LaC_3~n(n=-1,0,+1)分子簇的理论研究(英文)

用密度泛函方法研究了ＬａＣ３ｎ（ｎ＝－１，０，＋１）分子簇的结构和稳定性，对这个四原子体系，提出了５种可能构型，其中３种具有Ｃ２ｖ对称性，２种为Ｃ∞ｖ对称性．在Ｃ２ｖ对称性结构中，其中１个为Ｌａ接在弯曲的Ｃ３链上，第２个是Ｌａ通过２个键与Ｃ３环相链，第３个是Ｌａ通过１个键与Ｃ３环相连；在Ｃ∞ｖ对称性中，第１个Ｌａ接在Ｃ３链的一端，而在第２个构型中，Ｌａ被插入在Ｃ３链中．结果表明，环状结构当Ｌａ接在弯曲的Ｃ３链上的是局域极小值并且最稳定     

水热法制备高纯超细CeO2-ZrO2复合氧化物

Superfine composite powders of CeO₂-ZrO₂ (CZ) and CeO₂-ZrO₂-La₂O₃ (CZL) were prepared by hydrothermal method. The effects of pH、temperature and time for hydrothermal process on the performance of the resulting powders were studied. The optimized reaction parameters were on follows: the precursor′s pH≈9.0, hydrothermal temperature of 200 ℃ holding for 2 h. Thermal stable powders with average particle size smaller than 10 nm and specific surface area of 171 m²·g^-1 were obtained. A BET specific surface area was still at 44 m²·g^-1 after calcination at 1 000 ℃ for 6 hours.     

Development and validation of a capillary electrophoresis method for the determination of phenothiazines in human urine in the low nanogram per milliliter concentration range using field-amplified sample injection

A capillary zone electrophoresis (CZE) method with ultraviolet-visible detection has been established and validated for the determination of five phenothiazines: thiazinamium methylsulfate, promazine hydrochloride, chlorpromazine hydrochloride, thioridazine hydrochloride, and promethazine hydrochloride in human urine. Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using a buffer containing 150 mM tris(hydroxymethyl)aminomethane and 25% acetonitrile at pH 8.2, with temperature and voltage of 25 degrees C and 20 kV, respectively. Naphazoline hydrochloride was used as an internal standard. Field-amplified sample injection (FASI) has been applied to improve the sensitivity of the detection. Considering the influence of parameters affecting the on-line preconcentration (nature of preinjection plug, sample solvent composition, injection times, and injection voltage) and due to the significant interactions among them, in this paper we propose for the first time the application of a multivariate approach to carry out the study. The optimized conditions were as follows: preinjection plug of water for 7 s at 50 mbar, electrokinetic injection for 40 s at 6.2 kV, and 32 microm of H3PO4 in the sample solvent. Also, a solid-phase extraction (SPE) procedure is developed to obtain low detection limits and an adequate selectivity for urine samples. The combination of SPE and FASI-CZE-UV allows adequate linearities and recoveries, low detection limits (from 2 to 5 ng/mL), and satisfactory precisions (3.0-7.2% for an intermediate RSD %).     

双波长K系数—标准加入吸光光度法同时测定锰和锌

研究应用双波长K系数—标准加入吸光光度法同时测定锰和锌二组分混合物.试验确定了锰和锌测定中K_(Mn)与K_(Zn)的回归方程.对合成试样、人发试样测定,结果满意.     

Analysis of thermal behaviour of high power semiconductor laser arrays by means of the finite element method (FEM)

New results of steady-state two-dimensional finite-element computations of temperature distributions of high power semiconductor laser arrays are presented. The influence of different thermal loads on the 2D temperature distribution in AlGaAs/GaAs gain-guided laser arrays is investigated. TheFEM model is tested by comparing it with analytical solutions. For numerical convenience, the latter is rewritten in a novel form, which is free of overflow problems. The maximum temperatures calculated by both methods agree within 1%. Several factors determining the thermal resistance of the device are quantitatively examined: the ratio of light emitting to non-emitting areas along the active zone, the amount of Joule losses, the current spreading, the solder thickness, and voids in the solder. This yields design rules for optimum thermal performance.     

