Dielectric,thermal, and mechanical properties of CeO2‐filled HDPE composites for microwave substrate applications

Cerium oxide‐filled high density polyethylene (HDPE) composites for microwave substrate applications were prepared by sigma‐blend technique. The HDPE was used as the matrix and the dispersion of CeO₂ in the composite was varied up to 0.5 by volume fraction, and the dielectric properties were studied at 1 MHz and microwave frequencies. The variations of thermal conductivity (k_eff), coefficient of thermal expansion (α_c) and Vicker's microhardness with the volume fraction of the filler were also measured. The relative permittivity (ε_eff) and dielectric loss (tan δ) were found to increase with increase in CeO₂ content. For 0.4 volume fraction loading of the ceramic, the composite had ε_eff = 5.7, tan δ = 0.0068 (at 7 GHz), k_eff = 2.6 W/m °C, α_c = 98.5 ppm/°C, Vicker's microhardness of 18 kg/mm² and tensile strength of 14.6 MPa. Different theoretical approaches have been used to predict the effective permittivity, thermal conductivity, and coefficient of thermal expansion of composite systems and the results were compared with the experimental data. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 998–1008, 2010     

Characterization of the mesostructure of HDPE under “in situ” uniaxial tensile test by incoherent polarized steady‐light transport

This study presents quantitative results related to in situ investigation of the microstructural evolutions of high‐density polyethylene with deformation. These results were obtained thanks to a novel technique (IPSLT) based on the polarized light scattering transport phenomenon. The heterogeneities produced during whitening of the polymer bulk are characterized at the mesoscale level (from hundred of nanometers to a few micrometers). The technique is described as well as the identified parameters it provides, namely: the average size of the scatterers, the anisotropy developed in the medium, and the light transport length, representative of both the volume fraction and size of the heterogeneities. Results obtained during video‐controlled tensile experiments confirm those obtained previously with X‐ray microtomography. They put forward the role of morphological transformations of the amorphous/crystalline phases (especially regarding the creation of fibrillar assemblies) rather than the cavitation phenomenon. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Anionic polymerization of N,N‐dialkyl‐2‐methylenebut‐3‐enamide: Effect of alkyl substituents on polymerization behavior

Anionic polymerizations of three 1,3‐butadiene derivatives containing different N,N‐dialkyl amide functions, N,N‐diisopropylamide (DiPA), piperidineamide (PiA), and cis‐2,6‐dimethylpiperidineamide (DMPA) were performed under various conditions, and their polymerization behavior was compared with that of N,N‐diethylamide analogue (DEA), which was previously reported. When polymerization of DiPA was performed at ?78 °C with potassium counter ion, only trace amounts of oligomers were formed, whereas polymers with a narrow molecular weight distribution were obtained in moderate yield when DiPA was polymerized at 0 °C in the presence of LiCl. Decrease in molecular weight and broadening of molecular weight distribution were observed when polymerization was performed at a higher temperature of 20 °C, presumably because of the effect of ceiling temperature. In the case of DMPA, no polymer was formed at 0 °C and polymers with relatively broad molecular weight distributions (M_w/M_n = 1.2) were obtained at 20 °C. The polymerization rate of PiA was much faster than that of the other monomers, and poly(PiA) was obtained in high yield even at ?78 °C in 24 h. The microstructure of the resulting polymers were exclusively 1,4‐ for poly(DMPA), whereas 20–30% of the 1,2‐structure was contained in poly(DiPA) and poly(PiA). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3714–3721, 2010     

ESR和NMR在茂金属催化剂和聚烯烃研究中的应用

随着高分子科学和催化技术的发展，了解聚合物和催化剂的微结构信息尤为重要. 主要介绍了ESR和NMR在茂金属催化剂和聚烯烃领域中的最新应用，研究成果表明ESR和NMR是研究聚合物和催化剂微观信息的有效工具.     

