了Cu、Mg含量对材料前驱物物化性能的影响及对其衍生复合氧化物催化碳颗粒物燃烧性能的影响．结果表明,Cu、Mg含量对材料的热稳定性、比表面和催化氧化活性有显著的影响. Mg有助于提高催化剂的热稳定性; Cu含量增加,催化剂比表面下降,但比表面不是影响催化剂活性的主要因素. CuO含量为15％时,催化剂具有最好的催化活性和稳定性,碳颗粒物的起燃温度(T10)和半转化温度(T50)分别为336 ℃和409 ℃.在CuO含量≤30％时可以形成结构完整的水滑石前驱物, CuO含量为40％时出现Cu(OH)2杂相; CuO含量< 20％时,经高温焙烧可得到均匀的复合氧化物, CuO含量≥20％时出现CuO偏析． TPR结果表明焙烧温度和复合氧化物的组成决定了材料的可还原性能．     

旋流煤粉燃烧的一维综合数值模拟

发展了综合考虑气－固两相旋流流动，气相燃烧，颗粒相变与燃烧及两相辐射传热的旋流煤粉燃烧－维数学模型，给出了气－固两相能量方程中颗粒相就源项的计算表达式，应用这一模型对涡旋燃烧炉环形通道内多组工况的旋流气体燃烧和煤粉燃烧进行了数值模拟，计算得到的炉内温度分布和燃烧效率与实验数据基本相符，表明本文建立的模型可用于旋流煤粉燃烧的一维综合数值模拟。     

凝胶-燃烧法合成YAG∶Eu3+纳米荧光材料的结构和发光性能

Y₃Al₅O₁₂∶Eu nanophosphors were synthesized by a gel combustion method. The structure of phosphors was characterized by XRD and FTIR. YAG phase came to occur when YAG∶Eu precursors were sintered at 800 ℃, although the phase was mainly amorphous. The organic groups pyrolyzed completely and pure YAG phase was obtained in the samples sintered at 900 ℃. In the formation of YAG phase, no intermediate phases such as YAP and YAM were detected. Both ⁵D₀ → ⁷F₁ orange and ⁵D₀ → ⁷F₂ red emission could be observed for all the sintered samples. However, the emission of amorphous samples was greatly different from that of crystalline ones. The former was mainly ⁵D₀→ ⁷F₂ red emission, but the latter was ⁵D₀ → ⁷F₁ orange emission. As sintering temperature rises, the ratio of orange to red for phosphors increases. Eu could be doped up to 8% in YAG host lattice, and fluorescence quenching was absent. It indicated that the gel combustion synthesis method can increase emission intensity and quenching concentration due to a good distribution of Eu³⁺ activators in Y₃Al₅O₁₂ matrix.     

室温离子液体EMIES的标准生成焓

在(298.15 ±0.01) K下用转动弹热量计测定了离子液体硫酸乙酯-1-甲基-3-乙基咪唑(EMIES)及合成它的原料1-甲基咪唑的恒容燃烧热,通过计算得到它们的标准燃烧焓 分别为(－2671±2) 和(－286.3±0.5) kJ·mol－1;标准生成焓 分别为(－3060±3) kJ·mol－1和(－2145±4) kJ·mol－1.结合文献上硫酸二乙酯的标准生成焓数据,得到了合成离子液体EMIES的反应热(－102.3±1.0) kJ·mol－1,与合成实验中观察到的强烈放热现象是一致的.根据离子液体EMIES的热容数据,计算了不同温度下EMIES的标准生成焓.     

Storage-Reduction of NOx over Combined Catalysts of Pt/Ba/Al2O3-Mn/Ba/Al2O3： Carbon Monoxide as Reductant

Storage-reduction of NOx by carbon monoxide was investigated over combined catalysts of Mn/Ba/Al2O3-Pt/Ba/Al2O3. Combination of Mn/Ba/Al2O3 and Pt/Ba/Al2O3 catalysts in different ways showed excellent NOx storage-reduction performance and the content of Pt could be reduced by 50%. Not only the addition of 5Mn/15Ba/Al2O3 to lPt/15Ba/Al2O3 could improve its storage ability, but also enhance the NOx conversion consequently. NOx conversion over the combined catalysts (the combined catalysts I and II) was increased under dynamic lean-rich burn conditions, the maximum NOx conversion increased from 69.4% to respectively 78.8% and 75.7% over two combined catalysts.     

