多孔硅纳米材料的制备及在高能锂电池中的应用

多孔硅纳米材料具有巨大的比表面积,可调控的物理化学性质,在药物治疗、传感、能源储存与转化等领域拥有巨大的应用前景。尤其在高能量密度锂离子电池领域,多孔硅由于其丰富的孔道结构能有效释放充放电过程中硅体积变化带来的巨大应力以及大大地缩短锂离子传输距离,而引起了人们的广泛研究兴趣。但是,开发简便快速的方法来合成结构可调变的多孔硅纳米材料仍是当前研究的挑战。近年来,一些用来合成多孔硅纳米材料的方法已有报道。我们基于本课题组最近的研究进展和近年来相关文献,比较详细综述了近年来多孔硅纳米材料的制备方法以及重点关注其在高能锂电池领域的应用。最后,对多孔硅纳米材料的未来发展方向做了进一步的展望。     

The Mosaic Structure of Zeolite Crystals

Zeolites are widely used in many commercial processes, mostly as catalysts or adsorbents. Understanding their intimate structure at the nanoscale is the key to control their properties and design the best materials for their ever increasing uses. Herein, we report a new and controllable fluoride treatment for the non‐discriminate extraction of zeolite framework cations. This sheds new light on the sub‐structure of commercially relevant zeolite crystals: they are segmented along defect zones exposing numerous nanometer‐sized crystalline domains, separated by low‐angle boundaries, in what were apparent single‐crystals. The concentration, morphology, and distribution of such domains analyzed by electron tomography indicate that this is a common phenomenon in zeolites, independent of their structure and chemical composition. This is a milestone to better understand their growth mechanism and rationally design superior catalysts and adsorbents.     

PCB酸性蚀刻液中缓蚀剂对厚铜线路制作的影响

以2-巯基苯并噻唑(2-MBT)、 苯并三氮唑(BTA)和苯氧基乙醇(MSDS)作为缓蚀剂, 研究了其加入在酸性蚀刻液后对PCB厚铜线路的缓蚀效果。通过接触角测试、电化学测试和蚀刻因子得出缓蚀状态,并结合扫描电子显微镜观察铜表面形貌。通过分子动力学计算和量子化学模拟分析缓蚀剂在铜表面的吸附机理。结果表明,2-MBT + MSDS与BTA + MSDS的分子结构可有效地平行吸附在铜表面,且吸附能高于单一缓蚀剂。加入了2-MBT + MSDS的蚀刻液,对厚度约为33 μm铜线路进行刻蚀,铜线路的蚀刻因子提高到6.59,可有效应用于PCB厚铜线路制作。     

硅酸钇晶体的生长、腐蚀形貌和光谱性能研究

本文采用中频感应提拉法成功生长了未掺杂的Y2SiO5(YSO)晶体,经过定向、切割、抛光后得到样品.经过腐蚀后,利用大视场显微镜和扫描电镜在样品表面上观察到了菱形和四边形的位错蚀坑、小角晶界和包裹物等缺陷;测试了经过氢气、空气退火前后,辐照前后YSO晶体的透过谱,结果表明:YSO晶体的吸收边大约在202nm,氢气退火后在200～300nm波段透过率增加,空气退火后透过率显著降低;辐照后,氢气退火的样品在200～500nm波段透过率显著降低.     

光纤探针传输效率的研究

用实验方法测量了光纤探针的传输效率随光纤圆锥角的变化关系,给出了传输效率曲线。通过测定探针传输效率的实验可以看到,只要光纤探针的锥角在30°~55°范围内,就具有高透过率、高分辨率纳米微探针。测量了传输效率与光波波长的关系。     

利用线性液膜的红外热像测定YBCO的湿法化学刻蚀启动时长

提出了一种测定YBCO(YBa2Cu3O7-x)高温超导薄膜湿法腐蚀启动时长的红外热像新方法。该方法的实质是利用YBCO腐蚀时必然有化学热吸收或释放,从而引起YBCO表面液膜温度变化这一特点,通过红外热像实时监测系统,采集液膜温度变化过程的红外热像,从而判断反应启动时长。理论分析和实验结果均表明,YBCO表面2 mm宽线性液膜是较为理想的监测对象,因其同时具备温度变化信息和空间分布信息,可以将线性液膜中心作为理想的观测特征点;由滑动腐蚀液滴形成残留线性液膜具有温度变化灵敏度高的特点,YBCO(衬底为LaAlO3)竖直放置,可以表面避免液膜重力对启动时长的影响,获得更为准确的监测数据。由线性液膜的横向剖面灰度变化得到在本实验条件下YBCO薄膜与体积比H3PO4∶H2O=1∶300腐蚀液的反应启动时长介于0.3~0.4 s之间。     

Transmission Electron Microscopic Investigation of the Morphology of High-Speed Spun Poly(Ethylene Terephthalate) Fibers

Permanganic etching was performed on high-speed spun (HSS) and regular fibers of poly(ethylene terephthalate) (PET), and their surface morphologies were investigated via the two-stage carbon replica method using a transmission electron microscope (TEM). The HSS PET fibers, with disordered amorphous regions, showed peculiar surface morphology; many small warts corresponding to the pits of etched disordered amorphous regions were observed. Such unevenness, however, was hardly observed on the surface of the permanganic-etched regular PET fibers, with well-oriented amorphous regions, or on the surface of alkali-etched HSS PET fibers. The permanganic etchant removed the disordered amorphous regions more preferentially compared with the alkali etchant.     

基于后向散射模型的蒸汽湿度测量及仿真

为了更加准确地测量出汽轮机末级蒸汽湿度,为锅炉给水量提供依据,促进汽轮机内部除湿技术的发展,采用了后向角散射法的思路设计了湿蒸汽参数测量模型,并对模型所需物理量进行了详细的计算,为后向散射法测量蒸汽湿度的研究提供参考。通过对模型进行仿真模拟以及实验研究,得到了后向散射光光强数据。通过对比仿真模拟数据与实验数据,验证了该模型的可行性与有效性,对光散射法测量蒸汽湿度的实验分析以及工程实践具有重要意义。     

Fabrication of extreme wettability patterns with water-film protection for organic liquids

Selective fabrication of superhydrophilic (S-philic) region on a superhydrophobic (S-phobic) surface requires complex technology and high cost, which has limited applications of extreme wettability patterns. In this paper, a twice-chemical-etching approach without special modification is used to prepare the extreme wettability patterns. Superhydrophobicity and superhydrophilicity can be successfully achieved after twice chemical etching for 20 seconds. The obtained patterns can maintain their extreme wettability for at least 30 days. Functional platforms with single-S-philic and multi-S-philic regions are fabricated to manipulate water and various organic liquids with water-film protection in an air environment.     

湿工况下平直翅片对流传热传质数值研究

建立了湿空气流经平直翅片通道并伴有凝结现象发生的三维对流传热传质的数值模型,在空气进口雷诺数Re为190～3770,进口相对湿度φ_(in)为50%～90%的范围内,对干湿两种工况,平直翅片通道内的换热流动进行了对比研究。结果表明:湿工况换热系数为干工况换热系数的2.8～3.1倍,干工况翅片效率比湿工况翅片效率高35.8%～41.9%。当翅片为部分湿工况时,翅片效率随进口相对湿度的增大而增大,换热系数随进口相对湿度的增大而减小;当翅片为全湿工况后,进口相对湿度对翅片效率和换热系数的影响微弱。