Selective flow-injection determination of methanol in the presence of ethanol based on a multi-enzyme system with chemiluminescence detection

A highly selective flow-injection system was developed for the determination of methanol. The system consisted of three immobilized enzymes with luminol chemiluminescence detection. First, methanol was oxidized in the presence of alcohol oxidase to yield formaldehyde and hydrogen peroxide. The hydrogen peroxide produced was then destroyed by catalase. The formaldehyde formed in the first stage was further oxidized by NAD⁺-formaldehyde dehydrogenase. The NADH formed was oxidized by 1-methoxy-5-methylphenazinium methylsulphate (1-MPMS), and finally the reduced 1-MPMS was spontaneously oxidized and hydrogen peroxide was produced. The concentration of the hydrogen peroxide produced, which was proportional to the initial concentration of methanol, was determined by luminol chemiluminescence. The determination range was from 0.1 to 100 mg l⁻¹ and the response time was less than 2 min per sample with a relative standard deviation of less than 3%. The system showed good selectivity for methanol; the response was ca. 50 times higher than for ethanol.     

Enhancement of photocurrent generation by honeycomb structures in organic thin films.

A light-emitting poly (distyryldimethylbenzene-co-triethylene glycol) rod-coil block copolymer was used to fabricate films with three-dimensionally ordered honeycomb structures by the breath-figure method. Photocurrent generation and photovoltaic performance are studied, and the dependence of photocurrent on applied electric field is investigated. Introducing the ordered porous structure significantly improves the photoelectric conversion behavior, because porous structures not only enhance the light-harvesting efficiency but also benefit charge separation and charge transfer. This phenomenon may have great prospects for enhancing the photovoltaic behavior of organic thin-film devices.     

Non-stoichiometry of YBa2Cu3O7-d Observed by Repeated Temperature Scanning

Repeated temperature scanning method was applied to observe non-stoichiometry of YBa₂Cu₃O₇-d, and interesting results were obtained. Two simultaneously occurring processes were separately observed in mass change; one is a fast process and the other is slow, so that their responses to the temperature change are quite different from each other. The fast process follows the cyclic temperature change, but the slow process is observed to be a gradual mass change. Kinetic behaviors of these two processes are also made clear by plotting the mass vs. the temperature. Furthermore, a hysteresis loop was observed in the plot of the mass vs. the temperature in a high temperature range presumably due to the third process, and it depends on the heating and cooling rates. This revised version was published online in July 2006 with corrections to the Cover Date.     

Dynamic headspace liquid-phase microextraction of alcohols

A method was developed using dynamic headspace liquid-phase microextraction and gas chromatography-mass spectrometry for extraction and determination of 9 alcohols from water samples. Four different solvents, hexyl acetate, n-octanol, o-xylene and n-decane were studied as extractants. The analytes were extracted using 0.8 microl of n-octanol from the headspace of a 2 ml sample solution. The effect of sampling volume, solvent volume, sample temperature, syringe plunger withdrawal rate and ionic strength of the solution on the extraction performance were studied. A semiautomated system including a variable speed stirring motor was used to ensure a uniform movement of syringe plunger through the barrel. The method provided a fairly good precision for all compounds (5.5-9.3%), except methanol (16.4%). Detection limits were found to be between 1 and 97 microg/l within an extraction time of approximately 9.5 min under GC-MS in full scan mode.     

选相原位法合成立方氮化硼的关键影响因素

利用选相原位法在水溶液中成功制备出了立方氮化硼晶体，对反应条件进行了优化。结果表明，利用选相原位法合成立方氮化硼的最佳实验条件是：反应压力为10.0 MPa，在氯离子加入下利用混合氮源进行反应。在该条件下得到了纯相的立方氮化硼晶体。