添加剂铜和银离子对MnO2催化燃烧CH4的影响

催化燃烧法，由于起燃温度低、去除率高、适用氧浓度范围大、无二次污染、燃烧缓和等，是国内外治理有机废气时，回收利用能量最有效的方法之一［１］．但目前用于该过程的催化剂中均含有来源有限、价格昂贵的贵金属铂或钯［２］．因此，寻找来源丰富、价格低廉、性能相当...     

氧化条件下NOx催化的甲烷均相部分氧化

考察了没有固体催化剂时NOx对甲烷气相氧化的促进作用.实验结果表明，即使在强氧化条件下（O2/CH4=5），NOx对甲烷部分氧化制一氧化碳仍然有明显的催化活性.在CH4-O2体系中加入0.005％～0.2％的NO后，反应温度可降低200-300 ℃.在反应产物中还可观察到甲醛和乙烯，通过改变反应条件可以控制它们的相对浓度.     

NiO/SnO2-ZrO2催化剂的制备及甲烷燃烧催化性能的研究

利用正交分析，通过溶胶凝胶－超临界干燥及复合浸渍的方法制备了NiO/SnO2-ZrO2催化剂，进行了活性评价，考察了前驱物、NiO、SnO2含量及制备方法对催化剂活性及稳定性的影响，并采用XRD、TEM对催化剂进行了表征分析，结果表明：NiO/SnO2-ZrO2催化剂具有良好的甲烷燃烧催化性能（t100%=640 ℃），其活性、稳定性与制备参数密切相关，其中NiO含量是影响催化剂活性、稳定性的最主要参数，它对催化剂稳定性和活性的影响规律正相反； SnO2组分的添加使ZrO2单斜相稳定，对催化剂起到了良好的稳定化作用，发现当SnO2含量在6 mol％左右时，催化剂具有较好的稳定性；对于制备方法，在凝胶前加入活性组分有利于催化剂的高活性，而在凝胶后加入活性组分，则有利于催化剂保持较好的稳定性；活性组分前驱物对催化剂性能影响不大，采用Ni(NO3)2作为前驱物较为合适。     

煤焦在燃烧过程中孔隙结构变化的模拟

煤焦在燃烧过程中的物理特性，如比表面积和孔径分布会发生连续变化，直接测量煤焦在燃烧过程中的孔隙结构变化很困难，但可以通过合适的数学模型来观察，二维的圆柱孔模型已大量用来对煤焦气化与燃烧过程中表面积和孔隙结构的变化进行模拟，这个模型把孔隙分成两大部分－－大孔与小孔，因为小孔构成比表面的绝大部分，所以在反应过程中比表面积的变化可以由单一小孔模型来拟合，本文采用了用Ｔｓｅｎｇ和Ｅｄｇａｒ提出的孔模型对几     

Catalytic Combustion of Methane over CO1-xMgxO/Al2O3/FeCrAl Monolithic Catalysts

A series of CoxMgxO/Al2O3/FeCrAl catalysts （x=0-1） were prepared. The structures of the catalysts were characterized using XRD, SEM, and TPR analyses. The catalytic activity of the catalysts for methane combustion was evaluated in a continuous flow microreactor. The results indicated that the active washcoats adhered well on the FeCrAl foils. The phases in the catalysts were Co--xMgxO solid solutions, α-Al2O3, and γ-Al2O3. The surface particle size of the catalysts varied with variations in the molar ratios of Co to Mg. The Co component of the Co1_xMgxO/Al2O3/FeCrAl catalysts played an important role in the catalytic activity for methane combustion. In the Co1-xMgxO/AluO3/FeCrAl series catalyst （x=0.2-0.8）, the catalytic activity in terms of x was in the order of 0.5〉0.2〉0.8 under the experimental conditions. The presence of Mg in these catalysts could promote the thermal stability to a large extent. There were strong interactions between the Co1-xMgxO oxides and the AluO3/FeCrAl supports.