Performance of a CW pumped Nd:YVO4 amplifier with kHz pulses

Until recently, simple and reliable high repetition-rate laser sources with nanosecond pulses much shorter than from conventional A-O Q-switch lasers were not available. However over the past 2 years we have developed such lasers based on proprietary fast E-O switching technology, which allows designs delivering 1 ns pulses and subnanosecond jitter for good synchronisation. The technology provides pulses with multi-kW peak power and repetition-rates to >100 kHz.Most recently, the performance of these short pulse lasers has been developed further by implementing oscillator/amplifier (master oscillator and power amplifier, MOPA) technology which increases the output to >1 W average power. Here we report on a simple model that has been used to predict the performance of the CW pumped Nd:YVO₄ amplifier used in the MOPA laser. The model is based on the well-known expressions for the saturated gain applying to laser pulses, but more usually applied to pulse-excited amplifiers. The model is shown to allow a good interpretation of the amplifier behaviour for kHz pulses and to be a useful tool for predicting the performance of the MOPA laser.     

Champ de vitesse dans un échangeur à vortex en régime turbulentHeat exchanger velocity field with turbulent inlet condition

We consider the isothermal flow through a cylindrical flat chamber, a model of some particular heat exchanger, for which LDV measurements and a numerical simulation have been performed. Experimental results show the establishment of an important vortex zone, the secondary flow extending all along the chamber radius. This observation leads to an expected significant increase of the fluid mixing. Results issued from the numerical simulation appear to be in close agreement with experimental data. Nevertheless, the k–ε model used here must be improved to obtain a better approach near the vortex centre. To cite this article: S. Petitot et al., C. R. Mecanique 330 (2002) 593–599.     

Study on the possibilities of controlling the laser output beam properties by an intracavity deformable mirror

The possibilities of controlling the laser beam properties by a deformable mirror introduced into the laser optical cavity were studied theoretically and experimentally. The experiments were performed under conditions of an industrial high power transverse flow cw CO₂ laser operating with a stable resonator of a folded configuration. A deformable bimorph mirror of a surface profile controlled by the voltage applied to the mirror electrodes is implemented to the laser system as a back cavity mirror or as a one of the inner folding mirrors. The near-and far-field characteristics of the laser beam versus the resonator configuration controlled by the changes of the focal length of the deformable mirror are discussed in the paper. The analysis reveals that the resonator with an inner deformable mirror is much more sensitive to the mirror curvature variations than the resonator in which the deformable mirror is used as a back cavity mirror. The presented results show that dynamic and controllable changes in the resonator properties result in the controlled modification and optimisation of the laser output power and spatial parameters of the laser radiation.     

Separate Polarization Modes Synchronization and Synchronization Switches between Vertical-Cavity Surface-Emitting Lasers

For vertical-cavity surface-emitting lasers (VCSELs) with polarization-rotated feedback, there exist several synchronization types such as synchronizations between total powers and synchronizations between separate polarization modes. Based on the two-mode rate equations, we study and compare numerically the performances of different synchronization types. Our results show that three synchronization types exhibit good performances when their synchronization conditions are satisfied. They are the complete synchronization between total powers, complete synchronization between x-polarized modes, and generalized synchronization between x-polarized and y-polarized modes. The former two types are sensitive to the injection rate and spontaneous emission, while the third type is contrary. Synchronization type with the best performance may switch from one to another, with changing of injection rate and spontaneous emission factor.     

Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

The Properties of Light Pressure Force with High Order in Laser Fields

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｒｅｃｅｎｔｙｅａｒｓ,ｂｏｔｈｔｈｅｔｈｅｏｒｅｔｉｃａｌａｎｄｅｘｐｅｒｉｍｅｎｔａｌｉｎｖｅｓｔｉｇａｔｉｏｎｓｏｎｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｈａｖｅｂｅｃｏｍｅｏｎｅｏｆｔｈｅｍａｊｏｒｆｉｅｌｄｓｉｎａｔｏｍｉｃ,ｍｏｌｅｃｕｌａｒａｎｄｏｐｔｉｃａｌ ｐｈｙｓｉｃｓ[1～ 8] .Ｔｈｅｄｅｖｅｌｏｐｍｅｎｔｏｆｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｔｅｃｈｎｏｌｏｇｙｉｓｉｍｐｏｒｔａｎｔｆｏｒｔｈｅａｐｐｌｉｃａｔｉｏｎｓｓｕ…     

Pulsed laser deposition of nanostructured Ag films

Ultra-thin (0.5-5 nm) films of Ag have been prepared by pulsed laser deposition in vacuum using a 26 ns KrF excimer laser at 1 J cm⁻². The deposition was controlled using a Langmuir ion probe and a quartz crystal thickness monitor. Transmission electron microscopy showed that the films are not continuous, but are structured on nanometer size scales. Optical absorption spectra showed the expected surface plasmon resonance feature, which shifted to longer wavelength and increased in strength as the equivalent film thickness was increased. It is shown that Maxwell Garnett effective medium theory can be used to calculate the main features of optical absorption spectra.     

Laser spectroscopic investigation of a new precursor-type polyparaphenylenevinylene

Optical, structural and morphological properties of thin films of polyparaphenylenevinylene (PPV) formed by an alkyl sulfinyl precursor route have been studied. Thin films were fabricated on an optical glass and on quartz glass either by spin-coating of the precursor solution or by layer-by-layer deposition using Langmuir–Blodgett technique. PPV precursor films were also spin-coated on gold-coated glass in order to study thin-film optical parameters by surface plasmon spectroscopy. We have been successful in forming about 40 precursor mono layers on quartz glass by Langmuir–Blodgett technique using optimized surface pressure and dipping conditions. After thermal conversion of the precursor layers good quality fluorescent PPV films of yellow colour have been obtained. Optical characterization of the films was carried out by linear absorption and emission spectroscopy, ellipsometry, and surface plasmon spectroscopy. Structural and morphological studies on the thin films were carried out by using X-ray scattering and atomic force microscopy. Wave-guided travelling-wave laser action has been achieved in a PPV film on quartz glass. The sample was transversally pumped with picosecond laser pulses (wavelength 347.15 nm, duration 35 ps). Laser emission occurred at 550 nm for pump pulse energy densities above .     

Changes in the Laser-Induced Fluorescence Spectrum of Myocardium Tissue with Decrease in Its Viability

We investigated the laser-induced fluorescence spectra (LIF) of porcine cardiac tissues with different degrees of viability. The data obtained are compared with the results of routine histological investigations and also with the experiments performed with the use of fluorescent probes. It has been found with a high degree of reliability that the loss of the viability of the myocardium tissue leads to the alteration of its LIF spectra. This can be used for low-invasive rapid control of transplant viability in the process of its preparation and during surgery.     

Submicrometric Displacement and Vibration Measurement Using Optical Feedback in a Fiber Laser

A very simple and efficient technique for the remote sensing of a noncooperative target is presented. This technique is based on the frequency-shifted reinjection of light in a class B laser. Ytterbium- and erbium-doped fiber lasers have both been used to measure displacements with a submicrometric resolution and the vibration power spectrum of an object.