柚子型微结构光纤Bragg光栅温度和应变传感特性研究

通过对柚子型微结构光纤Bragg光栅的多个反射峰的温度和应变传感特性进行的理论和实验 研究，得出柚子型微结构光纤Bragg光栅的反射波长与温度呈二次关系，且理论和实验二者 吻合较好; 同时发现每个反射峰的温度灵敏度不同.理论分析柚子型微结构光纤Bragg光栅的 反射波长与应变呈线性关系，实验得到了该种Bragg光栅的反射波长与应变的线性关系，实 验结果与理论分析相吻合.由于微结构光纤光栅反射谱中多个峰对温度和应变等物理量敏感 度不一致，这种Bragg光栅更适合应用到多参量传感领域. 关键词： 微结构光纤 光纤Bragg光栅 温度传感 应变传感     

Breadth of glass transition temperature in styrene/acrylic acid block,random, and gradient copolymers: Unusual sequence distribution effects

Block, random, and gradient copolymers of styrene (S) and acrylic acid (AA) are synthesized by conventional or controlled radical polymerization, and their glass transition temperature (T_g) behaviors are compared. The location and breadth of the T_gs are determined using derivatives of differential scanning calorimetry heating curves. Each S/AA random copolymer exhibits one narrow T_g, consistent with a single phase of limited compositional nanoheterogeneity. Block copolymers exhibit two narrow T_gs originating from nanophase separation into ordered domains with nearly pure S or nearly pure AA repeat units. Each gradient copolymer exhibits a T_g response with a ～50–56 °C breadth that extends beyond the upper T_g of the block copolymers. For copolymers of similar composition, the maximum value in the gradient copolymer T_g response is consistent with that of a random copolymer, which has an enhanced T_g relative to poly(acrylic acid) due to more effective hydrogen bonding when AA units are separated along the chain backbone by S units. These results indicate that gradient copolymers with ordered nanostructures can be rationally designed, which exhibit broad glass transitions that extend to higher temperature than the T_gs observed with block copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2842–2849, 2007     

A study of direct- and pulse-current chromium electroplating on rotating cylinder electrode (RCE)

Direct- and pulse-current (DC and PC) chromium electroplating on Cr-Mo steel were performed in a sulfate-catalyzed chromic acid solution at 50 °C using a rotating cylinder electrode (RCE). The electroplating cathodic current densities were at 30, 40, 50 and 60 A dm⁻², respectively. The relationship between electroplating current efficiency and the rotating speed of the RCE was studied. The cross-sectional microstructure of Cr-deposit was examined by transmission electron microscope (TEM). Results showed that DC-plating exhibited higher current efficiency than the PC-plating under the same conditions of electroplating current density and the rotating speed. We found the critical rotating speed of RCE used in the chromium electroplating, above this rotating speed the chromium deposition is prohibited. At the same plating current density, the critical rotating speed for DC-plating was higher than that for PC-plating. The higher plating current density is, the larger difference in critical rotating speeds appears between DC- and PC-electroplating. Equiaxed grains, in a nanoscale size with lower dislocation density, nucleate on the cathodic surface in both DC- and PC-electroplating. Adjacent to the equiaxed grains, textured grains were found in other portion of chromium deposit. Fine columnar grains were observed in the DC-electroplated deposit. On the other hand, very long slender grains with high degree of preferred orientation were detected in PC-electroplated deposit.     

Shape-Memory Effect in Polymer Composites with a Compactible Filler

The shape-memory effect has been investigated in formed porous polymers and composites under heating. An epoxy polymer, ultrahigh-molecular polyethylene, and polypropylene were used as the polymeric matrix and carbon materials of different bulk density were taken for the filler. An unconventional shape-memory effect, which is accompanied by an increase in volume, was created. Processing schemes by which this effect can be achieved are proposed. They make it possible to obtain products of varying configuration.     

反应等离子喷涂纳米TiN涂层的显微硬度及微观结构研究

阐述了反应等离子喷涂(RPS)方法的基本思想.利用气体隧道等离子喷枪，通过RPS方法在Q23 5钢基底上成功制备了氮化钛涂层.检测了TiN涂层在不同载荷下的显微硬度，结果显示TiN涂层具有明显的硬度压痕尺寸效应，在高载荷下加工硬化效应较弱.XRD,TEM及HRTEM等分析 表明,通过RPS方法制备得到了纳米TiN涂层，涂层由直径约为50—70nm的TiN晶粒及非晶Ti N所组成. 关键词： 反应等离子喷涂 纳米 氮化钛 微观结构